$1000 - $2000, Fixed System Gas Monitors

2214034 CS 21 Fixed Gas Transmitter, Freon 507, 0(30) - 1,000 ppm by GfG

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants
• Long sensor life
• Fast response

4400 4000 Series Integrated Controller, 4 Channels, 2 Amp Power Supply by GfG

The 4100 one-channel and the 4-channel 4400 gas warning systems offer safe and reliable gas detection

Alarm points

Each alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The alarm point values can be freely adjusted within the detection range of the transmitter. Every alarm point value can be selected to be latching / non-latching or resettable / non resettable.

Alarm relays

The controller provides four voltage-free relays for the three alarms in addition to one fault warning. The relays may be used to control additional alarm devices like lights or horns. They can even prompt specific counter measures to prevent or limit dangers from gases or vapors.

Additional features

The 4100 control panel stores peak values and offers an additional 4-20 mA output. The 4400 control panel offers the ability to connect up to 4 transmitters and comes standard with an additional 24 VAC output for solenoid control.

Features

• Complete 1-to-4 channel controller / gas monitoring system
• 110 VAC or 24 VAC
• Case-mounted horn / strobe
• Security lock
• Slim-line design

SPXCDULNFX UL/CSA/INMETRO approved SP XCD Flammable CAT 0-100%LEL (20 to 100%LEL, 10%LEL) with LM25, 3/4 NPT Entry by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

SPXCDXSB2SS Sensepoint XCD Gas Detector, Carbon Dioxide IR 0-5.00% v/v only by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

TXgard and Flamgard Plus

With over 40 years of experience in gas detection technology and development, Crowcon Detection Instruments is pleased to present one of its most economical gas sensing devices. With its one man calibration system, life-long sensors, and simple parts replacement, the Txgard and Flamgard Plus range of detectors offer a reliable and cost efficient solution for most gas detection needs.

With its mission to protect people and plant from gas hazards, the newest line of gas detecting instruments include exclusive state of the art features including:

• Marine grade with stainless steel housing
• A wide range of reliable and advanced gas detecting sensors
• Flexible output options
• Optional relays for alarm and fault
• Quick response times
• Easy to read screen displays
• Easy to operate calibration methods
• Efficient and economical sensor and gas detection technology

Rugged, Reliable, and Flexible

The detector models are constructed to withstand the abuse of hazardous work environments. The TXgard and Flamgard Plus detectors use marine grade aluminum with a stainless steel sensor housing to ensure the safety and integrity of the equipment. The TXgard-IS+ is constructed of carbon-loaded nylon. The models also feature flexible output options including 2 or 3 wire formats, optional relays for alarm and fault, and 4-20mA current sink or source. Crowcon also has a wide variety of catalytic and electrochemical gas sensors to fit these models (currently offering more than 25 individual gas sensors).

Flamgard Plus and TXgardPlus Specifications

The Flamgard Plus and TXgard Plus models are similar in size (200 x 115 x 115 mm) and weight (2.2 kilograms). However, the Flamgard Plus utilizes a catalytic bead sensor and the TXgard Plus utilizes an electrochemical sensor. Both feature an ingress protection with an IP66 weatherproof cap and 2 x M20 x ½ NPT cable entries. These models feature optional relays of SPNO or SPNC contacts rated 30 Vdc 1A (non-inductive load) for Alarm 1 and fault for Alarm 2.

For easy reading, these models have a 3 digit backlit display with and LED status indicator. The magnetically operated buttons control the calibration method and the terminals are suited for up to 1.5 mm2 cable. Both models are suited for usage in hazardous zones 1 and 2.

TXgard IS+ and Specs

The TXgard IS+ is slightly smaller than the other two models and houses an electrochemical sensor type. It is approximately 160 x 123 x 92 mm in size and .7 kilograms in weight. This unit also features an IP66 weatherproof cap for ingress protection. The display is slightly smaller than the other two models, and offers a 2 line 16 character LCD screen. The calibration method is operated via front mounted push buttons, and its terminals are suited for up to 2.5 mm2 cables. This model is appropriate for hazardous zones 0, 1, and 2, and when connected via an isolation device, the TXgard IS+ is suited for hazardous zones 20, 21, and 22.

*Please note we can only ship RKI products to customers within the United States

SPXCDUSNTXT Sensepoint XCD Transmitter, Toxic Tx, UL, SS316 by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

TXISP-H2S-SIDE-Sira-100 TXgard-IS+ Toxic Gas Detector with Display, Hydrogen Sulphide 0-100 ppm by Crowcon

TXgard-IS+ is a Intrinsically Safe (I.S.) toxic and oxygen gas detector with local LCD display. A wide choice of sensors are available for use in a variety of applications.

Features:

Non-intrusive calibration

• Calibration can be performed locally without the need for hot work permits
• Local display and buttons enable calibration without opening the junction box

Flexible output options

• A two-wire 4-20mA signal is provided
• The output can be forced up without applying gas to enable simple checking of control systems and alarms.

Rugged and reliable

• Constructed using highly durable GRP to provide good impact resistance
• Ingress protection to IP65 as standard, IP66 with accessory
• IEC61508 SIL compliant

SPXCDALMRX Sensepoint XCD Gas Detector, 4 to 20 mA output, ATEX/IECEx/Asian approvals, 2 x M20 entries, painted LM25, includes infrared methane sensor cartridge 0 to 100%LEL, user selectable FSD between 20% and 100%LEL (10%LEL resolution), includes nylon weather protection by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

65-2462RK S2 Series Hydrogen (H2) 0 - 10% Vol Sensor (TC)/Transmitter, Explosion Proof with J-Box by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

65-2630RK-05 M2, IR Carbon Dioxide 0 - 50%, Sensor/Transmitter with J-Box, UL Version by RKI Instruments

RKI Instruments uses the latest cutting edge technology when developing transmitters and sensors. Its dedication to workplace safety and reliable safety solutions is unparalleled. The M2 Stand Alone Transmitter utilizes state of the art sensor cell technology to integrate workplace safety with the industry's more advanced transmitter technologies.

M2 Stand Alone Transmitter

The M2 Stand Alone Transmitter is operational with or without a controller and is available in two forms: explosion proof and non-explosion proof. The unit has a backlit screen for a direct digital readout, and a user friendly setup with push buttons and easy to read LCD menus. The advanced technology transmitter can function as an independent standalone system or as part of an integrated detection and transmission system. Using state of the art technology, the transmitter uses a magnetic want technique for performing non-intrusive calibration. For optimal stability and accurate readings, the unit provides an automatic zero drift correction feature. This also reduces the need for adjustments due to sensor aging.

The M2 Stand Alone Transmitter is available for LEL, H2S, CO, PPM, HC, CO2, CI2, NH3, SO2, HCN, and more. The unit also features an infrared sensor for CO2 and combustible gases. With 2 fully programmable alarms and a fail relay, the visual color coded LED alarms are reliable and customizable to meet specific needs.

Advanced sensor technology

The state of the art sensors are long lasting with a lifespan typically over two years. Sensor construction is rated Class I, Division 1 groups B, C, and D for flammables, CO, H2S, O2, and CO2. The sensors are rated Class I, Division 2 for all other toxic gases. Depending on the gas, the sensors will operate through a catalytic, galvanic cell, electrochemical, or infrared design. The plug in nature of the sensors allows for a quick and tool free onsite replacement.

Specifications

Each transmitter features 2 to 3 years of life with normal service. The explosion proof LEL H2 specific transmitter has 3 to 5 years with normal service, and the explosion proof carbon dioxide, methane, and hydrocarbons feature over 5 years of life with normal service. The explosion proof transmitters are also water repellant. Each device is approximately 8.5 H x 5.2 W x 4.5 D and features an alphanumeric display with a backlight. The screen displays 8 characters per line with 2 lines for gas concentration readouts.

Optional Accessories

The M2 Stand Alone Transmitter has a variety of optional accessories available including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and dataloggers. The transmitters are directly compatible with Beacon 110, 200, 410, and 800 controllers.

*Please note we can only ship RKI products to customers within the United States

SPXCDALMTXO Sensepoint XCD Transmitter, O2 Tx, ATEX, LM25 by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

72-2102RK-01 Beacon 200 Two Channel Wall Mount Controller, 115 VAC with Red Strobe Light (uses Common Alarm 1 Relay Contact for Strobe) (No Sensors) by RKI Instruments

RKI Instruments is an industry leader in gas monitoring and detection devices. Understanding the unique needs of hazardous workplace conditions, RKI Instruments offers the widest selection of standard and toxic gas detection sensors. With an emphasis on reliability and dependency, their products are some of the safest and most dependable gas monitors on the market. In researching workplace safety solutions, RKI's research and development team used the latest microprocessor technology to develop the Two Channel Wall Mount Controller Beacon 200 Model, a gas detection system designed with the everyday hazards of dangerous work environments in mind.

Two Channel Wall Mount Controller

The Two Channel Wall Mount Controller Beacon 200 Model utilizes microprocessors and state of the art technology to ensure accurate gas detection and alert those nearby of atmospheric conditions. The unit is affordable, versatile, user-friendly, and easy to install. This model connects directly to long lasting RKI sensors for LEL level combustible gases, oxygen, and toxic gases. These sensors may be connected directly to the unit or may be wired remotely.

Two Channel Wall Mount Controller Beacon 200 Model Features

The unit features simultaneous atmospheric condition readout on 2 channels with 2 alarm levels per channel and a built in audible alarm system. The unit also houses 4-20 mA outputs and accepts any 4-20 mA transmitter input (24 VDC). The unit can also be wired with a variety of RKI Instrument sensors.

The Two Channel Wall Mount Controller Beacon 200 Model is housed in a wall mounting grey polycarbonate casing with a hinged cover. The NEMA 4X enclosure is waterproof, chemical resistant, and weather resistant ensuring maximum protection against potential environmental hazards that could damage safety equipment. It is user-friendly with 4 push buttons for setup, programming, and calibration. The unit also features 1 external push button for alarm reset.

The alarm system features an audible and visual alert system. The built-in audible alarm uses a 94 dB alert system, and the visual alerts feature 4 ultra-bright LED lights on the front cover. The alarms will alert users about potentially dangerous atmospheric conditions in addition to potential unit malfunctions.

Beacon 200 Model Specifications

The Two Channel Wall Mount Controller Beacon 200 Model features a backlit alphanumeric display that is easy to read and practical with 20 characters per line and a 4 line capacity. The wall mounted controller is approximately 10.5 H x 8.5 W x 6.3 D and is powered by 115 VAC or 24 VDC standard with an optional 230 VAC and an available battery backup option. The Two Channel Wall Mount Controller Beacon 200 Model is CSA Certified and comes standard with a 1 year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

72-2102RK-220 Beacon 200 Two Channel Wall Mount Controller, 220 VAC (No Sensor) by RKI Instruments

RKI Instruments is an industry leader in gas monitoring and detection devices. Understanding the unique needs of hazardous workplace conditions, RKI Instruments offers the widest selection of standard and toxic gas detection sensors. With an emphasis on reliability and dependency, their products are some of the safest and most dependable gas monitors on the market. In researching workplace safety solutions, RKI's research and development team used the latest microprocessor technology to develop the Two Channel Wall Mount Controller Beacon 200 Model, a gas detection system designed with the everyday hazards of dangerous work environments in mind.

Two Channel Wall Mount Controller

The Two Channel Wall Mount Controller Beacon 200 Model utilizes microprocessors and state of the art technology to ensure accurate gas detection and alert those nearby of atmospheric conditions. The unit is affordable, versatile, user-friendly, and easy to install. This model connects directly to long lasting RKI sensors for LEL level combustible gases, oxygen, and toxic gases. These sensors may be connected directly to the unit or may be wired remotely.

Two Channel Wall Mount Controller Beacon 200 Model Features

The unit features simultaneous atmospheric condition readout on 2 channels with 2 alarm levels per channel and a built in audible alarm system. The unit also houses 4-20 mA outputs and accepts any 4-20 mA transmitter input (24 VDC). The unit can also be wired with a variety of RKI Instrument sensors.

The Two Channel Wall Mount Controller Beacon 200 Model is housed in a wall mounting grey polycarbonate casing with a hinged cover. The NEMA 4X enclosure is waterproof, chemical resistant, and weather resistant ensuring maximum protection against potential environmental hazards that could damage safety equipment. It is user-friendly with 4 push buttons for setup, programming, and calibration. The unit also features 1 external push button for alarm reset.

The alarm system features an audible and visual alert system. The built-in audible alarm uses a 94 dB alert system, and the visual alerts feature 4 ultra-bright LED lights on the front cover. The alarms will alert users about potentially dangerous atmospheric conditions in addition to potential unit malfunctions.

Beacon 200 Model Specifications

The Two Channel Wall Mount Controller Beacon 200 Model features a backlit alphanumeric display that is easy to read and practical with 20 characters per line and a 4 line capacity. The wall mounted controller is approximately 10.5 H x 8.5 W x 6.3 D and is powered by 115 VAC or 24 VDC standard with an optional 230 VAC and an available battery backup option. The Two Channel Wall Mount Controller Beacon 200 Model is CSA Certified and comes standard with a 1 year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

SPXCDALMTXFM Sensepoint XCD Transmitter, Flam and IR Tx, ATEX, LM2 by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

3601-030 EC 36 Fixed Gas Transmitter, Oxygen (O2), Display / Alarm Relays by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment