Manhole Sleeves & Bases, Pelsue

DSC-S1 Sleeve Cap, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Sleeve Caps

Used to seal sleeves when not in use. Available in zinc plated steel, stainless steel or ABS plastic. Has a rubber seal that expands into sleeve

DSR-A08 Portable Wall Mounted Plate/Sleeve, Aluminum by Pelsue

For clamping onto a wall ranging from 3" to 8" thick walls.

DSP-C2 Cylinder Core, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Cylinder Core

The cylinder core mount is drilled into existing concrete or poured into fresh concrete and must be secured to the concrete with grout or epoxy compatible with plant conditions. Please contact Pelsue for specific installation requirements.

DSP-A2 Wall Mounted Plate/Sleeve 90 Degree Outside Mount, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Corner Mounted

Inside 90° angle. The corner mount is anchored by bolts to reinforced truck bumpers, walls, etc. Please contact Pelsue for specific installation requirements. Zinc plated steel.

DSS-F3 Flush Floor Mount Sleeve for Existing Concrete, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Flush Floor Mounted

Placed in fresh concrete, this sleeve mounts flush with the floor and is great for high traffic areas where trip hazards are a concern. Please contact Pelsue for specific installation requirements.

DSS-C1 Flush Floor Mount Sleeve for Fresh Pour Concrete, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Flush Floor Mounted

Placed in fresh concrete, this sleeve mounts flush with the floor and is great for high traffic areas where trip hazards are a concern. Please contact Pelsue for specific installation requirements.

DSR-ADJ Portable Wall Mounted Plate/Sleeve, Adjustable, Powder Coated Steel, 24" by Pelsue

The adjustable wall mount can clamp to any wall ranging from 1" to 23-1/4" thick.

DSS-C2 Cylinder Core, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Cylinder Core

The cylinder core mount is drilled into existing concrete or poured into fresh concrete and must be secured to the concrete with grout or epoxy compatible with plant conditions. Please contact Pelsue for specific installation requirements.

DSC-P1 Sleeve Cap, Plastic by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Sleeve Caps

Used to seal sleeves when not in use. Available in zinc plated steel, stainless steel or ABS plastic. Has a rubber seal that expands into sleeve

DSS-F1 Floor Mounted Baseplate/Sleeve, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Floor Mounted

The floor mount is anchored by bolts, or it welds to a variety of surfaces such as floors, truck beds, catwalks, etc. Contact Pelsue for specific installation requirements.

DSS-F2 Floor Mounted Center Baseplate/Sleeve, Stainless Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Floor Mounted

The floor mount is anchored by bolts, or it welds to a variety of surfaces such as floors, truck beds, catwalks, etc. Contact Pelsue for specific installation requirements.

DSC-S2 Sleeve Cap, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Sleeve Caps

Used to seal sleeves when not in use. Available in zinc plated steel, stainless steel or ABS plastic. Has a rubber seal that expands into sleeve

DSP-F3 Flush Floor Mount Sleeve for Existing Concrete, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Flush Floor Mounted

Placed in fresh concrete, this sleeve mounts flush with the floor and is great for high traffic areas where trip hazards are a concern. Please contact Pelsue for specific installation requirements.

DSP-F2 Floor Mounted Center Baseplate/Sleeve, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Floor Mounted

The floor mount is anchored by bolts, or it welds to a variety of surfaces such as floors, truck beds, catwalks, etc. Contact Pelsue for specific installation requirements.

DSR-S03 Portable Wall Mounted Plate/Sleeve, Powder Coated Steel, Max. 3" by Pelsue

The DSR-S03 portable wall mount is made of zinc plated carbon steel. Clamping via eight bolts, the wall mount straddles walls of tanks, caissons, shorings, etc. up to 3" thick.

DSP-F1 Floor Mounted Baseplate/Sleeve, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Floor Mounted

The floor mount is anchored by bolts, or it welds to a variety of surfaces such as floors, truck beds, catwalks, etc. Contact Pelsue for specific installation requirements.

DSP-W1 Wall Mounted Plate/Sleeve, Powder Coated Steel by Pelsue

The wall mount is anchored by bolts or welds to truck bumpers, tank walls, sides of catwalks, meter pits, clarifiers, etc. Please contact Pelsue for specific installation requirements.

DSP-C1 Flush Floor Mount Sleeve for Fresh Pour Concrete, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Flush Floor Mounted

Placed in fresh concrete, this sleeve mounts flush with the floor and is great for high traffic areas where trip hazards are a concern. Please contact Pelsue for specific installation requirements.

DSS-W1 Wall Mounted Plate/Sleeve, Stainless Steel by Pelsue

The wall mount is anchored by bolts or welds to truck bumpers, tank walls, sides of catwalks, meter pits, clarifiers, etc. Please contact Pelsue for specific installation requirements.

DSP-A1 Wall Mounted Plate/Sleeve 90 Degree Inside Mount, Powder Coated Steel by Pelsue

Permanent Mount Sleeves

• Available in electroless nickel plated steel, zinc plated, galvanized or stainless steel
• ABS liners with PVC slip plates
• Accepts up to 48" offset masts
• Sleeve is always on site
• Inside sleeve diameter 3.0680"
• Liners and sleeves are replaceable
• Allows masts to pivot 360°
• Drain holes eliminate water buildup
• Friction bearing is replaceable

Corner Mounted

Inside 90° angle. The corner mount is anchored by bolts to reinforced truck bumpers, walls, etc. Please contact Pelsue for specific installation requirements. Zinc plated steel.