$25 - $50

Part Number: 17L-80-500

122 Compact DMM with Adapter Range for Optional Accessories, 0.5% DCV Basic Accuracy by Test Products International

When using the Model 122, press the DATA-H button at any time on any function or range to freeze the reading on the LCD display. This function is very useful when measuring in locations where the display is difficult to read.

Features:

• Safety: Meets CE and IEC 1010 requirements. UL Listed.
• Large LCD: Easy to read at all angles and the majority of lighting levels.
• Data Hold: Freeze readings on the display.
• Rubber Boot: Added protection when the instrument is dropped. (120NB does not include boot.)
• Versatile: Use accessories like a carbon monoxide attachment to expand the capabilities of the 122.
• 2,000 mvDC (2 DCV) adapter range
• 2,000 count display
• 0 to 600 volts AC and DC
• 0 to 2,000 ohms
• Audible continuity
• 10 MOHM internal impedance
• 0.5 % DCV basic accuracy
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

HVAC/R Applications:

• Line voltage
• Control circuit voltage
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring

Electrical Applications:

• Measure line voltage
• Continuity of circuit breakers
• Voltage of direct drive DC motors.

The 120 comes complete with the following accessories:

• 122 Instrument
• Rubber Boot
• Test Lead Set
• 9V Battery
• Instruction Manual

Part Number: 17L-35-1

*Please note we can only ship RKI products to customers within the United States

Part Number: MC2BC1B

WD-00654-01 pH 1.68 Calibration Buffer Solution 500 mL (1-pint) Bottle by Oakton

Choose from economical solution bottles or individually sealed pH buffer pouches.

All Oakton pH buffer solutions are freshness dated, and standardized against NIST-traceable references to ensure quality. ±0.01 pH at 25°C.

OAKTON pH buffer solution bottles are labeled with the name and CAS number for all ingredients (for Right-to-Know requirements), and are supplied with an MSDS (Material Safety Data Sheet).

OAKTON pouches are convenient, air-tight pouches with high-precision calibration standards. Ideal for field use-take them to your test site for on-the-spot calibration. Each box contains twenty 20 mL pouches. Dimensions: 4.5"L x 5"W x 4.5"H (box). Shpg wt 1 lb per box.

• NIST traceable materials
• Labeled with pH vs temperature tables for accurate calibration

Part Number: 17L-50-100

Part Number: CGBUMPB

Part Number: GASFIL

WD-00653-18 1413 µS Conductivity/TDS Calibration Solution 500 mL (1-pint) Bottle by Oakton

Choose from economical 1-pint solution bottles or individually sealed Singles calibration pouches.

All OAKTON Conductivity/TDS calibration solutions are cross checked using different test methods, premixed, and ready to use.

OAKTON conductivity/TDS solution bottles are labeled with the name and CAS number for all ingredients to conform with Right-to-Know requirements, and includes an MSDS. Solutions come in one pint bottles. Dimensions: 7.75"H x 2.25" dia. Shpg wt: 1.1 lbs.

OAKTON Conductivity Singles pouches are convenient, air-tight pouches with high-precision calibration standards. Ideal for field use-take them to your test site for on-the-spot calibration. Pouches are labeled with equivalent values for ppm in KCl, NaCl and 442 and Conductivity values at 25°C and CAS numbers for Right-to-Know requirements. Each box contains twenty 20 mL pouches. Dimensions: 4.5"L x 5"W x 4.5"H (box). Shpg wt 1 lb per box.

• NIST traceable materials
• ±1% accuracy at 25°C

Part Number: 17L-79-1000A

*Please note we can only ship RKI products to customers within the United States

Part Number: 17L-262-15

*Please note we can only ship RKI products to customers within the United States

SP200B Switchable Passive Oscilloscope Probe, 200MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

*Please note we can only ship RKI products to customers within the United States

WD-00653-50 15,000 µS Conductivity/TDS Calibration Solution 500 mL (1-pint) Bottle by Oakton

Choose from economical 1-pint solution bottles or individually sealed Singles calibration pouches.

All OAKTON Conductivity/TDS calibration solutions are cross checked using different test methods, premixed, and ready to use.

OAKTON conductivity/TDS solution bottles are labeled with the name and CAS number for all ingredients to conform with Right-to-Know requirements, and includes an MSDS. Solutions come in one pint bottles. Dimensions: 7.75"H x 2.25" dia. Shpg wt: 1.1 lbs.

OAKTON Conductivity Singles pouches are convenient, air-tight pouches with high-precision calibration standards. Ideal for field use-take them to your test site for on-the-spot calibration. Pouches are labeled with equivalent values for ppm in KCl, NaCl and 442 and Conductivity values at 25°C and CAS numbers for Right-to-Know requirements. Each box contains twenty 20 mL pouches. Dimensions: 4.5"L x 5"W x 4.5"H (box). Shpg wt 1 lb per box.

• NIST traceable materials
• ±1% accuracy at 25°C

GHS1016 Training Certificate (50/pkg) by GHS Safety

HazCom GHS Certificate of Completion is a great way to recognize employee achievement in completing their training on the new HazCom GHS requirements.

This full color certificate is printed on thick sturdy card stock and has a blank areas to put both the student and trainer names. Certificate is 8-1/2" x 11" in size and suitable for framing. Cards are sold 50/pkg.