All Products

65-2480RK-05 Multi-sensor, Direct Connection for LEL (Catalytic)/H2S/CO with J-Box, CSA Version by RKI Instruments

The RKI direct connect series gas sensors are highly reliable and very cost effective for the detection of common gas hazards. The direct connect series are available for LEL, Oxygen, H2S, and CO for a variety of RKI's controllers. All sensors are explosion-proof with flame arrestors, and approved for use in hazardous locations.

The tri-sensor head can be used either indoors or outdoors. The flame arrestors for the explosion-proof versions utilize a patented coating which make them water repellent. Also, splash guards are available for use in very wet environments.

The unique tri-sensor design integrates 3 sensors into one explosion proof housing. This results in significant savings with installation and wiring cost versus traditional single sensor enclosures. Only one conduit needs to be run to the sensors.

The tri-sensor head is designed to exclusively interface with the RKI Beacon 410 controller. This 3 sensor head, used with the Beacon 410, is especially well suited for wastewater applications.

Also available in a two or four sensor version, with sensors for LEL, Oxygen, H2S, and CO available.

IR (infrared) sensor versions available for LEL detection.

Features:

• 3 Sensors, 1 explosion proof housing
• Infrared sensors available for combustible gases
• Interfaces with Beacon 410 controller
• Available for LEL, O2, H2S and CO
• Water repellent patented sensor coating
• Long life sensors (2 + years typical)
• Also available with 2 or 4 sensors

Applications:

• Wet Wells
• Dry Wells
• Bar Screen
• Lift Station
• Digesters
• Thickeners
• Primary Clarifiers
• Pump Stations
• Confined Spaces

*Please note we can only ship RKI products to customers within the United States

5601-3051 GDX-350 Gas Sensor Transmitter/Monitor, [NH3] 0-500 ppm, 2-wire by Bacharach

Bacharach's new state-of-the-art GDX-350 transmitters, with Smart Sensor technology, provide accurate and continuous detection of toxic, combustible and asphyxiate gases. The full-featured design of the GDX-350 includes a large LCD display, a 4-20 mA interface, programmable alarms, optional relays and a Modbus interface. Exclusive pre-calibrated replacement sensor technology makes occasional maintenance practically effortless. Rugged construction, intrinsic safety capability (in two-wire mode with barrier) and an explosion-proof housing allow the GDX-350 to operate directly in hazardous-rated areas of many industrial environments, delivering reliable, superior-sensing performance to protect human life, equipment and property.

With its large LCD display, the GDX-350 shows gas concentrations, engineering units and bar graphs along with the most recent 30 minutes of trend data. Utilizing the on-board magnetic keypad, users can also navigate through the display to change alarm set points, instrument configurations, or enter into maintenance mode for non-intrusive sensor calibration. For security, menu options also enable the selection of an authorization code to lock critical parameters. Accompanying the LCD display are standard LED alarm indicators that show when low and high alarm conditions are met. An optional relay board is available to provide three 5-amp relays that can be used to drive audible/visual alarms, or activate exhaust fans.

Features & Benefits:

• Pre-calibrated Smart Sensor capability with 'plug-n-play' convenience minimizes maintenance and downtime
• Non-Dispersive Infrared (NDIR), Catalytic Bead and Electrochemical sensor options available
• Can be placed directly in hazardous environments where leaks occur for quick detection and rapid response
• Graphic LCD for real-time monitoring of concentrations
• 4-20 mA, optional Modbus RTU® and wireless interface
• Easily update alarm set points, configurations or maintenance modes using the LCD display
• 30-minute onboard data trend

G02-B024-000 ToxiRAE Pro PID Personal Monitor - 9.8 eV PID Lamp, Datalogging, Wireless, Rechargeable Battery, Rubber Boot by RAE Systems

The ToxiRAE Pro PID is the world's smallest volatile organic compound (VOC) monitor. Featuring RAE Systems' next-generation PID sensor, the ToxiRAE Pro PID can quickly detect and accurately monitor over 300 VOCs. The ToxiRAE Pro PID provides safety professionals wireless remote access to real-time instrument readings and alarm status for better visibility and faster incident response. With an onboard library of 190 correction factors, the ToxiRAE Pro PID can be programmed to automatically read in equivalent units of the specified compound.

ToxiRAE Pro PID comes with

• ToxiRAE Pro PID monitor with sensor and wireless option as specified, rechargeable battery, alligator clip, and protective rubber boot installed
• Charging and PC communication cradle
• PC communication cable
• AC adapter (100 to 240 V, 50/60 Hz AC to 12 V DC)
• Calibration adapter
• Combined instrument / sensor cap removal tool
• Quick Start Guide
• CD with documentation
• CD with ProRAE Studio II monitor configuration & data management software
• Technical Note TN-106 with ionization energies and correction factors for 300+ VOCs (Industrial Hygiene versions only)
• Calibration and test certificate
• Warranty/registration card

Key Features

• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Largest display in its class
• Continuous datalogging
• On-board correction factor library for 190 compounds
• Easy to use
• Reliable, rugged, and intrinsically safe

Applications for Industrial hygiene and safety

• Chemical plants
• Government health, Safety, Security, and environmental agencies
• Hazardous materials teams, first responders
• Oil and gas
• Pharmaceutical plants

Applications for Environmental applications

• Environmental consulting
• Soil remediation

72-5477RK-03 Eagle Portable Monitor for LEL/O2/O3/CO2 (0 - 5%), (No Probe) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

Part Number: 116L-SIH4-5

621C3 Dual Input Differential Manometer Kit by Test Products International

Differential input high resolution manometer with A612 protective boot, two A603 1/8" barbed NPT fittings, two A605 1/8" barbed T fittings, two A776 static tips, and A908 carrying case with shoulder strap.

The TPI 621C3 is a hand held pressure meter with superior resolution.

All of these models measure over the range of -40.0 to +120.0 mbar. Each unit has a resolution of 0.01 mbar to +19.00 mbar and automatically auto-ranges above ± 19.00 mbar to 0.1 mbar resolution. Each model is supplied complete with carry pouch, battery and instruction manual.

The 621C3 includes all of the specs of the Model 621 and additionally consists of the following:

• 621 Manometer: + A612 Boot with tilt stand
• A605 T Fitting (x2): Ideal for use on setting pressure switches
• A776 Static Tip (x2): Measure static pressure with A776. It has a magnet to secure in place in duct work 1/4" hole required to use
• A774 Tubing: 6 foot length of silicone tubing for pressure measurements. Very flexible and will not go hard in cold temperatures.
• A791 Adapter Tube: Flexible tubing for connecting to larger fittings
• A908 Carrying Case: Soft padded case with shoulder strap holds the thermometer and probes.

*Please note we can only ship RKI products to customers within the United States

C66 Waterproof Conductivity Tester with Replaceable Electrode (high range) by Milwaukee

The C66 is a conductivity IP65 waterproof tester, specifically designed for the hydroponics and Agricultural markets, with automatic temperature compensation and 1 point manual calibration. The tester has a range of 0.00 to 10.00 mS/cm.

The C66 has a replaceable electrode and is supplied in a casing with calibration solution sachets (M10031) and screwdriver for calibration. The modular design allows easy electrode and battery replacement.

72-5608RK-01 Eagle Portable Monitor for LEL/O2/H2S/CO/NH3/CO2 (0 - 5,000 ppm) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

GD-K71D-CLF3 GD-K71D Smart Transmitter, Chlorine Trifluoride (ClF3), 0 - 0.6 ppm by RKI Instruments

The GD-K71D is a complete sample drawing gas monitor, including digital readout and alarm relays. A new gas sensor technology using an intelligent sensor for remote location calibration and setup is used. The new GD-K71D sensors are designed to provide a longer time period between calibrations. Calibration intervals have been extended to12 months of on-line service which equates to reduced maintenance cost. In addition, the sensors can be calibrated away from the gas detector installation, for example in a service area or off site. This eliminates the inconvenience of having calibration gases in the fab or monitoring location. GD-K71D easily connects to an existing PLC system and is ideal for applications needing a local readout or where a relay control is needed. The automatic zero correction software provides excellent long term stability and minimizes false alarms due to zero drift.

Features:

• LED digital display
• Sensor information and calibration is stored within sensor memory
• Several data transmission options available
• Zero suppression and correction
• Housing design for narrow wall mounting locations
• Self-diagnostic functions by microprocessor
• Electrochemical sensors for most semiconductor gases
• Built-in sampling pump
• Easy replacement of pump and sensor
• Two alarm levels with relays, plus trouble alarm
• 24VDC operation
• Optional NEMA 4X housing available

Applications:

• Semiconductor
• Chemical Processing
• Laboratory
• Manufacturing
• HVAC

*Please note we can only ship RKI products to customers within the United States

C-5501 Hydrogen Peroxide Comparator (round) by AquaPhoenix

C-5501 Hydrogen Peroxide Comparator is a component of K-5510 Hydrogen Peroxide Visual Test Kit and is designed to be compared against the color formed in R-5510 Hydrogen Peroxide CHEMets Refill. The comparator's range is applicable for many dairy and disinfection applications. Color standards are orange in color and cover a range of 0-0.8 ppm hydrogen peroxide.

M020-12112-161 QRAE 3 Multigas Monitor by RAE Systems

The QRAE 3 is a full featured compact 4-gas monitor that provides detection and monitoring of Oxygen (O2), Combustibles and toxic gases that include Carbon Monoxide (CO), Hydrogen Sulfide (H2S), Sulfure Dioxide (SO2) and Hydrogen Cyanide (HCN) and others.

QRAE 3 can deliver wireless real-time instrument readings and alarm status 24/7. This provides better incident visibility and can improve response time.

Monitor-only configuration includes

• Monitor as specified
• Sensors as specified
• Sampling option as specified
• Calibration adapter (diffusion model only)
• T Calibration tube (pumped model only)
• Internal filters (mounted - diffusion model only)
• External filters (one mounted plus pack of 3 - pumped model only)
• Travel charger cradle with computer cable
• Lithium-ion battery pack
• Universal wall adapter
• CD ROM with ProRAE Studio II
• CD ROM with product content
• Quick Reference Guide

Key Features

• Available in Diffusion or Pumped version
• IP-65/67 water and dust resistant case
• Strong, protective, concussion-proof design
• Real-time gas concentration readings and alarm status enabled by state-of-the-art wireless technology
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Large graphical display icon-driven user interface through intuitive, simple-to-operate two-button user interface
• Multi-language support: 18 languages encoded
• Easy access to pump, sensors, filter and battery compartment

Applications

• Industrial safety
• Oil and gas
• Fireground "Toxic Twins" detection
• Environmental
• Fire and Emergency response
• Chemical
• Pharmaceutical
• Telecommunications

*Please note we can only ship RKI products to customers within the United States

Part Number: 44L-252-10