All Products

ADF25 Differential Probe by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

66-6201-05 T2A Sensor/Transmitter with j-box, Carbon Monoxide (CO), 0-500 ppm by RKI Instruments

The T2A Series toxic gas detector is a versatile assembly that uses an electrochemical sensor to detect a variety of gases. 2-Wire loop-powered to withstand extreme climatic conditions and harsh environments. Magnetic switches allow for nonintrusive calibration while in the field.

Features

• Electrochemical Sensor
• Loop-Powered (2-Wired), 4-20 mA output
• 3 Character, 7 segment display screen with backlight
• 3 Push-button interface (ADD, MENU, SUB) with corresponding magnetic, non-intrusive switches
• Operating temperature range -40°C to +55°C
• Aluminum device enclosure
• 303 Stainless-steel sensor housing
• 1-Year warranty

Industry Applications

• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Automotive
• Semiconductor plants
• Chemical plants

*Please note we can only ship RKI products to customers within the United States

SCT-108.002.30 SCT LEN LCD Digital Anemometer by ScichemTech

Includes:

• On/off
• H/T
• °F/°C
• 10 memories
• Air velocity unit
• Avg (multi point)
• Air flow volume measurement
• Avg/max/min reading

Features:

• A complete portable SCT meter for air / wind velocity and temperature measurements.
• Instant display of the air velocity and temperature
• Maximum, minimum and average value calculation
• Easy airflow volume calculation (CFM/CMM)
• 10 memories data storage/ recalling/clearing
• Data hold/test function
• One hour auto shut off function
• Battery operated with low battery indication.

72-0306RKA GX-2009 Personal Gas Monitor, 2 Gas O2 / CO with Alligator Clip, 12 VDC Charger & Vehicle Plug by RKI Instruments

Workplace safety is a top priority at RKI Industries. With a reputation as being a world leader in gas detection and sensor technology, the company invests heavily in their research and design team to develop the industry's leading workplace safety products. The GX-2009 Model Personal Four Gas Monitor utilizes advanced technology and efficient design. It is the world's smallest and lightest gas monitor.

The GX-2009 Model Personal Four Gas Monitor

The GX-2009 Model Personal Four Gas Monitor is an obvious choice for many particularly hazardous applications. From personal monitoring in confined spaces to its use in fire services and construction, the portable monitor has been rated intrinsically safe. Its noticeable alarm functions and simultaneous detection of four separate gases help to ensure the safety of workers in potentially dangerous situations. The state of the art monitor can detect LEL, O2, H2S, and CO simultaneously and display the results on the large LCD display screen.

Each of the miniature sensors are manufactured with the high quality control standards of RKI Instruments. The compact sensors utilize catalytic combustion, electrochemical, and galvanic sensor technology.

Alarm System

The unit features dual audible alarm ports at 95 dB, and three bright LED lights for noticeable alerts. The Personal Four Gas Monitor also utilizes an ultra strong vibration alert designed to notify users of atmospheric conditions even when the device cannot be heard. When the monitor is in alarm mode, the backlight on the LCD display is turned on. The multi-faceted alarm system is designed to be noticeable in any given situation and is sure to notify the user and those nearby.

Standard Features

The GX-2009 Model Personal Four Gas Monitor has many standard features including an incredible datalogging function. The datalogging software can store up to 100 calibration records and is compatible with many computer platforms. The log time can range from 10 to 300 hours and houses 8 alarm trends. The unit can also remind users of upcoming calibration and bump tests. With 2 glow in the dark, glove friendly buttons, users can easily operate the device on site.

The unit comes standard with an alligator clip, NiMH batteries, a charging station with VAC power supply, and a product CD with datalogging software.

Specifications

The GX-2009 Model Personal Four Gas Monitor is the smallest and lightest personal gas monitor in the world. Weighing in at less than 5 ounces, the device fits easily in the palm of a hand and is easily portable. Additionally, the IP-67 water resistant and dustproof design contains an impact resistant over mold rubber body to protect the integrity of the device. The unit uses a set of 2 NiMH batteries with 20 hours of operation. Each GX-2009 Model Personal Four Gas Monitor comes standard with a 2 year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

G450-11414K G450 Value Kit, Alkaline with Alkaline Smart Pump, O2, LEL, CO, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

Part Number: 66L-401

G460-11-10-16-00-24 G460 Multi-Gas Detector with Alkaline Smart Pump and NiMH Battery, O2, Catalytic Combustion LEL Sensor, SO2, NH3 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

6201-5142 IAM-100 Gas Detector, Remote Sensor/Faceplate, R407a 0-10,000ppm, 110 VAC by Bacharach

The IAM-100 Gas Monitor from Bacharach offers exceptional continuos monitoring performance and flexibility at an economical price. By itself, or integrated into a comprehensive detection system, the IAM-100 is a scalable solution for detecting a variety of refrigerants, combustible gases and VOC gas leaks at the lowest possible cost.

Onboard LEDs illuminate when the sensor is in an alarm state while the unit's audible alarm alerts personnel in the area that levels have exceeded the desired limit. The audible alarm can be muted with the onboard silence switch. Integrated dual relays enable the IAM-100 to shut-off refrigerant or propane supply lines while the second relay can be used as a connection to a building BMS or BAS system.

The IAM-100 is an alarm threshold device. When the range of the sensor is exceeded, the detector will go into alarm. For example, a unit with a 1,000 ppm R-410a sensor will activate its alarm when the detected refrigerant meets or exceeds 1,000 ppm.

Features & Benefits:

• Real-time continuous gas detection that's scalable, reliable and affordable
• Ideal for commercial applications such as hotel rooms, apartments, dorms, hospitals, restaurant kitchens or battery charging rooms
• Detects refrigerants (at ?1,000 or ?10,000 ppm), TVOCs (at ?1,000 ppm), combustible gases and hydrocarbons (at ?5,000 ppm)
• Fast-responding, long-life sensors
• Integrated visual LED and audible alarms
• Two onboard relays to activate shut-off valves, exhaust fans, or connect to a BMS or fire panel
• Remote sensor with aesthetic faceplate available for discreet monitoring in decorative interiors

Measuring Range: -40 to +600 °C

90080-06 Traceable® Thermometer with Clock, Humditiy Monitor and Calibration by Digi-Sense

Unique unit simultaneously displays time-of-day, temperature, and humidity. Clock displays AM/PM or 24-hour military time to the exact minute with 0.01% accuracy. Noting changes is easy with triple display. Internal sensors make it ideal for use in hoods, storerooms, clean rooms, incubators, drying chambers, and environmental cabinets. Temperature range is 32.0 to 122.0°F and 0.0 to 50.0°C. Resolution is 0.1° and accuracy is ±1°C. Relative humidity range is 20 to 90%. Resolution is 1% RH and accuracy is ±5% RH mid-range, otherwise 8%. At the touch of a button, memory recalls highest and lowest temperature and humidity readings. Permits monitoring conditions overnight, on weekends, or any time period.

Traceable® products are calibrated to NIST-traceable standards and ready to use as soon as you receive it. Each product goes through an intense vetting process before it can carry the Traceable name, and it includes NIST-traceable certification. This means that a 17025-accredited calibration test lab has confirmed that the product meets or exceeds all stated specifications, saving you both time and money by not having to calibrate separately.

NIST-traceable calibration also helps you meet quality standards and regulatory compliance for ISO, FDA, cGMP, VFC, CAP, CLIA and Joint Commission requirements.

• Get accurate, reliable measurements with included NIST-traceable calibration

Includes

NIST-traceable calibration certificate with data, AAA battery, built-in stand, and wall mount.

10204460 Altair 4XR Multigas Detector by MSA

Outfitted with rapid-response MSA XCell® sensors, the ALTAIR 4XR Gas Detector is the toughest 4-gas monitor on the market and is backed by a 4-year warranty. The ALTAIR 4XR can also provide real-time incident awareness to team members, supervisors, safety managers and others when paired with the MSA ALTAIR Connect app via a Bluetooth® wireless connection.

Real-time

• Sense gas 2 times faster than the industry average with our XCell sensors
• Quickly update MSA ALTAIR 4XR settings via the ALTAIR Connect app (available on the Google Play Store)
• Send event notifications via text message with the ALTAIR Connect app

Rugged

• Survives 25 drops from 4 feet (1.2 meters) (MIL-STD-810G drop protection)
• Can survive an incidental 25-foot (7.5-m) drop onto concrete
• Dust- and waterproof IP68 rating (2 meters for at least 1 hour)
• Operating temperature range: -40°F to +140°F (-40°C to +60°C)

Reliable

• 4-year instrument & sensor warranty
• Confirm compliance quickly with the Bump LED & on-screen checkmark
• Bump and calibrate with 1/2 the test gas and in 1/2 the time vs. industry average
• Bump and calibrate at a specified "Time of Day" with your MSA GALAXY® GX2 Automated Test System
• MotionAlert option tells others that user has become immobile
• User-activated InstantAlert notifies others of a potentially dangerous situation

61-0198RK-02 Sensor, IR Carbon Dioxide (CO2) 0-5,000 ppm, Non Explosion Proof Direct Connect, Replaceable Sensor by RKI Instruments

The RKI Direct Connect series gas sensors are highly reliable and very cost effective for the detection of common gas hazards. The direct connect series are available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and for a variety of toxic gases. The sensors for LEL, H2, Oxygen, H2S, CO2, and Carbon Monoxide are explosion-proof with flame arrestors, and approved for use in hazardous areas (Class 1, Div. 1 Groups B, C, D). An optional non-explosion proof version is available for oxygen, H2S, CO, and CO2 for use in non-hazardous atmospheres.

The Direct Connect sensors can be used in two different ways. The sensors can be mounted directly to the controllers as a complete stand alone system, or they can be mounted to explosion proof junction boxes for remote detection.

The toxic sensors are electrochemical type plug-in sensors, which provide high specificity, fast response, and long life. The plug-in design allows quick replacement in the field with no tools required. Toxic sensors are designed for use in Class I, Div. 2 hazardous locations. Sensors are available for NH3, SO2, PH3, AsH3, and HCN.

The Direct Connect sensors can be used either indoors or outdoors. The flame arrestors for the explosion-proof versions utilize a patented coating which make them water repellent. Also, splash guards are available for use in very wet environments. An optional stainless steel junction box is available for corrosive environments.

All of the Direct Connect sensors are designed to specifically interface with RKI Beacon 110, 200, and 410 controllers.

Features:

• Available gases include; LEL, H2S, CO, & CO2; Toxic sensors include NH3, AsH3, HCN, PH3, and SO2
• Infrared sensor for combustibles and CO2
• Patented water repellent sensor coating
• Explosion proof construction
• Optional stainless steel junction box

Applications:

• Petrochemical plants
• Refineries
• Gas plants
• Offshore drilling platforms
• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone, & electric utilities
• Parking garages
• Manufacturing facilities
• Steel
• Automotive

*Please note we can only ship RKI products to customers within the United States

VN00143 X-am 8000 Multi-Gas Detector, PID-HC,LEL,CO-LC/O2,H2S-LC,CO2 by Draeger

Clearance measurement was never this easy and convenient: The 1 to 7 gas detector detects toxic and flammable gases as well as vapors and oxygen all at once – either in pump or diffusion mode. Innovative signaling design and handy assistant functions ensure complete safety throughout the process.

Multi-gas detector

• 1- to 7 gas detection device
• for clearance measurement
• detection of toxic and combustible gases as well as vapors and oxygen

Specially designed for use with a pump, optimized for clearance measurement

The Draeger X-am® 8000 is equipped with a very powerful pump. It can be connected with hoses of up to 45 meters in length. A pump adapter makes it easy to switch between diffusion and pump mode at any time. This means the pump is only operated when you actually need it. That saves energy, reduces wear and tear, and extends the lifespan of the pump.

Handy and durable, the Draeger X-am® 8000 is intuitive to operate single-handedly using three function keys. The easy-to-read color display clearly lays out all the information for you.

The multi-gas detector also features advanced software functions including change of measurement gas for PID, CatEx and IR sensor during operation. This is based on an on-board library and a convenient assistant to hide unused sensor channels and adapt the flexible instrument to the measurement task.

Standard accessories include a sturdy shoulder strap so you can comfortably carry the X-am 8000. Thanks to its compact and robust construction, the device can withstand even the harshest conditions.

Clearance measurement, release and documentation in no time

The X-am 8000 effectively supports various applications with specially developed assistant functions that guide you through each process step by step. During clearance measurement, for example, the smart assistant calculates the necessary flooding time for the device and probe (FKM hose) based on parameters such as measuring gases, temperature limits, and the indicated hose length. Additionally, customer defined flooding times are also possible.

When monitoring for potentially high methane concentrations, an optional automatic measurement range switch makes it easier to take a reading: If the Cat-Ex sensor measures values above 100 % LEL, the display switches to the range of 0 to 100 vol %. A similar function to measure in % LEL and vol % simultaneously is also available for the IR EX ES sensor.

The DraegerSensor CatEx 125 PR Gas offers a special variant for the measuring gas methane, which enables measurements in the ppm range. The performance of selected sensors has been verified by an external approval body within the scope of the measurement performance approval (EN 60079-29-1) for combustible gases and vapors including methane, propane and n-nonane.

An additional useful tool is CSE Connect. It combines an app, specially designed for the X-am 8000, with a cloud-computing solution. Measuring jobs can be quickly and easily transferred to the app using an online application. An optional Bluetooth® module in the Draeger X-am 8000 enables measured values to be transferred automatically to the CSE Connect app. You can also easily and conveniently use the app to create measurement reports. This saves time and helps you manage your measuring tasks during clearance measurements more efficiently.

Clear signaling design

The signal system of the Draeger X-am 8000 is based on a clear color code, in accordance with the requirements of EN 60079-29-1, EN 45544-1 and EN 50104:

• Red light = gas alarm
• Yellow light = device-related alarm, e.g. low battery
• Green light = device is ready for use

The green glow of the D-Light allows you to see from a distance whether the device has been properly tested and is ready for use.

In case of an alarm, the X-am 8000 alerts you with colorful warning LEDs, a loud horn (100 dB(A) at a distance of 30 cm), and clearly palpable vibration. Optionally, four preset hazard symbols are available for the display which explicitly indicate the presence of explosive or toxic gas hazards, for example. This allows the user to easily recognize the type of hazard based purely on the symbol displayed.

The X-am 8000 is equipped with an impact detection system. The event report indicates whenever severe mechanical impacts have occurred that might result in functional impairments of the device or the sensors. These are also documented in the data logger. With this information, a device operator can specifically check the device. The instrument can also be locked after a detected impact as well.

Economical Fleet Management

Bumptest and calibration are carried out simply and quickly using the Draeger X-dock® calibrating station. Its low test gas consumption keeps operating costs to a minimum.

Its reporting function and numerous other useful features make the X-dock Manager PC software a smart addition to any fleet management operation. To identify devices in your fleet, you can either use tried and tested barcodes or an integrated RFID transponder.

Specialist for high and low hydrocarbon concentrations

To measure hard-to-detect hydrocarbons, you can fit the Draeger X-am 8000 with one of two high-performance PID sensors. The PID HC covers a measurement range of 0 to 2,000 ppm (isobutene). The PID LC ppb is particularly suited for a measurement range of 0 to 10 ppm (isobutene) with a high resolution in the range below 1 ppm.

For benzene-specific measurements, the X-am 8000 can be used with a pre-tube. The advantage: You only need one measuring device for this application, which significantly reduces the costs of purchasing, maintaining and transporting devices in use. The use of pre-tubes is supported by a built-in assistant.

Inductive charging protects against wear and tear

The X-am 8000 features inductive charging. This makes it easier to operate and increases the lifespan of the device. Issues like corrosion and contact problems in the charging cradle are a thing of the past. You can charge (outside of explosion-hazard zones) and measure at once, e.g, when using inside vehicles or on machinery.

The charging cradles can connect with one another, take up minimal space, and are compatible with existing Draeger X-am® series cradles.

6010MKA Handheld pH/ORP Meter Kit by Jenco

Includes:

• 6010M Handheld pH/ORP Meter
• 6000P 3-in-1 pH/ ATC Probe, 4-pin connector, Temp. 60º C
• 6003C Extension Cable, 4-Pin to BNC & 1-Pin ATC, 3-ft

• Simultaneous displays pH or mV and temperature.
• 50 data set reviewable memory (6010M only).
• Convenient calibration with automatic buffer recognition of US and European buffer sets. Calibration data is stored in memory and ready for use on power up.
• Automatic or manual temperature compensation.
• Automatic lock mode and end point sensing are available to lock in stable readings.
• Automatic shutoff function (30 minutes of non-use).
• Battery life over 1000 hours.
• IP65 waterproof
• Low battery indicator.
• RoHS and CE compliant.

6201-5140 IAM-100 Gas Detector, Remote Sensor/Faceplate, R134a 0-10,000ppm, 110 VAC by Bacharach

The IAM-100 Gas Monitor from Bacharach offers exceptional continuos monitoring performance and flexibility at an economical price. By itself, or integrated into a comprehensive detection system, the IAM-100 is a scalable solution for detecting a variety of refrigerants, combustible gases and VOC gas leaks at the lowest possible cost.

Onboard LEDs illuminate when the sensor is in an alarm state while the unit's audible alarm alerts personnel in the area that levels have exceeded the desired limit. The audible alarm can be muted with the onboard silence switch. Integrated dual relays enable the IAM-100 to shut-off refrigerant or propane supply lines while the second relay can be used as a connection to a building BMS or BAS system.

The IAM-100 is an alarm threshold device. When the range of the sensor is exceeded, the detector will go into alarm. For example, a unit with a 1,000 ppm R-410a sensor will activate its alarm when the detected refrigerant meets or exceeds 1,000 ppm.

Features & Benefits:

• Real-time continuous gas detection that's scalable, reliable and affordable
• Ideal for commercial applications such as hotel rooms, apartments, dorms, hospitals, restaurant kitchens or battery charging rooms
• Detects refrigerants (at ?1,000 or ?10,000 ppm), TVOCs (at ?1,000 ppm), combustible gases and hydrocarbons (at ?5,000 ppm)
• Fast-responding, long-life sensors
• Integrated visual LED and audible alarms
• Two onboard relays to activate shut-off valves, exhaust fans, or connect to a BMS or fire panel
• Remote sensor with aesthetic faceplate available for discreet monitoring in decorative interiors