Bluelab Accessories / Spare Parts, Bluelab

803250 EC Shroud (for all Bluelab Conductivity Probes) by Bluelab

The 'Shroud' (found at the probe) is very important for the accuracy and protection of the meter.

The shroud carries out three crucial functions:

• Protects the probe tip from damage
• Slows the movement of the solution to get a more accurate reading
• The slots allow an even flow of solution to pass through to avoid air bubbles on the probe surface

The shroud is removed prior to the cleaning process.

DIBBER Replacement Dibber/Auger for Soil pH Probe by Bluelab

This handy dibber is used to pierce the soil prior to inserting the soil pH probe to eliminate the risk of sticks or stones breaking the glass tip of the soil probe.

There are units of measurement on the side, with centimeters and inches, so you can measure pH at consistent levels.

PUMPCASS-SM Cassette Only Small/Medium (10/100ml suitable) by Bluelab

The Bluelab Cassette is a replacement part specifically used with the Bluelab pH Controller, Bluelab pH Controller Connect, and Bluelab PeriPod M3 and M4.

Features

• Replacement peristaltic pump cassette
• Rollers and internal tubing included
• Simple to install
• Compatible with the Bluelab pH Controller and Bluelab PeriPod M3 or M4, suitable for 10/100ml pumps

METCARRYCASE Carry Case (Meter not included) by Bluelab

The Bluelab® Carry Case provides a custom fit so you can use and read your Bluelab® Meter right from the carry case.

A firm outer casing offers impact resistance for your Meter. There are two pockets in the top of the case specially made for the probes.

A removable and adjustable shoulder strap provides even more comfort and convenience. Simply zip up the Bluelab® Carry Case then tuck it away safely for storage or transport.

Note: Meter not included with case.

Features

• Firm outer casing for impact resistance
• Two custom pockets to insert Bluelab® Probes
• Internal strap to tuck probe cables away tidily
• Net pocket for Meter to sit in and strap to hold in place
• Strong nylon strap with adjustable length
• 'D' hook at top of outer case for hanging

Ideal for use with the following Bluelab Meters*

• Bluelab® Combo Meter
• Bluelab® pH Meter
• Bluelab® Soil pH Meter
• Bluelab® pH and Conductivity Pens

PHPROBECAP pH Probe - Screw Type Storage Cap by Bluelab

It is essential that the storage cap is placed back on the probe tip of the pH probe after use and when being stored. "If it dries it dies!"

Keep the pH probe tip wet by ensuring there is enough Bluelab pH Probe KCl Storage Solution to cover the probe

TRUNSHROUDV2 EC Shroud V2 - Twist type (for V02 Truncheon Meters only) by Bluelab

The 'Shroud' (found at the probe) is very important for the accuracy and protection of the meter.

The shroud carries out three crucial functions:

• Protects the probe tip from damage
• Slows the movement of the solution to get a more accurate reading
• The slots allow an even flow of solution to pass through to avoid air bubbles on the probe surface

The shroud is removed prior to the cleaning process.

PROEXBOX External Lockout/Alarm Box by Bluelab

Use to connect the Bluelab® Pro Controller™ to external switches, for example - a float switch or a greenhouse alarm system.

When these switches are activated, Bluelab® Pro Controller™ is placed in lockout mode, so no further dosing will occur until reset.

PROBHOLD pH Probe - Suction Cup / Holder by Bluelab

Protect your pH probe from damage by securing it with this nifty probe holder. Simply slide up the barrel of the probe stem and place onto the inside of a tank or reservoir.

As you know, pH probes are fragile as they have an internal glass stem and a glass bulb on the tip of the probe. A few dollars is all it takes to ensure a longer life from your pH probe.

POWERPODNA Powerpod by Bluelab

Electronic mains switching box designed to activate mains powered equipment. The Bluelab® PowerPod™ is an electronically controlled mains switching box that is designed to activate mains powered equipment via control signals from a Bluelab® controller.

The Bluelab® PowerPod™ is ideal for use when using a Bluelab® Pro Controller™ with third party mains powered pumps, heaters and coolers for temperature control.

Features

• 4 x IEC mains outputs (15A max inrush current)
• 100V~-240V~, 50/60Hz compatible
• Adds temperature control to Bluelab® Pro Controller and some Bluelab® Dosetronic™ models1
• Compatible with Bluelab® Pro Controller and Bluelab® Dosetronic™ models1

PWRSCONTPH pH Controller Power Supply by Bluelab

Use the international power supply pack with any Bluelab pH Controller or Pro Controller.

PWRSGUAR Guardian Monitor Power Supply by Bluelab

Use the international power supply pack with any Bluelab Guardian Monitor.

Power Out: 5V DC, 1Amp

PERILUBE Peridoser Tube Lube. 15cc Syringe by Bluelab

The tube lube is required for lubricating the tubing every six months and when replacing the tubing. It comes in a handy 15cc syringe for easy application.

It is a specialized silicone grease and is the only grease that can be used to lubricate the Peridoser Pumps.

SPOTKIT Sample Pot by Bluelab

Perfect for reservoirs located more than 2 meters / 3.3 feet from your controller unit.

Place probes directly into the chamber for direct measurement of nutrient solution. Fittings include

PERITUBE Peridoser Replacement Tubing 500mm by Bluelab

The Peridoser Tubing is replacement tubing for the Bluelab Peridoser pumps. It is easy to replace. No other types of tubing should be used. The tubing requires replacement approximately every 18 months to 2 years to ensure reliable performance.

The Peridoser Tubing is sold as pre-cut 500mm lengths (1.64 feet), the required length for each individual peridoser pump. One length is required per peridoser pump. For example; a Triple Peridoser requires three lengths, a Twin Peridoser requires two lengths and a Single Peridoser requires one length.