Sensorex

BV1 Ball Valve, 1" Full Port, S675, S676, S677 by Sensorex

Sensorex BV-1 full port 1" CPVC ball valve is designed for use with our S675 Series Wet Tap Insertion Assemblies and S656CD pH Sensors. The BV1 mounts a pH sensor in pressurized lines or the sidewall of tanks. Sensors can be retracted for service without shutting down lines or the need to empty tanks. Constructed of durable CPVC.

• Proven design: Remove sensors for cleaning and maintenance without system shutdown
• Full port 1" design: Compatible with Sensorex insertion assemblies & sensors
• One year limited warranty: We stand behind all our products with the Sensorex Guarantee
• Designed for use with our S675 Series Wet Tap Insertion Assemblies and S656CD pH Sensors

CAL-C110 pH & ORP Simulator by Sensorex

The C110 pH/mV checker simulator is a millivolt source that can be used to calibrate or check the calibration of a pH or ORP (mV) meter. It also serves as a troubleshooting toll when pH or ORP systems fail. For troubleshooting, the electrode is removed and the simulator is connected in its place. The C110 sends a signal to the meter to verify the performance of the meter. Signals of pH4, pH7 and pH10 are available, as well as +/-700mV for ORP. A properly working meter (by process of elimination) indicates that the electrode may be the cause of the failure.

Features:

• An essential tool for troubleshooting pH and ORP systems
• Compatible with most pH and ORP systems using BNC connectors
• Simulate high impedance loads
• Instantly ready for use and includes 9V battery
• One year limited warranty

CLD502-MB Chlorine Dioxide Sensor, 485 Modbus output, 0-2 ppm, 10ft cable, Tinned Leads by Sensorex

The CLD series (chlorine dioxide sensors) feature amperometric measurement technology. Designed for disinfection applications in water treatment, for use with chlorine dioxide, pools, etc., these sensors are available in two ranges for detecting ppm level of chlorine dioxide. Choose the CLD502 for 0-2ppm and CLD510 for 0-10ppm of chlorine dioxide.

Typical applications include:

• Industrial wastewater
• Cooling water
• Bottle Rinsing
• Irrigation water in agriculture

Sensors outpu a 4-20mA signal scaled to 0-2, 0-5, or 0-10ppm. Membrane cap and fill solution are easily replaceable to maximize sensor life.

Sensors can be used in new installations with Sensorex flow cell or installed as replacement for other 4-20mA output CIO2 sensors. (Consult Sensorex for compatibility).

An optional flow meter (FM001) is available to help provide consistent flow for added system stability.

Features

• Amperometric Sensor Technology
• Real Time Continuous Measurement
• Ranges 0-2 or 0-10ppm
• Built-In Temperature Compensation
• Large Electroylte Reservoir
• Replaceable Membrane and Electroylte

CLD505-MB Chlorine Dioxide Sensor, 485 Modbus output, 0-5 ppm, 10ft cable, Tinned Leads by Sensorex

The CLD series (chlorine dioxide sensors) feature amperometric measurement technology. Designed for disinfection applications in water treatment, for use with chlorine dioxide, pools, etc., these sensors are available in two ranges for detecting ppm level of chlorine dioxide. Choose the CLD502 for 0-2ppm and CLD510 for 0-10ppm of chlorine dioxide.

Typical applications include:

• Industrial wastewater
• Cooling water
• Bottle Rinsing
• Irrigation water in agriculture

Sensors outpu a 4-20mA signal scaled to 0-2, 0-5, or 0-10ppm. Membrane cap and fill solution are easily replaceable to maximize sensor life.

Sensors can be used in new installations with Sensorex flow cell or installed as replacement for other 4-20mA output CIO2 sensors. (Consult Sensorex for compatibility).

An optional flow meter (FM001) is available to help provide consistent flow for added system stability.

Features

• Amperometric Sensor Technology
• Real Time Continuous Measurement
• Ranges 0-2 or 0-10ppm
• Built-In Temperature Compensation
• Large Electroylte Reservoir
• Replaceable Membrane and Electroylte

CLD510 Amperometric Chlorine Dioxide Sensor, 0-10 ppm, 4-20mA by Sensorex

The CLD series (chlorine dioxide sensors) feature amperometric measurement technology. Designed for disinfection applications in water treatment, for use with chlorine dioxide, pools, etc., these sensors are available in two ranges for detecting ppm level of chlorine dioxide. Choose the CLD502 for 0-2ppm and CLD510 for 0-10ppm of chlorine dioxide.

Typical applications include:

• Industrial wastewater
• Cooling water
• Bottle Rinsing
• Irrigation water in agriculture

Sensors outpu a 4-20mA signal scaled to 0-2, 0-5, or 0-10ppm. Membrane cap and fill solution are easily replaceable to maximize sensor life.

Sensors can be used in new installations with Sensorex flow cell or installed as replacement for other 4-20mA output CIO2 sensors. (Consult Sensorex for compatibility).

An optional flow meter (FM001) is available to help provide consistent flow for added system stability.

Features

• Amperometric Sensor Technology
• Real Time Continuous Measurement
• Ranges 0-2 or 0-10ppm
• Built-In Temperature Compensation
• Large Electroylte Reservoir
• Replaceable Membrane and Electroylte

CLD510-MB Chlorine Dioxide Sensor, 485 Modbus output, 0-10 ppm, 10ft cable, Tinned Leads by Sensorex

The CLD series (chlorine dioxide sensors) feature amperometric measurement technology. Designed for disinfection applications in water treatment, for use with chlorine dioxide, pools, etc., these sensors are available in two ranges for detecting ppm level of chlorine dioxide. Choose the CLD502 for 0-2ppm and CLD510 for 0-10ppm of chlorine dioxide.

Typical applications include:

• Industrial wastewater
• Cooling water
• Bottle Rinsing
• Irrigation water in agriculture

Sensors outpu a 4-20mA signal scaled to 0-2, 0-5, or 0-10ppm. Membrane cap and fill solution are easily replaceable to maximize sensor life.

Sensors can be used in new installations with Sensorex flow cell or installed as replacement for other 4-20mA output CIO2 sensors. (Consult Sensorex for compatibility).

An optional flow meter (FM001) is available to help provide consistent flow for added system stability.

Features

• Amperometric Sensor Technology
• Real Time Continuous Measurement
• Ranges 0-2 or 0-10ppm
• Built-In Temperature Compensation
• Large Electroylte Reservoir
• Replaceable Membrane and Electroylte

CLDA-5018 Chlorine Dioxide Maintenance Kit for CLDS series sensors by Sensorex

Keep your chlorine dioxide amperometric sensors running for extended lifetime and improved accuracy using this chlorine dioxide maintenance kit. Compatible with CLD Series Chlorine Dioxide Amperometric Sensors. This kit includes:

• (1) replacement membrane cap
• (1) replacement pressure relief band
• (2) 30mL bottles of electrolyte refill solution
• (2) 10mL syringes
• (3) polishing squares

CM1000 SensoLab Total Dissolved Solids Meter by Sensorex

The new SensoLab Series Benchtop Conductivity / TDS Meter is the perfect solution for a range of applications from instructional chemistry laboratories to quality control testing. This versatile meter can be powered in two ways, either with 6 AAA batteries to save your valuable bench space or with an AC power cable. Splash resistant casing adds durability, so your meter will stand the test of time.

Features:

• Sleek, small footprint design saves bench space
• Measure Conductivity or TDS and Temperature
• Intelligent auto ranging improves ease of use
• Waterproof case
• Automatic or manual temperature compensation

CM1000-EC2 Kit, CM1000 + CS150TC-K=1/10K/3/8-PIN DIN + TDS1000 + ES100 by Sensorex

The new SensoLab Series Benchtop Conductivity / TDS Meter is the perfect solution for a range of applications from instructional chemistry laboratories to quality control testing. This versatile meter can be powered in two ways, either with 6 AAA batteries to save your valuable bench space or with an AC power cable. Splash resistant casing adds durability, so your meter will stand the test of time.

Features:

• Sleek, small footprint design saves bench space
• Measure Conductivity or TDS and Temperature
• Intelligent auto ranging improves ease of use
• Waterproof case
• Automatic or manual temperature compensation

CS150 Light Duty Online Conductivity Sensor, Graphite, 12mm, 1 M by Sensorex

The CS150 and CS150TC conductivity probes are a cost effective solution for measuring conductivity in light industrial and laboratory applications.

Sensors feature measuring surfaces. The durable epoxy body construction provides a rugged and dependable sensor for portable and laboratory use. Suitable for use with most portable conductivity meters.

By adding a simple mounting gland fitting, customers may use these in process applications. Mount them in-line, in a pipe "T" fitting, or submerse them into a tank.

Features:

• Ideal for laboratory and light duty process applicationsAvailable with or without ATC (temperature sensor)
• Easy to submerge in a tank or mount inline in a pipe
• Cell constant choices of 0.1 or 1.0
• Compatible with most portable and benchtop meters

CS150-B-1-BB-2-A-N CS150 Light Duty Online Conductivity Sensor, Graphite, 12mm, K=0.1, TC, 10FT, BNC by Sensorex

The CS150 and CS150TC conductivity probes are a cost effective solution for measuring conductivity in light industrial and laboratory applications.

Sensors feature measuring surfaces. The durable epoxy body construction provides a rugged and dependable sensor for portable and laboratory use. Suitable for use with most portable conductivity meters.

By adding a simple mounting gland fitting, customers may use these in process applications. Mount them in-line, in a pipe "T" fitting, or submerse them into a tank.

Features:

• Ideal for laboratory and light duty process applicationsAvailable with or without ATC (temperature sensor)
• Easy to submerge in a tank or mount inline in a pipe
• Cell constant choices of 0.1 or 1.0
• Compatible with most portable and benchtop meters

CS150-K=0.1 Light-Duty Contacting Conductivity / TDS Sensor with Automatic Temperature Compensation (ATC), Graphite, 12mm, K=0.1 by Sensorex

The CS150 and CS150TC conductivity probes are a cost effective solution for measuring conductivity in light industrial and laboratory applications.

Sensors feature measuring surfaces. The durable epoxy body construction provides a rugged and dependable sensor for portable and laboratory use. Suitable for use with most portable conductivity meters.

By adding a simple mounting gland fitting, customers may use these in process applications. Mount them in-line, in a pipe "T" fitting, or submerse them into a tank.

Features:

• Ideal for laboratory and light duty process applicationsAvailable with or without ATC (temperature sensor)
• Easy to submerge in a tank or mount inline in a pipe
• Cell constant choices of 0.1 or 1.0
• Compatible with most portable and benchtop meters

CS150-K=0.1/BNC Light-Duty Contacting Conductivity / TDS Sensor with Automatic Temperature Compensation (ATC), Graphite, 12mm, K=0.1, BNC by Sensorex

The CS150 and CS150TC conductivity probes are a cost effective solution for measuring conductivity in light industrial and laboratory applications.

Sensors feature measuring surfaces. The durable epoxy body construction provides a rugged and dependable sensor for portable and laboratory use. Suitable for use with most portable conductivity meters.

By adding a simple mounting gland fitting, customers may use these in process applications. Mount them in-line, in a pipe "T" fitting, or submerse them into a tank.

Features:

• Ideal for laboratory and light duty process applicationsAvailable with or without ATC (temperature sensor)
• Easy to submerge in a tank or mount inline in a pipe
• Cell constant choices of 0.1 or 1.0
• Compatible with most portable and benchtop meters

CS150-K=1 Light-Duty Contacting Conductivity / TDS Sensor with Automatic Temperature Compensation (ATC), Graphite, 12mm, K=1.0 by Sensorex

The CS150 and CS150TC conductivity probes are a cost effective solution for measuring conductivity in light industrial and laboratory applications.

Sensors feature measuring surfaces. The durable epoxy body construction provides a rugged and dependable sensor for portable and laboratory use. Suitable for use with most portable conductivity meters.

By adding a simple mounting gland fitting, customers may use these in process applications. Mount them in-line, in a pipe "T" fitting, or submerse them into a tank.

Features:

• Ideal for laboratory and light duty process applicationsAvailable with or without ATC (temperature sensor)
• Easy to submerge in a tank or mount inline in a pipe
• Cell constant choices of 0.1 or 1.0
• Compatible with most portable and benchtop meters

CS150-K=1/BNC Light-Duty Contacting Conductivity / TDS Sensor with Automatic Temperature Compensation (ATC), Graphite, 12mm, K=1.0, BNC by Sensorex

The CS150 and CS150TC conductivity probes are a cost effective solution for measuring conductivity in light industrial and laboratory applications.

Sensors feature measuring surfaces. The durable epoxy body construction provides a rugged and dependable sensor for portable and laboratory use. Suitable for use with most portable conductivity meters.

By adding a simple mounting gland fitting, customers may use these in process applications. Mount them in-line, in a pipe "T" fitting, or submerse them into a tank.

Features:

• Ideal for laboratory and light duty process applicationsAvailable with or without ATC (temperature sensor)
• Easy to submerge in a tank or mount inline in a pipe
• Cell constant choices of 0.1 or 1.0
• Compatible with most portable and benchtop meters