$25 - $50

*Please note we can only ship RKI products to customers within the United States

18526-95 Miniature Type-K Thermocouple Female Connector, 2 Pin by Digi-Sense

• Glass-filled nylon construction with hollow pins and molded barriers prevent short circuit
• Secure thermocouple wire into positive/negative terminals with screws
• Each connector comes in ANSI color coded material: type J-black, type K-yellow, and type T-blue
• Miniature connectors are suited for small wires and mineral insulated cables

*Please note we can only ship RKI products to customers within the United States

SCT-108.001.01 SCT-PH PEN-1 Handheld pH Meter by ScichemTech

Includes:

• Handheld pH Meter
• Standard Solution
• Battery
• Screw-Driver
• Instruction Manual

Features:

• Reliable SCT Tester for basic & easy pH measurement.
• Ergonomic Design - Waterproof IP57 rated.
• Accurate & Fast in measurements 0.1 pH resolution.
• Removable & changeable electrode.
• Large and clear display
• Manual calibration through screw trim port 1 or 2 points.
• Battery operated.

TDS18 Conductivity Solution,11.4ppm/18uS, 1Qt by Sensorex

TDS/Conductivity instruments and sensors must be calibrated together. For a single-point calibration, select the one solution that approximates the expected conductivity or ppm level of total salts. Mixed Salt standards are the most frequently used in the field to sample naturally occurring water sources, boiler feed water, or cooling tower water. Typical river water, well water, or lake water sample will contain a mixture of several different salts. Sensorex Mixed Salt standards simulate a "Natural" mixture of common salt compounds found in these sources. Sodium sulfate, sodium bicarbonate, and sodium chloride salts are blended to provide a representative value. There are certain applications where Single Salt Solutions are preferred. NaCl Solution is routinely used to calibrate instruments measuring Sea Water or brackish water samples. Reagent grade salt and high resistivity DI water is compounded for accurate results. KCI Single Salt Solution may be used with conductivity meters that read directly in Siemens or Ohms. KCI (potassium chloride) is established as an international calibration standard for conductivity measurement. Choose the conductivity calibration solution that is right for your application. CA Residents: Prop 65 WARNING(S)

SP60B Switchable Passive Oscilloscope Probe, 60MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

6230NKD Accessories Kit for 6230N Meter by Jenco

Includes:

• 6230F Case
• 6230D115 AC Adapter
• Buffers & Bottles

90205-04 Traceable® T-Bar Waterproof Food Thermometer with Calibration; ±1°C accuracy (-20 to 100°C) by Digi-Sense

Traceable® products are calibrated to NIST-traceable standards and ready to use as soon as you receive it. Each product goes through an intense vetting process before it can carry the Traceable name, and it includes NIST-traceable certification. This means that a 17025-accredited calibration test lab has confirmed that the product meets or exceeds all stated specifications, saving you both time and money by not having to calibrate separately.

NIST-traceable calibration also helps you meet quality standards and regulatory compliance for ISO, FDA, cGMP, VFC, CAP, CLIA and Joint Commission requirements.

• Get accurate, reliable measurements with included NIST-traceable calibration
• Waterproof (IP67 rating)-ideal for food and beverage applications and in washdown areas
• Rugged, shockproof and drop tested to withstand a fall of 5 feet (1.5 meters)
• °F/°C switchable

Includes

Battery and NIST-traceable calibration certificate with data.

18526-99 Miniature Type-T Thermocouple Female Connector, 2 Pin by Digi-Sense

• Glass-filled nylon construction with hollow pins and molded barriers prevent short circuit
• Secure thermocouple wire into positive/negative terminals with screws
• Each connector comes in ANSI color coded material: type J-black, type K-yellow, and type T-blue
• Miniature connectors are suited for small wires and mineral insulated cables

Part Number: 17L-79-1000