All Products

72-5554RK-03 Eagle Portable Monitor, LEL / Oxy / CO / H2S (0-1.00 ppm) / CO2 (0-5%) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

Part Number: 17L-333

MISC-MP2BEF-WUVIR-o2 MiScope Megapixel Digital Microscope Extended Field with White, UV and IR LEDs by Zarbeco

The 2 megapixel extended field of view MiScope digital microscope offers a wider field of view with high resolution optical zoom and 2 micron resolution at maximum magnification.

The MiScope Megapixel 2EF takes the compact design of the MiScope and doubles the zoom ratio. An extended field of view (over 3 inches) provides 5 - 124x magnification, allowing you to see an entire signature and still zoom in for up to 120x magnification.

The higher resolution optics and 2 megapixel camera produce improved image quality, with resolution down to 2 microns. The MiScope Megapixel 2EF includes a switch to turn off the built-in LED lights. With the lights off, the MiScope Megapixel 2EF can be used on a light table, or with external lights for advanced lighting techniques.

The MiScope Megapixel 2EF includes our Video ToolBox PRO PC software, which adds enhanced measurement tools, a live on-screen reticle (or grid), and picture-in-picture freeze frame. It still allows you to capture still or moving images. You can also add labels, markers, time stamps, or draw on and make measurements directly on the live image.

An optional stand lets you position the MiScope-MP2 at the best location for large field-of-view imaging.

Features

• View live and capture images on the computer screen (or use a computer projector for large groups)
• 5- 124x magnification
• Completely portable with a laptop computer
• Save still images, movies and time lapse
• Labels, markers, time stamps, measurement, picture-in-picture
• Draw directly on the live image
• Video ToolBox PRO PC Software with enhanced measurement tools (Video ToolBox Premier Optional)
• Includes stacking shims for magnification

Application

• Education
• Field Science
• Collectibles
• Forensic Science
• Manufacturing
• Entomology

Computer Requirements

• Pentium IV 1.8 GHz or greater (or Core Duo 1.6+ GHz)
• Windows XP/7/8/10
• Mac OS X 10.6 or better (Mac Software Optional)
• Video card with 32MB+ memory
• DirectX 8.1 or greater
• Internet Explorer 5.0 or greater
• USB 2.0 port

81-SDM3R304 SDM-3R Calibration Station with 3 Solenoids, Demand Flow Regulator, 34AL Cylinder H2S/CO/CH4/O2, Cylinder Holder, AC Adapter, Flash Drive, USB Cable, and Tubing by RKI Instruments

Stand Alone Use

The SDM-3R is a versatile maintenance tool that automates the service of a GX-3R (Pro) portable gas monitor. This docking station can be used as a stand alone device for charging, calibration and bump testing, with all records stored automatically for future upload to a PC via USB flash drive (PC software and flash drive included).

PC-Controlled Use

Automate how you manage and service GX-3R (Pro) instruments by connecting the SDM-3R to a computer with a USB cable. With the SDM Docking Station controller software, you can simultaneously calibrate, bump test, alarm check, archive data, or charge up to ten instruments. You can also download the datalogging history from each instrument into one easy to manage location. SDM-3R stations can be manifolded together to reduce the number of demand flow regulators gas cylinders required.

Features of Stand Alone Use (no PC required)

• Compatible with both GX-3R and GX-3R Pro
• Automatically charge, bump test, and/or calibrate
• Auto on/off of gas detector
• 3 separate gas inputs
• Multiple modules (10 max) can use one set of calibration equipment
• Save Bump Test, Calibration, and Alarm Check records to USB flash drive, computer, or network
• Includes PC software for viewing/archiving bump test, calibration records, and event data

Features of PC-Controlled Use

• Multiple modules connected to a PC (10 max)
• Automatic calibration/bump test option
• Configure GX-3R (Pro) parameters
• Archive Bump Test, Calibration, and Alarm Check
• Archive data to network location
• Software controlled data retrieval
• Windows 7, 8, and 10 compatible

*Please note we can only ship RKI products to customers within the United States

MCX3-XU00-Y-NA GasAlertMicroClip X3 2-Gas Detector, Combustible (% LEL, Unfiltered), Oxygen (O2) - Yellow Housing, NA version (North America) by BW Technologies

With that combination of benefits, it's no wonder the GasAlertMicroClip is the world's most popular multi-gas detector, serving as your trusted companion in hazardous environments - keeping you safe without weighing you down.

Plus, it's the first multi-gas detector with a rating of IP68 for unmatched water protection. So you can be confident it will stand up to challenging conditions.

Choose from two detectors, both with extended 18-hour battery runtime, one-button operation and Honeywell's rigorous approach to quality:

GasAlertMicroClip XL: low up-front cost with a two-year warranty.

GasAlertMicroClip X3: three-year warranty and a new oxygen sensor that extends overall operational life expectancy.

Use our unique advanced technology for safety, compliance and productivity.

• Advanced engineering for reliable battery performance
• Reflex Technology™ automated self-test function routinely checks the operating condition of the sensors to increase safety, up-time, and overall worker confidence
• Compact, lightweight and easy to use - no expertise required
• Flashing green IntelliFlash™ light for compliance at a glance

GasAlertMicroClip Standard Features:

• Guaranteed runtime for at least a 12-hour shift - down to -20°C - without compromising LEL detection of hydrogen, acetylene and other combustible gases
• Durable, rechargeable lithium polymer battery - tested to last in extreme environments
• Ergonomic and wearable - doesn't weigh you down
• Real-time gas concentrations shown on LCD
• Bright, wide-angle visual alarm bars
• IP68 rating ensures maximum protection against dust and water
• User-friendly, tamper-proof operation with just one button and intuitive LCD icons
• IntelliFlash™ light indicating detector has been bump tested and is monitoring correctly
• Self-test of sensors, battery status, circuit integrity and audible/visual alarms on startup
• Compatible with MicroDock II docking station for automated bump tests and calibration
• Compatible with Fleet Manager II software for reporting and fleet management
• Multi-language support in English, French, German, Spanish and Portuguese

New to GasAlertMicroClip X3:

• Five-year life expectancy - plus a three-year warranty
• An all-new oxygen sensor that operates consistently for five years - with no replacement costs for the life of the detector
• Superior cost of ownership - with minimized maintenance and maximized uptime

Part Number: MCX3-XU00-Y-NA

SS4-AS2-CSS-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

Part Number: 10L-355

G222E-0720 G222E Dual sensor configuration - 2-year Oxygen (O2) and Hydrogen cyanide (HCN) (50 ppm) - Instrument Only by GfG

Sturdy and compact dual gas detector for monitoring toxic gases, H2 and O2

The G222E is the first device in GfG s Micro 5 series. At present, it is the smallest and at the same time one of the lightest one- to two-gas detectors with two electrochemical gas sensors (EC) in the world.

Safety through quality and functionality

Equipped with high-quality, precise and durable sensors, the system is individually tailored to your requirements. Currently, sensors are available for 20 different gases and a wide array of measuring ranges. Combine them according to your requirements or increase the safety of your employees even further by redundant use of the same sensors to minimize the danger from a specific gas.

A simple, two-button menu and a large, easy-to-read display provide easy menu navigation and reliable information even under difficult conditions.

Suitable for long periods of use

Depending on sensor equipment and configuration, the G222E has an average operating time of up to 9 months at 10 hours per working day or 90 days in 24/7 operation. The battery of the G222E can be changed in seconds if necessary and the gas detector is ready for use again.

Data logger

The internal data logger stores the last 2600 events. These include measured values, alarms, TWA and STEL values, and time as well as temperature information.

Calibration Cap & Smart Cap

Calibration and adjustment of the G222E are quite simple. All you need is the Calibration Cap for manual zero and test gas application.

If you want to read out the content of the data logger, you will need the Smart Cap, a USB connection cable and the Config Software for the G222 series instead.

0560 8650 865 - Thermal Imaging Camera (integrated testo SuperResolution, Lithium ion rechargeable battery) by Testo

The testo 865 thermal imager offers professional technology and concentrates on functions which are needed in a contractor's daily work. The testo 865 is a user-friendly thermal imager, optimized for fast and efficient work. With the testo ScaleAssist functions ensuring optimum setting of the thermal image scale for building thermography and the IFOV warner making sure you avoid measurement errors, you will always generate the perfect infrared image.

Areas of application of the testo 865 thermal imager

Detect leaks, identify overheated connections, pinpoint thermal bridges or detect structural defects. The testo 865 thermal imager is ideal for applications in daily maintenance and installation work in trade and industry. It enables time-saving quality assurance and ensures reliable production control.

• Very good image quality due to high resolution: 19,200 temperature measuring points ensure precise thermography. Infrared resolution of 160 x 120 pixels – via integrated SuperResolution Technology 320 x 240 pixels
• Visualize temperature differences from 0.12°C
• Critical temperature conditions are directly displayed via automatic hot-cold spot recognition
• The IFOV warner means the distance from the measurement object / measurement spot size is determined and the measurement spot is shown on the thermal image – you therefore avoid measurement errors because the camera shows you exactly what you can measure
• Pro software for image evaluation on the PC
• You can choose to save thermal images as JPEGs

Includes:

testo 865 thermal imager, including USB cable, mains unit, lithium-ion rechargeable battery, IRSoft professional software (free download), commissioning instructions, short instructions, calibration protocol and case.

*Please note we can only ship RKI products to customers within the United States

IL-250 Test Strips: Lo Iodine, 0-12.5-25-50 ppm by AquaPhoenix

Lo Iodine Test Kit, 0-12.5-25-50 ppm / The Hydrion Lo Iodine Kit provides an easy way to estimate the amount of titratable iodine in sanitizing solutions made with commercial iodophors. The color chart is easy to read and has color matches at 0-12.5-25-50ppm(parts per million) of titratable iodine., Each kit contains one 15-foot roll of iodine test paper, matching color chart, and two sample tubes with caps. In addition there is one extra roll of iodine test paper and a laminated color chart. Provides for approximately 200 tests.

Part Number: 10L-389-35

12" Poly Blade, 6-Wing

2901-43-009 IR 29 e DB (Increased Safety) Transmitter with Pressure & Humidity Compensation, IP 67, Acetylene (C₂H₂) Triple Beam, 0 - 100% LEL Range, Display / Modbus by GfG

Unlike traditional LEL sensors, IR 29 transmitters do not need the presence of oxygen to detect gas. Since they are not affected by sensor poisons they don't require periodic adjustment to make up for lost sensitivity. The IR 29 continuously monitors its functions for proper performance, and can even identify and communicate required service procedures.

Features

• ATEX: II II 2G Ex eb mb ib [ib] IIC T4 Gb
• Patented infrared technology (NDIR)
• Temperature, moisture and pressure compensation
• Maintenance and service-friendly
• 4-20 mA, linear or digital (Modbus interface)

724-052 Eagle 2 Portable Monitor for LEL & PPM/O2/CO/HCN by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

Part Number: E10161000PM4