$25 - $50

Part Number: GATC1

TDS1500 Conductivity Solution, 1500ppm/2060uS, 1Qt (946ml) by Sensorex

TDS/Conductivity instruments and sensors must be calibrated together. For a single-point calibration, select the one solution that approximates the expected conductivity or ppm level of total salts. Mixed Salt standards are the most frequently used in the field to sample naturally occurring water sources, boiler feed water, or cooling tower water. Typical river water, well water, or lake water sample will contain a mixture of several different salts. Sensorex Mixed Salt standards simulate a "Natural" mixture of common salt compounds found in these sources. Sodium sulfate, sodium bicarbonate, and sodium chloride salts are blended to provide a representative value. There are certain applications where Single Salt Solutions are preferred. NaCl Solution is routinely used to calibrate instruments measuring Sea Water or brackish water samples. Reagent grade salt and high resistivity DI water is compounded for accurate results. KCI Single Salt Solution may be used with conductivity meters that read directly in Siemens or Ohms. KCI (potassium chloride) is established as an international calibration standard for conductivity measurement. Choose the conductivity calibration solution that is right for your application. CA Residents: Prop 65 WARNING(S)

Part Number: 17L-150A-10

GHS1008 SDS Binders with A-Z Dividers by GHS Safety

Organize and access your Safety Data Sheets quickly and easily with Safety Data Sheet Binders. All binders are manufactured with a thick stiff and rigid vinyl protected cover. This makes binder easy to use, durable, and prevents it from collapsing and crushing its contents over extended usage. Each binder also comes with sturdy A-Z alphabetical reinforced dividers to sort and organize your Safety Data Sheets.

The regular size binders come with a standard 1-1/2" D-slant format ring, holding 300 pages. Printed with bright graphics, these binders will be highly visible in your workplace.

Also available in English/Spanish and English/French

10-108-09 Hydrogen Chloride Colorimetric Gas Detection Tube, 1 - 20 ppmv (10 Tubes / Box) by RAE Systems

RAE Systems colorimetric gas detection tubes enable quick, on-the-spot measurement of a wide range of toxic and combustible gases and vapors. RAE Systems tubes are easy to read, and provide a sharp, clear color change directly corresponding to the concentration of gas present. RAE Systems tubes are compatible with the RAE Systems piston hand pump, a reliable way to draw samples of an exact volume required for the most accurate measurements.

Key Features

• Wide assortment of tubes available to detect over 300 gases and vapors
• Easyto use, even in multiple layers of gloves
• Easy-to-read with sharp,clearcolorchange
• No calibration or other maintenance required

Applications

• Oil and gas
• Chemicals and petrochemicals
• Agriculture and pestcontro
• Food and beverage production
• Environmental protection
• Fire service
• HazMat response
• Nationalsecurity

Part Number: 17L-289-300

*Please note we can only ship RKI products to customers within the United States

TT42V Class 4.2 TDG Label (Vinyl) by GHS Safety

Shipping Labels are essential for packages that contain dangerous goods. GHS labels are available in two materials. Paper for indoor applications and in vinyl for extended outdoor usage using a fade resistant ink. These labels meet the UN Recommendations on the Transport of Dangerous Goods.

Available in 500/roll formats.

100 EZ One Button Operation DMM by Test Products International

The new TPI 100 automatically switches between AC and DC Voltage as well as resistance measurements. No more guessing what range to switch your meter to. The TPI 100 does it automatically.

Features:

• Automatically switches between ACV, DCV, and ohms (resistance). Benefit: Simple to use. Meter selects function and range, just connect the leads to the device under test.
• Single button operation. Benefit: Easy to use. Enables users with limited knowledge to perform tests safely.
• 0 to 600 volts AC and DC Benefit: Enough range to safely perform measurements
• 10 MΩ internal impedance. Benefit: High impedance prevents inaccurate reading caused by circuit loading.
• Auto power off. Benefit: Increases battery life by turning off the multimeter when not in use.
• 4,000 count display
• Up to 40MΩ
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V
• Includes Test Lead Set, Batteries and Protective Rubber Boot
• 3 Year Limited Warranty

Applications:

• Measure line and control circuit voltages
• Measure resistance of motor windings, transformers, and solenoids
• Make general AC and DC voltage and resistance measurements
• Measure the resistance of elements and electric heater cores
• Test continuity of wiring
• Verify voltage at breakers and outlets
• Use as a back-up meter in your tool box

The 100 comes complete with the following accessories:

• 100 Instrument
• Rubber Boot
• Test Lead Set
• 1.5V Battery
• Instruction Manual

SCT-108.001.23 SCT-THYG-PEN-3 Jumbo Dual Display Thermo Hygrometer by ScichemTech

Features:

• Reliable SCT Pocket Type Meter for Humidity & Temperature measurements.
• Comfort / Warm / Cool index with Dual Display.
• Option to select °F/°C.
• Maximum/ minimum (°F /°C) temperature & humidity memory recalling
• 3 m sensor wire with probe for outdoor measurement
• Indoor / Outdoor Temperature & Humidity Display.
• Battery operated.
• With Flipout Stand

TT53V Class 5.2 Intl. TDG Label (Vinyl) by GHS Safety

Shipping Labels are essential for packages that contain dangerous goods. GHS labels are available in two materials. Paper for indoor applications and in vinyl for extended outdoor usage using a fade resistant ink. These labels meet the UN Recommendations on the Transport of Dangerous Goods.

Available in 500/roll formats.

TDS15 Conductivity Solution, 15ppm/23.8uS, 1Qt by Sensorex

TDS/Conductivity instruments and sensors must be calibrated together. For a single-point calibration, select the one solution that approximates the expected conductivity or ppm level of total salts. Mixed Salt standards are the most frequently used in the field to sample naturally occurring water sources, boiler feed water, or cooling tower water. Typical river water, well water, or lake water sample will contain a mixture of several different salts. Sensorex Mixed Salt standards simulate a "Natural" mixture of common salt compounds found in these sources. Sodium sulfate, sodium bicarbonate, and sodium chloride salts are blended to provide a representative value. There are certain applications where Single Salt Solutions are preferred. NaCl Solution is routinely used to calibrate instruments measuring Sea Water or brackish water samples. Reagent grade salt and high resistivity DI water is compounded for accurate results. KCI Single Salt Solution may be used with conductivity meters that read directly in Siemens or Ohms. KCI (potassium chloride) is established as an international calibration standard for conductivity measurement. Choose the conductivity calibration solution that is right for your application. CA Residents: Prop 65 WARNING(S)