$25 - $50

*Please note we can only ship RKI products to customers within the United States

P100B Non-Switchable Passive Oscilloscope Probe, 100MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

BW Technologies Auxiliary Filter Replacement for Adaptor (kit of 10)

To preserve and protect the integrity of their gas detection systems, BW Technologies creates a variety of replacement parts. Each of their offerings is cost effective and easy to install. When regularly inspecting the filters, screens, and adaptors, it is useful to have a spare set of compatible filters and screens. Having a clean filter is essential for last minute inspections. When a user notices that a filter is no longer adequate for accurate operation, the replacement filters can easily be changed. The BW Technologies Auxiliary Filter Replacement for Adaptor is available in a kit of 10 filers.

Part Number: MCSSAFK1

10-109-20 Nitrogen Oxides Colorimetric Gas Detection Tube, 1 - 50 ppmv (5 Colorimetric Tubes and 5 Pre-Tubes) by RAE Systems

RAE Systems colorimetric gas detection tubes enable quick, on-the-spot measurement of a wide range of toxic and combustible gases and vapors. RAE Systems tubes are easy to read, and provide a sharp, clear color change directly corresponding to the concentration of gas present. RAE Systems tubes are compatible with the RAE Systems piston hand pump, a reliable way to draw samples of an exact volume required for the most accurate measurements.

Key Features

• Wide assortment of tubes available to detect over 300 gases and vapors
• Easyto use, even in multiple layers of gloves
• Easy-to-read with sharp,clearcolorchange
• No calibration or other maintenance required

Applications

• Oil and gas
• Chemicals and petrochemicals
• Agriculture and pestcontro
• Food and beverage production
• Environmental protection
• Fire service
• HazMat response
• Nationalsecurity

720F Pocket Thermometer with Four Interchangeable Stainless Steel Probes by Jenco

Pocket Thermometer with four interchangeable stainless steel probes for immersion, penetration, surface or air/gases measurements. Sold in kits with all four probes and a handy padded vinyl pouch. Optional 2 meter extended curly cord model 720-31 is available for use when probes and meter are used for remote sensing.

• °C and °F models
• Splash resistant case
• Battery life : ~150 hrs.

480010 Test Strips: Chlorine, 0-10 ppm by AquaPhoenix

Portable and easy to use in detecting various metals, pH, and more. 50 strips per bottle.

PHB-3 Economic Waterproof pH Pocket Tester by Apera

The Apera Instruments PHB-3 Pocket pH Tester is the most economic choice of a reliable pocket pH tester for your regular aqueous solution's pH measurement, including hydroponics, aquaculture, pools & spas, education, tap/drinking water, etc. Easy single button operation for 1-point Auto Calibration (pH 7.0) and 0 to 50°C Auto Temperature Compensation (ATC); ±0.1 pH, 0.5°C accuracy with 0 to 14.0 pH range.

Comes with a complete kit of premixed calibration solution (pH 7.00), AAA batteries in a portable carrying case. Auto power-off in 10 min if no operation, low-battery alarm. IP57 waterproof and dustproof, floating on water so you don't have to worry if it falls into water by accident. 1000 hours' continuous operation (without backlit) powered by AAA batteries.

The meter is CE certified and comes with a 2-year warranty.

• SINGLE-Button operation with Easy Auto Calibration
• Auto Temperature Compensation (ATC) ensures accuracy in variant temperatures (0-50.0°C)
• Complete kit with READY-TO-USE calibration solution and AAA batteries in a portable carrying case
• Auto power-off in 10 min if no operation, low-battery alarm
• 1000 hours of continuous operation powered by 2 AAA batteries

Part Number: PROBEFIL1

TT22P Class 2.2 TDG Label (Paper) by GHS Safety

Shipping Labels are essential for packages that contain dangerous goods. GHS labels are available in two materials. Paper for indoor applications and in vinyl for extended outdoor usage using a fade resistant ink. These labels meet the UN Recommendations on the Transport of Dangerous Goods.

Available in 500/roll formats.

Part Number: 17L-79-1000

SCT-108.001.06 SCT-TDS-PEN-2 Handheld TDS Meter with High Resolution by ScichemTech

Includes:

• Handheld TDS Meter
• Standard Solution
• Battery
• Screw-Driver
• Instruction Manual

Features:

• Reliable SCT Tester for basic & easy TDS measurement.
• Ergonomic Design - Waterproof IP57 rated.
• Accurate & Fast in measurements 1 ppm resolution.
• Removable & changeable electrode.
• Large and clear display
• Manual calibration through screw trim port 1 or 2 points.
• With better TDS resolution 1ppm
• With Automatic Temperature Compensation (ATC).
• Battery operated.

C66 Waterproof Conductivity Tester with Replaceable Electrode (high range) by Milwaukee

The C66 is a conductivity IP65 waterproof tester, specifically designed for the hydroponics and Agricultural markets, with automatic temperature compensation and 1 point manual calibration. The tester has a range of 0.00 to 10.00 mS/cm.

The C66 has a replaceable electrode and is supplied in a casing with calibration solution sachets (M10031) and screwdriver for calibration. The modular design allows easy electrode and battery replacement.