Modern Water

7020301 PCB EnviroGard 12T Soil Test Kit by Modern Water

Envirogard® is a rapid field enzyme immunoassay method for the analysis of soil remediation, assessment and industrial testing. It uses a coated tube technology to detect the analyte of concern.

Features:

• Convenient and rapid testing in the field or labatory
• Tests up to 10 samples at once
• Two detection levels of your choice are provided with each sample
• High level of accuracy
• EPA SW-846 Method #4020

Test result type

• Semi-quantitative or qualitative data
• Knowledge of specific aroclor(s) present will aid accuracy

Samples per kit

• Dependent on batch size and number of detection levels
• Each sample can be tested one at a time or in batches of two to ten samples

Assay range

• Soil: 0.5 ppm to 500 ppm with dilutions
• Wipes: 5.0 ug/100cm² to 5000 ug/100cm² with dilutions

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately)
• The sample extraction kit provides materials for 12 soil sample extractions with methanol

Sampling time

• Approximately two minutes per sample plus assay run time of approximately 30 minutes

Basic Test Procedure

• Transfer soil or wipe to extraction jar
• Cap and shake for one minute
• Filter extracted sample
• Pipette and dilute samples with dilution ampule
• Transfer 1 ml of buffer to glass buffer tubes
• Pipette and transfer sample to buffer tubes
• Fit antibody coated tubes on buffer tubes; invert and mix;return to antibody coated tube
• Incubate for 10 minutes
• Connect antibody coated and conjugate tubes; invert and mix, return to antibody coated tube
• Incubate five minutes
• Wash antibody coated tubes vigorously four times
• Using a repeater pipette at setting two and 5 mL tip,transfer 200 uL substrateA to each tube
• Add 200 uL substrate B to each tube and mix
• Inclubate for 2.5 minutes
• Add 200 uL STOP to each tube
• Read tubes in photometer.Record data

Test kit components

• 48 antibody coated tubes and PCB enzyme conjugate vials
• 48 glass buffer tubes
• Substrate and stop solution reagents
• PCB standard
• Pipette tips and bulb pipettes
• Buffer
• Amber vials
• Wash solution
• 12 ampule crackers

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging.
• Store at ambient temperature 64° to 81°F (18° to 27°C)
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not freeze test kit components

Required test materials

• PCB EnviroGard 12T accessory kit (6050400)
• PCB EnviroGard 12T accessory kit rental (Includes all equipment required to operate test and interpret results)(6997020)

Required test equipment

• PCB EnviroGard 12T soil test kit (7020301)
• PCB soil sample extraction kit (7020301EB)
• EnviroGard PCB wipe sample extraction kit (7020301WA)

Other recommended materials

• Absorbent paper
• Liquid waste container
• Disposable gloves
• Marker pen
• Liquid and solid waste containers

A00134 RaPID Assay PCBs 100 Tube Kit by Modern Water

RaPID Assay® is a rapid field or laboratory enzyme immunoassay method for the analysis of soil and water for remediation, assessment, and industrial testing.

Features:

• Rapid field testing procedure for analysis of soil and water samples
• Quantitative data results with excellent analytical precision
• Results available in approximately 60 minutes
• Training available
• Magnetic particle immunoassay
• EPA SW-846 method #4020

Test result type

• Quantitative, semi-quantitative or qualitative

Samples per kit

• 100 test kit (tests up to 80+ samples)

Assay range

• Soil: 0.5 ppm to 10 ppm total PCB's as Aroclor 1254
• Water: 0.25 to 5.0 ppb total PCB s as Aroclor 1254
• Wipes: 5 to 100μg per wipe total PCB s as Aroclor 1254
• Range can be extended with additional dilutions

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately).
• The sample extraction kit provides materials for 12 soil sample extractions with methanol.
• Water samples must be diluted one part sample to one part methanol to prevent adsorptive loss.

Sampling time

• Soil extraction time is typically two minutes per sample plus assay run time of approximately 60 minutes

Specificity

The table below shows compounds at the method detection limit(MDL) which isthe lowest concentration of the compound that can be picked up in the assay. The limit of quantification (LOQ)- an approximate concentration required to yield a positive result at the lowest standard. The IC50 is the concentration required to inhibit one-half of the colour produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Basic Test Procedure

• Add calibrators and sample, enzyme conjugate, and antibody coupled magnetic particles to a test tube. Vortex.
• Incubate for 15 minutes
• Using the RaPID magnetic separator, decant and wash two times
• Add colour solution and incubate for 20 minutes
• Stop the reaction and read colour at 450 nm
• Quantitive results and QC parameters are calculated and printed automatically using the RPA spectrophotometer

Test kit components

• Antibody coated magnetic particles for analysis of 100 test tubes
• Zero standard, wash, enzyme conjugate, colour development and stop reagents
• Standards for 0.25, 1.00 and 5.0 ppb as Aroclor 1254
• Kit control as 3.0 ppb as Aroclor 1254
• Disposable test tubes
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• PCB Assay 100 tube kit (A00134)
• Sample extraction kit(for soil samples only) (A00137EB)
• Sample extraction kit(for wipe samples only) (A00137WB)
• PCB sample diluent 100mL (A00136)

Required test equipment

• RaPID Assay accessory kit which contains (6050100 (P)/6997010 (R)): RPA-I1 RaPID analyser (6000081), Printer (6000082), Magnetic separation rack (A00004), Repeator pipet (A00008), Adjustable volume pipet (A00176), Vortex mixer (A00014), Portable balance (A00131), Digital timer (A00015)
• Repeator pipet tips(12.5 mL) (A00009)
• Adjustable pipet tips (A00013)

Other recommended materials

• Latex gloves
• Liquid and solid waste containers
• Calculator
• Absorbant paper for blotting
• Marking pen

7210000 EnviroGard Triazine Test Kit by Modern Water

Envirogard® is a rapid field enzyme immunoassay method for the analysis of water. It uses a coated tube technology to detect the analyte of concern.

Features:

• The first environmental immunoassay format to be made commercially available
• Broad screen for the triazine family of herbicides including atrazine
• Rapid field method for the analysis of drinking and environmental water samples
• Test up to six tubes at once
• Coated tube immunoassay

Test result type

• Qualitative and Semi-quantitative data

Samples per kit

• 20 tube test kit (tests up to 12 samples)

Assay range

• 0.1 ppb to 1.0 ppb
• LDD = 0.053 ppb (atrazine)

Sample methods

• Water and a variety of other matrices

Sampling time

• Sample-to-data in approximately 10 minutes

Specificity

The EnviroGard® Triazine Test Kit does not differentiate between atrazine and closely related compounds, but detects their presence to differing degrees. The chart below shows the approximate Lower Limits of Detection (LDD) for the cross-reacting compounds.

Basic Test Procedure

• Add 160 uL of calibrator, negative control or sample to the tube
• Add four drops of enzyme conjugate
• Incubate for five minutes
• Decant and wash four times
• Add four drops of substrate and chromogen
• Incubate for two minutes
• Add one drop of stop solution
• Read on photometer

Test kit components

• 20 antibody-coated test tubes
• One vial of negative control
• One vial of atrazine-enzyme conjugate
• One vial of 0.1 ppb atrazine calibrator
• One vial of 1.0 ppb atrazine calibrator
• One vial each substrate and chromagen
• One vial stop solution
• One test tube rack

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use for up to 8 hours
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• Triazine EnviroGard® test kit (7210000)

Required test equipment

• Disposable-tip pipette which will measure 160 uL
• Timer
• Glass tubes or vials for calibrator preparation
• Tap or distilled water for rinsing tubes
• Marker pen
• Pipette that will measure 0.5mL

Other recommended materials

• Calculator
• Spectrophotometer

AZF686300 Microtox SOLO Reagent, 50 vials per box by Modern Water

SOLO Reagent is the same as Acute Reagent - packaged to run a single test

Accessories required:

• Disposable Glass Cuvettes: box of 1000 - AZF686004
• Cuvette Racks (set of 5) - AZF686250
• Oxford® Fixed Volume 10 uL Pipette (for high toxicity protocol only) - AZF686067
• Adjustable Volume Pipette: 10 - 100 uL - AZF686087
• Adjustable Volume Pipette: 100 - 1000 uL (for all protocols) - A00176
• 10-100 uL Wide Bore Pipette Tips: tray of 96 - AZFV020
• 100-1000 uL Wide Bore Pipette Tips: tray of 100 - AZFV021
• Microtox® Diluent: 1L bottle - AZF686011
• Microtox® Osmotic Adjusting Solution: 1 x 50 mL - AZF686019

7085000 EnSys RDX Explosives Soil Test Kit with Extraction Jars by Modern Water

Ensys® explosives kits are rapid field or laboratory colourimetric tests for the analysis of explosives in soil. The kits are based on a method developed by Dr. Thomas Jenkins at the US Army Corps of Engineers - CRREL.

Features:

• Detects RDX, HMX and related explosives
• Convenient and rapid testing in the field or laboratory
• Extractions can be performed simultaneously with analysis in singlicate
• Can test sample extract from EnSys TNT test
• Training recommended
• EPA SW-846 Method #8510 (proposed status final with 4th update)

Test result type

• Quantitative data

Samples per kit

• 20 soil samples

Assay range

• Soil: 1 ppm to 30 ppm total RDX
• Higher sample concentrations can be quantified by sample extract dilution

Sample preparation

• Soil samples require prior extraction using the included extraction components
• Soil samples should be dried prior to analysis
• Soil sample extracts from TNT soil test kit may be used

Sampling time

• 'Dirt-to-Data' in approximately 30 minutes
• Typically about six samples can be run in about one hour
• Soil extraction time is typically 2 - 10 minutes per sample plus test run time of approximately 20 minutes

Specificity

The Ensys® RDX test is specific for RDX, HMX and related explosive compounds and exhibits the following sensitivities. The RDX does not measure TNT, TNB or DNB.

Basic Test Procedure

• Clean cuvettes and set spectrophotometer
• Extract soil sample: Weigh 10 grams of soil sample, Add sample to extraction jar, Measure 50mL acetone into 50mL tube, Pour acetone into extraction jar and shake for three minutes, Allow to settle for five minutes
• Draw into syringe 5.5mL liquid from above the sediment layer in extraction jar
• Attach filter tip to syringe and transfer 5mL of sample extract into a 13mL tube
• NOTE: if nitrate/ nitrate interferents are present, attach an Alumina-A cartridge to the syringe and dispense through this
• Cut open an acetic acid bulb and add contents to the 13mL tube. Cap and shake
• Cut open a NitriVer pillow and add it to a 50mL reaction vial containing water
• Quickly pour acetic acid and sample into 13 mL zinc tube and cap. Invert twice and expose sample to zinc for EXACTLY 15 seconds
• With the filter attached to syringe and plunger removed, hold over reaction vial and pour zinc solution into it
• Rapidly filter the solution into the 50mL reaction vial, cap and shake for 30 seconds
• Incubate for 15 minutes for colour development and transfer contents to 30mL syringe barrel. Attach syringe filter and dispense into spectrophotometer cuvette
• Place cuvette in spectrophotometer and record absorbance
• Calculate results

Test kit components

• 20 weigh boats and wooden spatulas
• 20 extraction jars
• One 50mL graduated tube
• 20 - 50mL reaction vials with H2O
• 20 - 13mL zinc tube in foil pouches
• 20 - 10cc, 20cc and 30cc syringes
• 20 - 30mL tubes
• 20 NitriVer pillows
• 20 acetic acid bulb pipettes
• 60 syringe filters
• 1 bulb pipette
• 1 RDX control vial and ampoule cracker
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging.
• Store kits at room temperature (less than 80°F (27°C))
• Operate the test at temperature greater than 40°F/4°C and less than 100°F/39°C
• Do not expose the kits to direct sunlight

Required test materials

• EnSys RDX explosivessoil test kit (7085000)
• EnSys TNT explosives soil test kit (7002000)

Required test equipment

• Acetone: hardware or laboratory grade (min 50mL per sample)
• Alumina-A cartidges (if nitrate/nitrate interferents present) (6021200)

Other recommended materials

• Scissors
• Tap or laboratory grade water for cuvette rinsing
• Hach DR/2000, DR/2010 or DR/2800
• 2 matched hach cuvettes
• 2 cuvette stopper plugs
• Balance
• Marker pen, calculator
• Absorbent paper
• Liquid waste container
• PPE: Disposable gloves, eyewear

AZF50H100 MicrotoxOmni Software version 4.2 by Modern Water

Provided with purchase of Microtox® M500 analyser:

• ASTM (D5660)
• Basic toxicity test
• Comparison test
• Confirmation test
• ISO (International Standard Organization 11348-3)
• DIN (Deutsches Institut fur Normung 38412 Teil Test)
• Screening toxicity test
• Solid Phase/Basic Solid Phase
• Comparison
• Confirmation
• WET (Whole Effluent Toxicity)

7065400 PetroFLAG™ Analyzer for Petroleum Hydrocarbons by Modern Water

Rapid and simple field testing procedure for broad range hydrocarbon contamination in soil which is most sensitive to heavier hydrocarbons such as oils and greases.

PetroFLAG is an environmentally safe, inexpensive, field portable test to determine the total petroleum hydrocarbons in soil. It is both safe and easy to use.

PetroFLAG does not distinguish between aromatic and aliphatic hydrocarbons, but quantifies all fuels, oils, and greases as total hydrocarbons. Analysis of a 10 gram soil sample is performed using three simple steps: extraction, filtration, and analysis.

The PetroFLAG system is completely field portable. Everything needed to perform ten soil tests can be conveniently carried to the job site in a briefcase size carrying case. The PetroFLAG meter is a light-weight, rugged hand-held unit powered by a 9-volt alkaline battery. The meter is menu driven for ease of use and utilises an EEPROM memory system. Fifteen response factors are built into the analyser depending on the analyte of interest. Response factors correlate to fuels ranging from weathered gasoline to heavy crude oil. The results are shown in ppm on an LCD display screen.

PetroFLAG has been assigned a USEPA SW-846 Draft Method 9074.

• Quantitative or semiquantitative results for up to 14 fuels
• Test up to 10 samples at once
• Detection range 10 - 10,000 ppm (fuel type dependent)
• Dexsil patented chemistry
• EPA SW-846 Method# 9074

Specificity

The PetroFLAG hydrocarbon in soil test kit is used in conjunction with the PetroFLAG analyser to allow users to select the response factor that is appropriate for the suspected contaminant at each site. The following are response factors and Method Detection Limits for common hydrocarbons:

Basic Test Procedure

• Prepare soil extraction tube and developer vial by labeling with sample ID.
• Weigh 10 grams of soil into labeled tube.
• Set timer for 5 minutes.Add extraction solvent to labeled tube. Shake and incubate for 1minute.
• Pour free liquid from labeled tube into syringe barrel, add plunger and dispense into 6 ml vial.
• Add extraction solvent to developer solution. Shake for 10 seconds.
• Set timer for 10 minutes.
• Read results of developed samples in PetroFLAG Anlayser. Select pre-programmed response factor

Test kit components

• 12 blue-capped polypropylene soil tubes
• 12 polypropylene filter assemblies
• 12 screw capped developer vials
• 11 break-top vials containing soil extraction solvent
• adhesive labels
• 1 break-top vial containing calibration solution
• 12 metal spatulas

Storage & precautions

• Shelf life typically one year from date of manufacture, with specific kit expiration dateinformation provided on product packaging.
• Components can be stored and operated at room temperature.
• Extraction solvent and calibration standards contain methanol.
• PetroFLAG analyser must be used at temperatures from 4°C to 45°C.

Required test materials

PetroFLAG analyser contains: 10 soil reagents, calibration standards, digital-hand held analyzer, digital balance, timer and carry case.

Required test equipment

PetroFLAG soil 10 pack reagents

Other recommended materials

• Personal protective clothing (i.e. latex gloves)
• Liquid and solid waste containers
• Absorbant paper for blotting
• Notepad for record keeping

7311000 EnviroGard Chlordane in Soil Kit by Modern Water

Envirogard® is a rapid field enzyme immunoassay method for the analysis of soil remediation, assessment and industrial testing. It uses a coated tube technology to detect the analyte of concern.

Features:

• Rapid field testing kit
• Semi-quantitative results at set calibrator (action) levels
• Test up to 16 samples at one time
• Results in less than 30 minutes
• Coated tube immunoassay
• Training available
• EPA SW-846 Method #4041

Test result type

• Semi-quantitative data or qualitative

Samples per kit

• Up to 16 soil samples depending on the number of runs and action levels used. (Kit includes 20 antibody coated tubes)

Assay range

• Semi-quantitative results (greater or less than) at calibrator (action) levels of 20, 100 and 600 ppb total Chlordane
• Minimum detection limit (MDL) is 20 ppb Chlordane
• No maximum screening level as extracts can be diluted into test range

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately)
• The sample extraction kit provides material for 12 soil sample extractions with methanol

Sampling time

• Approximately two minutes per sample plus assay run time of approximately 30 minutes

Sampling time

The EnviroGard® Chlordane immunoassay test does not differentiate between Chlordane and other cyclodienes. The table below shows compounds at the minimum detection limit (MDL) - an approximate concentration required to yield a positive result at the lowest standard. The IC50 is the concentration required to inhibit one-half of the colour produced by the negative control. It is also used to calculate cross -reactivity values to similar compounds. The approximate Lower Limits of Detection (LDD) for the cross-reacting compounds.

Basic Test Procedure

• Extract the soil sample using the sample extraction kit
• Pipet Chlordane assay diluent into the antibody coated tubes, then add either calibrator or sample extract into the tubes
• Wait for 15 minutes
• Add Chlordane enzyme conjugate to the tubes
• Wait for five minutes, decant and wash the tubes
• Add substrate solution
• Wait for three minutes, add stop solution
• Read the absorbance using a photometer and interpret the results. (Refer to Chlordane Soil test kit instruction guide procedures)
• Stop the reaction and interpret results

Test kit components

• Assay diluent
• 20 antibody-coated test tubes
• Enzyme conjugate, substrate and stop solution reagents
• Calibrators for 20, 100 and 600 ppb Chlordane
• Negative control calibrator
• Test tube rack. and pipet tips
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight
• Portable spectrophotometer battery should be charged prior to use

Required test materials

• EnviroGard Chlordane in soil kit (7311000)
• Sample extraction kit (soil)(7311000EB)

Required test equipment

• Field soil lab (Accessory kit) (6050400) which includes: Repeating pipette*, Adjustable pipette*, Balance*, Repeating pipette tips*, Timer*
• Differential spectrophotometer - 110V (6000001), 220V (6000002)
• Field lab system rental (includes items marked with * above) (6997020)

Other recommended materials

• Latex gloves
• Absorbent paper for blotting test tubes
• Liquid and solid waste containers
• Calculator
• Tap or laboratory grade water for tube rinsing
• Marker pen

AZF686060 Microtox Acute Starter Pack by Modern Water

Only available with purchase of M500 analyser. Includes the following:

• 1 AZF686018 Microtox® Acute Reagent 10 vials
• 1 AZF686011 Microtox® Diluent
• 1 AZF686019 Microtox® Osmotic Adjusting Sol'n
• 2 AZF686016 Microtox® Reconstitution Solution
• 1 686005 Disposable Glass Cuvettes: 400x

SD50951 QuickChek Sulphate Reducing Bacteria RC II Economy-Pak (100) by Modern Water

The QuickChek™ SRB Detection System is a rapid enzyme immunoassay method that detects sulfate reducing bacteria (SRB). The test employs purified antibodies to detect the enzyme adenosine-5'-phosphosulfonate (APS) reductase which is common to all strains of SRB.

The purified antibodies are attached to small particles that selectively capture the APS reductase enzyme. The particles and captured enzyme are then isolated on a porous membrane, which forms a reactive layer that turns blue in the presence of the APS reductase enzyme.

QuickChek™ SRB offers several advantages over cell culture techniques for SRB detection including immediate and accurate results. The kit allows testing of solid and semi-solid samples and detects all SRB, including SRB that is unable to grow in some standard media. The test results are not compromised by chemical or salinity interferences that are often found in field samples.

The QuickChek™ SRB kit is completely self-contained and disposable. Each kit includes all necessary materials to detect and enumerate sulfate reducing bacteria. There is no need for pretreatment or dilution of samples and there are not special hazardous waste disposal limitations.

Features:

• Semi-quantitative results
• Detects all viable and nonviable SRB samples
• Results available in approximately 8-10 minutes
• Two or three samples simultaneously
• Detection limit of 103 cells/ml
• etection limit for "clean" waters down to 101 cells/ml

Applications

• Corrosion coupons
• Cutting fluids
• Drilling fluids (Muds)
• Solids: biofilms, sludge, rust, mud
• Water associated with oil

Warranty Plan includes annual calibration and cleaning, full parts and labour cover for failures (not those related to physical damage) plus shipping costs.

7540000 EnviroGard Microcystins Plate Kit by Modern Water

Envirogard® is a rapid laboratory enzyme immunoassay method for the analysis of water. It uses a plate technology to detect the analyte of concern.

Features:

• Rapid lab testing method for the detection of microcystins and nodularins in drinking and environmental water samples
• Conforms to ISO standards for environmental immunoassays such as ISO 15089
• Quantiative data results with excellent analytical precision
• Test up to 88 samples* at once for increased cost efficiency
• Results available in approximately 120 minutes
• Microtiter plate immunoassay
• Ideal for source water monitoring

Test result type

• Quantitative data

Samples per kit

• 96 well test kit (tests up to 88 samples*)

Assay range

• 0.1 ppb to 1.6 ppb
• Extended range available

Sampling time

• Sample-to-data in approximately 120 minutes

Specificity

The proprietary antibody used in this assay detects microcystins and nodularins. The crossreactivity of the Microcycstins EnviroGard® Plate Kit for various microcystin variants is shown below at 50% B/B₀

Basic Test Procedure

• Prepare standards
• Add 100 uL of sample or standard
• Incubate for 30 minutes
• Add 100 uL enzyme conjugate
• Incubate for 30 minutes
• Decant and wash five times
• Add 100 uL colour solution
• Incubate for 30 minutes
• Stop the reaction and read colour at 450nm

Test kit components

• Antibody coated microtiter plate strips, enzyme conjugate, colour development and stop reagent for analysis of 96 wells
• One vial each of 0.1, 0.2, 0.4, 0.56, 0.8 and 1.6 ppb microcystin-LR surrogate (nontoxic) calibrators
• Test kit instructions
• Optional 1.5 ppb check standard

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use for up to eight hours
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• Microcystins EnviroGard® plate (7540000)

Required test equipment

• 10 cc syringes
• 0.45 micron non-sterile filter units
• Pipette to deliver 100 mL
• Distilled or DI water for rinsing wells
• Microtiter plate reder or stip reader
• Timer
• Parafilm or tape
• Marker pen

Other recommended materials

• Orbital shaker
• Multi-channel pipette
• Repeater pipette
• Calculator
• Microtiter plate washer
• Solid extraction devices

Will last for approximately 1 box of reagent or 10 vials; nontoxic Ultra Pure Water; shelf life is one year at RT.