All Products

Part Number: M5SS

1418-132K Micro IV Value Kit with 2-Years Sensor Warranty, Hydrogen (H2), 0 -0.04 vol. by GfG

Durable, compact design

Widest Range of sensors

Easy Operation

Up to six months of battery life

Clip-on attachment

Optional motorized pump

Large graphic display

Audible, vibrating and visual alarms

Lifetime warranty

DS220 docking station

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

Part Number: J197150LM20

Part Number: E1016500PM1

Part Number: X106725PM1

Part Number: 66L-252-5

2901-37-003 IR 29 Di Gas Transmitter with Rotatable Display, IP67, Propane (C3H8), 0 - 100 LEL by GfG

Measuring Principle

IR transmitters have become recognized as reliable gas warning systems for explosion protection. They are used to detect individual combustible gases or a wide range of gases. This involves sending an IR beam with a certain light intensity through a measuring space and then capturing it with a detector. Parts of this beam are absorbed by, amongst other things, hydrocarbon molecules. The reduced light intensity of the beam is registered by beam detectors and converted into a signal as the existing % LEL gas concentration.

Benefits

A special feature of our IR technology is its ability to also measure combustible gases above the lower explosion limit. Moreover, the measurement does not require oxygen.

With this technology there is basically no risk of contaminating the sensor, through silicone vapors or hydrogen sulfide, when using catalytic combustion sensors.

Operation

IR transmitters are usually used with 2 wavelengths, a so-called reference wavelength and just one measuring wavelength. Strict limits are applied to these systems. The absorption spectra of many hydrocarbons are located in the wavelength range of 3.3 μm and overlap to a large extent.

This means that gases with overlapping spectra and just one measuring wavelength can no longer be clearly distinguished. Some hydrocarbons, e.g. the frequently used welding gas acetylene, are non-absorbing in the wavelength range of 3.3 µm, but absorb instead in neighboring wavelength ranges.

In many practical applications, it is not essentially important which gas is responsible for the explosion risk. Therefore, early warnings through the broadband measurement of hydrocarbons in order to monitor the lower explosion limit (LEL) must be guaranteed. False alarms with uncritical concentrations of individual gases or solvents are thus absolutely unacceptable.

These requirements are problems for systems with 2 wavelengths.

Patented GfG Technology

The internationally patented technology of the IR 29 has been developed to solve these problems. The gold-plated mirror optics of the sensor contains 2 radiators and up to 4 detector elements with different optical filters. The precisely calculated, microstructured and pure gold coated mirror optics of the IR 29 are supplied for the first time without beam splitters.

This helps to cut signal losses by 50 % and to completely avoid the physically-related disadvantages of a beam splitter. The measured values from two additional wavelengths (4 wavelengths in total) ensure improved detection of individual gases and thus enhanced selectivity. This results in the prevention of false alarms. Only a 4 wavelength system always guarantees early warnings and the simultaneous prevention of false alarms.

New Technology

The IR 29 is the first and only intrinsically safe IR gas transmitter with patented 4-beam 4-wavelength technology.

The ignition protection class "intrinsically safe", which is so essential for industrial plants and the mining industry, is achieved by the additional use of the SB1 safety barrier and its internationally patented and innovative design.

Complete Safety Even In Zone 0

The IR 29 is the first IR gas transmitter that can also be used in Ex zone 0 and which enables maintenance as well as replacement of the sensor head without additional expense when energized.

Universal Application

The IR 29 with its robust V4A stainless steel housing has been designed to withstand the harshest environmental conditions.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Internal Data Logger

A standard built-in data logger records all the measuring data, minimum / maximum values, average values and alarm events of the last 24 hours in a ring buffer.

The recording can also be shown on the display as a 2 and 8 hour trend indicator.

The histogram mode can be selected as a permanent display of the measured values. These values are continuously updated.

Graphical Display

Measured values are shown on the high-contrast graphical display. The display can be rotated 180° depending on the installation of the IR 29.

Self Diagnosis

Processor-based signal processing enables the systematic compensation of temperature dependencies, aging influences and soiling effects. Safety-relevant functions are monitored permanently via self-diagnosis procedures and a possibly required service is indicated automatically. Daily interfering factors, such as dust and dirt accumulation, are almost completely eliminated by the innovative design.

Pressure Sensor, Moisture and Temperature Compensation

The measuring accuracy of IR sensors depends on partial pressure and thus also air pressure. Climatic fluctuations or barometric high pressure therefore influence the measuring result. Furthermore, the absorption spectrum of water almost completely covers that of hydrocarbon absorption in the 2.7 to 3.3 μm range. Air humidity therefore initially generates a measuring signal the same as the actual measuring gas. This cross-sensitivity is of particular importance in warm areas with high relative humidity. An increase in the absolute water absorption capacity of air is not linear with the temperature, i.e. three times as much water can be absorbed at 40 °C than at 20 °C. This influence can only be compensated if the current moisture content of the air is known. The IR 29 can be optionally equipped with a pressure and moisture sensor for compensation.

Maximum Safety

The innovative display enables the realization of completely safe warning concepts.

Local displays and signals directly at the device can be used to provide an early warning of potential risks.

The display at the upstream safety barrier SB1 D enables the detection of risks outside the danger zone being monitored.

This allows immediate on-site action before really hazardous situations occur.

Dust Protection

A gas permeable, water-repellent diaphragm protects the absorption space of the transmitter against dust. The additional impact protection made from robust V4A stainless steel prevents mechanical damage to the optical components.

The diaphragm can be cleaned or replaced in a matter of minutes.

Remote Controls

The IR 29 transmitter does not feature control elements for setting or servicing tasks. This helps to prevent accidental or unauthorized manipulation.

Service work at the IR 29 transmitter is carried out using the RC 2 remote control.

Features

• First intrinsically safe infrared transmitter for explosion protection
• ATEX II 1G Ex ia IIC T4 Ga C0158 can also be used in Ex zone 0
• Temperature, moisture and pressure compensation
• Patented infrared technology (NDIR)
• The energized IR sensor head can be replaced in Ex areas
• Maintenance and service-friendly

72-0010-56 OX-03 Single Gas Personal Monitor Kit with Alkaline Batteries, Screwdriver, Case and Calibration Kit (34L Cyl 100% N2, Regulator, Cal Cup & Tubing) by RKI Instruments

Individuals need personal protection in hazardous areas at all times without adding extra bulky equipment, and the 03 Series can provide that kind of protection at an affordable price. The GP-03, OX-03, CO-03, and HS-03 models are personal single gas monitors designed for protection from exposure to combustible hydrocarbons, oxygen deficiency, hydrogen sulfide, or carbon monoxide.

The O2, CO, and H2S versions can be operated continuously for at least 3,000 hours on (2) AAA size alkaline batteries. The GP-03 operates for 35 hours on alkaline and 30 hours on rechargeable Ni-MH. The 03 models have 2 preset alarms that are user adjustable. Each version is also equipped with visual, audible, and vibration alarms as standard.

The replacement sensors are inexpensive, easily field replaceable, and are interchangeable with other popular RKI instruments like the GX-2009, GX-2012, and GasWatch 2. Sensors for LEL and O2 have a life expectancy of over 2 years. Sensors for H2S and CO have a life expectancy of over 3 years.

Each 03 Series monitor is impact, dust, and water resistant with an IP-67 rating. 03 Series instruments are safe for use in hazardous locations, classified as intrinsically safe ATEX/IECEx and by CSA to U.S. and Canadian standards (pending) for Class I, Division 1, Groups A, B, C, and D atmospheres.

Features:

• Operates 3,000 hours on alkaline (GP-03 operates 35 or 30 hrs on alkaline/Ni-MH)
• Pocket size 2.1"(W) x 2.6"(H) x 0.9"(D)
• Light weight 2.8 ounces
• Impact, dust, and water resistant (IP-67)
• Replaceable rubber boot
• Data log 5 to 300 hours with adjustable intervals
• Audible / visual / vibration alarms
• Automatic backlight
• Peak Hold, STEL & TWA
• Low battery alarm
• Intrinsically safe, ATEX (CSA pending)
• 3 Year warranty H2S & CO
• 2 Year warranty LEL & O2

Applications:

• Hazardous material
• Mining
• Refineries / petrochemical
• Water / wastewater treatment
• Pharmaceuticals
• Utilities
• Chemical plants
• Fire services

*Please note we can only ship RKI products to customers within the United States

Part Number: M1016200PA

Part Number: X105325PM37

Part Number: 44L-125-25

Part Number: SPHF1

2109-200 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 200 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

Part Number: E197150LM20

Part Number: SPCPROB114

2113400 UV Spectacles by AquaPhoenix

Protect eyes from extended or high-intensity ultraviolet energy while eliminating "blue haze" interference. Light weight and comfortable, even over prescription glasses.

73-0051RK-NH3 SC-01 Single Toxic Gas Monitor, Ammonia (NH3), 0 - 75 PPM, with Belt Clip by RKI Instruments

Paving the way for gas detection and monitoring solutions, RKI Instruments produces the most advanced sensors and monitors. Their teams of experts are constantly seeking new and innovative methods for meeting the unique needs of jobsites with potentially hazardous conditions. Integrating the latest smart sensor technology with functional design, RKI Instruments is proud to present the SC-01 Model for single toxic gas monitoring.

SC-01 Model Single Toxic Gas Monitor

The SC-01 Single Toxic Gas Monitor is the latest in smart sensor technology with practical applications in refineries, chemical plants, hazmat response, semiconductor plants, and more. It is a versatile single gas detector with interchangeable sensors. The unit automatically recognizes when a sensor has been changed and automatically calibrates to the recognized sensor. The internal technology stores each sensor's configuration and activates the data once the new sensor is recognized.

What sets the SC-01 apart from its competitors is its wide range of available ESM-01 sensors including unique sensors for arsine, ammonia, carbon monoxide, chlorine, hydrogen cyanide, hydrogen sulfide, phosphine, and sulfur dioxide. These plug in style sensors are easy to change and can be replaced quickly while onsite. Onsite workers can also utilize the optional 10 foot extender cable for remote monitoring and quick response.

Exclusive Features

The SC-01's large backlit LCD display is great for onsite use and is easy to read. The screen displays the gas reading, battery level, and current time. When the alarm is activated, the LCD screen's backlight automatically activates. The alarm features a quadruple notification system that includes a buzzing audible alarm, a blinking LED display, a vibration alert, and display indicator. The unit performs regular safety self-evaluations for sensor connections, battery life, and circuit issues. Amazingly, the unit can function with more than 250 hours of continuous operation with 2 AA alkaline batteries. The SC-01 comes standard with data logging capabilities ensuring that workplace safety managers are able to monitor, record, and evaluate possible hazard trends.

SC-01 Model Specifications

The unit is highly portable with its lightweight (less than 8 ounces) and pocket size dimensions (2.6 x 6.2 x 1.2 ). Users can easily control the unit's functioning with its 3 large front facing push buttons. The casing is designed to protect the monitor with its high impact plastic with rubber boot that is dust proof and splash proof. The typical response time for gas detection is approximately 60 seconds and uses electrochemical detection. For gas monitoring needs, the SC-01 Model is rated intrinsically safe.

The SC-01 Single Toxic Gas Monitor comes standard with several accessories for easy use including an alligator clip, AA alkaline batteries, impact resistant rubber boot, and a user manual. Users can also purchase optional accessories to further customize the unit to meet specific workplace needs. These optional accessories include a belt clip, a 10 foot extender cable, and datalogging software that is PC compatible.

*Please note we can only ship RKI products to customers within the United States

Xgard Gas Detectors

Crowcon is a global leader in designing and manufacturing gas detection technology and equipment. The company has been in operation for over 40 years and is consistently building upon its products. By integrating modern technology with the demands of the modern workplace, Crowcon has developed a line of gas detection devices and monitors that lead the competition. The Xgard range of gas detectors is a product of Crowcon s successful integration and technological advancements. With a wide range of sensor types and available accessories, the Xgard series is suitable for all worksites and is customizable enough to fit any needs.

Tough and reliable

The Xgard series of fixed point gas detectors is incredibly durable and reliable. The casings and materials, including weatherproof caps, are designed to protect the equipment from the harshest environments. The detectors are made from a variety of materials depending on the model: glass reinforced nylon, aluminum with polyester coating, and 316 stainless steel.

Variety of sensors

The fixed point gas detector offers a wide range of sensors for to suite almost all applications. The Xgard range of gas detectors is available in three models to meet varying worksite needs: flameproof, intrinsically safe, and safe area formats. Additionally, Xgard offers different types of fixed point gas detectors within these three models:

• Xgard Type 1- Intrinsically safe toxic and oxygen gas detectors
• Xgard Type 2- Flameproof toxic and oxygen gas detectors
• Xgard Type 3- Flameproof flammable gas detector
• Xgard Type 4- Flameproof high temperature flammable gas detector
• Xgard Type 5- Flameproof flammable gas detector with 4-20mA output
• Xgard Type 6- Flameproof thermal conductivity type gas detector
• Xsafe- Safe area flammable gas detector

Cost efficient and highly effective

With quick and easy installation and maintenance, the Xgard series is able to keep costs at a minimum. The replacement sensors, for example, are simple to replace by merely plugging them in. The replacement parts are also readily available and compatible with all Xgard models, thereby reducing the amount of required spare parts that are stored in the facility. Additionally, the sensors have two times the typical life spans of similar sensors in the industry. With a 2 year life span, worksites can expect to cut their sensor replacement costs in half. For worksites that require slightly more customization, Crowcon offers compatible accessories for the Xgard series such as sampling applications, remote gassing applications, spray deflectors, sun shields, weatherproof caps, collector cones, flow adapter, and accessories adapter.

Xgard also has flexible installation options. The unit is designed for either wall or ceiling mounts, and users will not need to purchase additional equipment for mounting. For more complex installation needs, users can purchase accessories.

Specifications

Each model is approximately the same size with dimensions of 6.1 x 6.5 x 4.3 inches and weighing approximately 1 or 2 pounds. The battery type, electrical output, and power requirements vary based on the sensor type. For a complete listing of gas sensors, types, and individual specifications, please see the product specifications listing.

YD300 Portable Water Hardness Meter Kit by Apera

The Apera Instruments' YD300 is designed for quick & accurate measurements of Water Hardness (the concentration of calcium ions Ca2+ and magnesium ions Mg2+). The YD300 comes equipped with a patented 601 water hardness combination electrode that is proven to produce the same accuracy as the traditional EDTA Volumetric Method but in a much more convenient manner. Unlike the traditional EDTA Method, There is no need for probe stirring or adding reagents during tests, and you can directly measure your sample solutions' ion concentration just like pH testing.

The meter utilizes an intelligent chip design that supports automatic calibration, data storage (up to 99 groups) and a low battery voltage indicator. The YD300 supports the ability to switch between eight commonly used Water Hardness units, including mmol/L, mg/L (CaCO3), mg/L (CaO), mmol/L (Boiler), mg/L (Ca), °fH (France Degree), °dH (German Degree) and °eH (England Degree).

The YD300 is IP57 waterproof rated and comes as a complete kit. This kit includes the Model 601-S water hardness electrode, Water hardness calibration solutions ( B1, B2 and B3 ); corresponding calibration bottles, Water hardness activation solution, a 20 ml test cup, a test cup pedestal, 2 AA batteries, and a quick manual all in a rugged carrying case. Applications: drinking water, wastewaters, cooling towers, boilers, pipelines, aquaculture, pools & spas. Two-Year manufacturer warranty for the instrument (6-month for the probe).

• Adopting electrode method to test hardness, having the same accuracy as EDTA titration method, yet much more convenient
• Patented 601-S 3-in-1 water hardness combination electrode: combines a measuring electrode, a reference electrode, and a temperature electrode all in one
• Intelligent chip design produces stable potential, fast response rate, and convenient use;
• 99 groups of data storage; automatic calibration and temperature compensation (ATC), auto-lock and power-off
• Portable IP57 waterproof design equipped as a full kit with a rugged carrying case; suitable for both lab and field test