$1000 - $2000

2200-003 GMA 200-MT6/3 GMA 200 Controller, configured for 3 measuring points by GfG

For more than 50 years, the key goal of GfG has been to meet the highest demands of occupational health and safety, industrial equipment reliability and environmental protection. This goal has been reached by developing innovative and reliable gas warning systems. Development of the new GMA 200 gas warning system satisfies these requirements while taking into account suitability testing in line with ATEX Directive 94/9/EC. If switching functions for explosion protection are required, the GMA 200 gas warning system is the optimal solution. It also meets the requirements for gas warning systems without necessary ATEX certification and functional safety requirements (SIL).

Design of the GMA 200 gas warning system

The design of the GMA 200 gas warning system ensures flexible and simple operation in industrial and commercial applications for measuring combustible and toxic gases / vapors, and for measuring oxygen concentrations. The compact design of the GMA 200 as a DIN rail module enables cost-effective and space-saving installation.

Modular design of the GMA 200 MT6 / MT16 gas warning system

Up to 16 detectors can be connected to the GMA 200 gas warning system. A software program enables the quick and easy configuration of the measuring points for already installed GMA 200 gas warning systems. Measuring point designations, the detector type, the type of gas and measuring range as well as three individual or specified alarm thresholds can be programmed for each measuring point using the configuration software. A microprocessor evaluates the analog input signals of the connected detectors.

Integrated relays

As a result of the increasing requirements being placed on safety measures, even redundant protection against gas hazards, complex gas warning systems are in demand. The GMA 200 gas warning system is equipped with 8 internal relays. 6 relays can be freely configured using the software program in order to implement safety measures and alarms. The configuration software offers numerous and flexible options, such as the assignment of one or several measuring points to relays, single alarms per measuring point and alarm threshold, configuration of collective or group alarms and fault messages and voting functions. Two further relays are available for safety-related fault messages and for maintenance.

Relay modules

Using a GMA RT relay module, it is possible to extend the GMA 200 gas warning system by 16 additional freely configurable relays. A total of 4 additional relay modules and thus 64 additional relays can be managed via the GMA 200 gas warning system. Digital connection of the GMA RT relay module to the GMA 200 gas warning system enables the local positioning of the relay modules. The local and thus flexible installation of the relay modules results in large cost savings due to reduced cabling and assembly functions.

Availability of the gas warning system

Besides the traditional voltage supply, the GMA 200 gas warning system can also be operated with a redundant, safety-related voltage supply and therefore meets the highest demands of functional safety and the required permanent availability of gas warning systems for detecting potential gas hazards.

System functions: LED displays

The status of the GMA 200 gas warning system operation, fault, service is shown via LEDs.

Graphical display

The clearly structured layout of the GMA 200 gas warning system enables the quick detection of hazardous situations. Currently measured values are permanently displayed on the LCD graphical display. In the event of gas alarms, the display lighting is automatically activated with a red background.

Additionally, the LED display for Alarm 1, Alarm 2, Alarm 3 is shown. In the event of an alarm, the status of the active relays 1-8 is displayed simultaneously via LEDs.

The integrated memory enables the reading of alarm levels and minimum / maximum values per measuring point at the LCD for an initial, quick hazard assessment.

Data logger function

The GMA 200 gas warning system can be equipped with a micro SD card for saving the measured values. The measured values, mean values, alarm events and faults are permanently stored at individually configurable intervals, and can be read out for evaluation.

Operation via keyboard

Five buttons enable operation at the GMA 200 gas warning system. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the gas warning system, detector and the relays can be retrieved in the operating menu.

Configuration

A USB port at the GMA 200 gas warning system can be used for connection to the configuration software.

Features

• A variety of transmitters can be connected for measurement of combustible, toxic gases/vapors and oxygen
• Multiple relay configurations
• Flexible, reliable and economic
• Intuitive, backlit graphical LCD with "traffic light function" (green, amber, red)
• SIL certification
• DIN rail mounting

35-3000RK-IR-13 IR Carbon Dioxide, 0 - 5% Vol, Sample Draw Assembly in NEMA 4X Enclosure by RKI Instruments

The 35-3000RK series is a compact sample draw detector assembly with a built-in pump that accepts a 24VDC input. This unit features a NEMA 4X enclosure making it dust, water and corrosion resistant. It also features a flowmeter with adjustable flow and a low flow alarm which warns of any obstructions or restrictions in the flow system. Combustibles, oxygen, hydrogen sulfide and carbon monoxide versions are available with or without a 4-20 mA transmitter. The 35-3000RK is also available with both LEL and oxygen sensors in one unit.

The 35-3000RK is capable of single person calibrations and remote sampling at up to 5,000 ft. from a controller, and interfacing to any RKI or third party control system (utilizing a 4-20 mA feedback signal). Multigas versions of this efficient sample draw system are available with up to four sensors, LEL, O2, H2S and CO all in one enclosure. This is a very cost effective way of monitoring for several gases that may be in the same place.

Features

• NEMA 4X enclosure
• Long life pump
• Flowmeter and LED's for operational status
• Low flow indication
• Operates on 24VDC input
• Multigas versions available with up to 4 sensor in one enclosure
• Available in LEL, O2, H2S, CO, H2, HC (ppm)
• LEL and O2 available with or without transmittter
• LEL and O2 available together in one standard compact enclosure

Industry Applications

• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone, & electric utilities
• Parking garages
• Manufacturing facilities
• Steel
• Automotive
• HVAC

*Please note we can only ship RKI products to customers within the United States

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

CC22-771 CC 22 Series Fixed Transmitter with Carbon Monoxide (CO) Sensor, 0 - 100% LEL Range, No Display / 4-20 mA by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

IR22-804-D IR 22 Fixed Transmitter with Carbon Dioxide (CO₂) Sensor, 0 - 5% vol. Range, Display / 4-20 mA by GfG

The IR 22 transmitter combines the proven infrared measurement method to detect carbon dioxide or combustible gases (HC) with the innovative technique of the new 22 series transmitters. This new GfG transmit- ter generation has been developed and manufactured according to SIL standards.

The comprehensive user menu and the versatile setting options make this transmitter series quite flexible and adaptable to all individual requirements. Precise measurement results at various environmental conditions, as well as the large dynamic measurement range of a few ppm up to 5 % volume CO₂ or 100% LEL.

Time-proven and innovative

The EC 22 is equipped with high quality GfG sensors. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow up costs are minimized thanks to the long lifespan of the sensors.

Signal processing

The transmitter includes the complete electronic system for the signal processing and fail-safe forwarding of the measurement signal to the controller. The embedded software of the IR 22 linearises the measurement signal and compensates for environmental influences.

Therefore, when temperature variations are caused by the weather or changes of the humidity, the measured values will be accurate.

In addition, the transmitter provides the option to transfer service, maintenance and error messages to a connected GfG gas measurement controller. The IR 22 transmitter sends the signals either through an analog 4-20 mA current interface or a digital (RS485) Modbus interface.

Flexibility for any application

The IR 22 transmitter includes the sensor, status LEDs, either an analog or a digital interface, "Zero button" to adjust the zero point, and a test socket and potentiometer for the sensor calibration.

In addition, the IR 22 can be ordered with backlit graphical display. The display shows the current gas concentration, allows access to service functions, enables operation using a membrane keypad and includes optical and acoustical signal transmitters.

Features

• Long service life of the infrared (NDIR) sensor
• Extremely stable, low maintenance
• Cost effective single-man adjustment
• Output 4-20 mA or RS485 Modbus

0577 0400 400 IAQ Data Logger for Long Time Measurement by Testo

The IAQ data logger is an autonomous measuring unit for long-term measurements with the testo 400. The universal IAQ instrument is used for programming measuring interval and time. During the measurement, the IAQ data logger works independently from the measuring instrument. In the meantime, the testo 400 can be used for measurements elsewhere. Once the IAQ measurement is completed, you can read out, analyze and document all the saved values with the testo 400.

Main applications of the IAQ data logger in combination with the appropriate probes:

• PMV/PPD measurement in accordance with EN ISO 7730 / ASHRAE 55
• Local discomfort level measurement in accordance with EN ISO 7730 / ASHRAE 55, e.g. draught rate and degree of turbulence at up to three positions at the same time
• NET measurement in accordance with DIN 33403

A practical tripod is available as an accessory for mounting logger and probes.

• Stand-alone data logger for long-term measurements up to 2 weeks
• Compatible with probes for measuring comfort level, degree of turbulence, radiant heat, CO₂, CO, illuminance, air flow velocity, humidity and temperature
• Connect up to six fixed cable probes at the same time
• Analysis and archiving of measurement data with testo DataControl PC software
• Practical tripod for mounting data logger and probes as an accessory

65-2396RK-03 S2 Series IR Carbon Dioxide (CO2) 0 - 5% Sensor/Transmitter, Explosion with Proof J-Box, UL Version by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

6702-8030 MGS-401 Entrance Monitor by Bacharach

The MSA Bacharach® MGS-401 Entrance Monitor centralizes the status of up to four (4) MSA Bacharach diff usion Gas Detectors, which in turn provides and audible and visual alarm outside a monitored space. In addition, the MGS-401 displays any gas concentration level in the space for additional information and visual monitoring. System configuration will determine whether the alarms signals are addressed in the monitored space or at a controller or BMS/BAS level. Combining the MGS-401 Entrance Monitor with the MGS-408 Gas Controller and diffusion Gas Detectors provides a complete, single source gas detection system with an easy means of achieving compliance with refrigeration safety standards such as IIAR, ASHRAE 15, CSA B52 and EN376.

FEATURES

• Perimeter strobe for "at-a-glance" system / alarm status
• Seamless integration with all MSA Bacharach diffusion Gas Detectors
• MGS-408 Controller powers up to (8) total of combination of MGS-401(s) and MGS Diffusion Gas Detectors
• Modbus RTU Master / Slave provides seamless integration from connected gas detectors to many third-party BMS / BAS
• Audible and visual alarms enable compliance with IIAR, ASHRAE 15, CSA B52 and EN378 - no additional hardware required

CC22-701-DM CC 22 Series Fixed Transmitter with Methane (CH₄) Sensor, 0 - 100% LEL Range, Display / Modbus by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

EC22-725-D EC 22 Fixed Transmitter, Chlorine (Cl2) MK 390-0, 0 - 50 ppm, Display / 4-20 mA by GfG

The EC 22 Series are innovative and cost-effective transmitters for the detection of toxic gases or oxygen levels, but without the need for explosion protection.

Time-proven and innovative

The EC 22 is equipped with high quality GfG sensors. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the EC 22 by means of a Modbus interface. Due to the different types of signal transmission, a transmitter from the 22 series can be connected to almost any gas detecting system, also as a supplementary or replacement transmitter on existing systems.

Signal processing

The embedded software of the EC 22 linearizes the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. In addition, the transmitter also offers the option of transmitting service, maintenance, and error messages to a connected gas measuring computer.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display and horn

The clear graphic display of the EC 22 is self explanatory and allows you to read the current status and other important information with ease. The display enables you to navigate effortlessly through the unit s concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm the display changes color from green to red. Two LEDs indicate the status.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP-54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

ECFX-1000-LN Manning EC-FX Gas Detector, NH3 0/1000 ppm, LCD, NEMA 1 Enclosure by Honeywell Analytics

If you use ammonia as part of your refrigeration process, you face several challenges in protecting your plant from the danger and expense of ammonia leaks within cold storage, refrigerated process areas and the engine rooms. Introducing a better, tougher, longer-lasting sensor to cover your needs. The EC-FX-NH3 maintains sensitivity and accuracy — even with rapid changes in temperature and humidity.

Now one tough sensor can work in three harsh environments. With the stability you can count and low cost you want, the EC-FX-NH3 is the new gold standard in ammonia detection.

Features & Benefits

• Responds quickly to ammonia concentrations in low parts per million (PPM)
• Rugged construction for long-term reliability
• ATMOSTM Technology for environmental flexibility

Quick Specs

• Stainless steel enclosure with LCD options
• All-new ammonia sensor with a proprietary electrolyte
• 3-year warranty—twice the warranty of most sensors

*Please note we can only ship RKI products to customers within the United States

M-700137 Manning AirScan IRF9 Transmitter, R22-0/1000-COM, R22 0/1,000 ppm, Commercial Enclosure by Honeywell Analytics

The industrial refrigeration industry is changing rapidly. The manufacture of R-22 and other HCFCs are being phased out. Influential organizations such as EPA and CARB (California Air Resources Board) are enforcing lower level monitoring requirements. Manufacturers of cooling systems are introducing new equipment that runs on 407a, 422d, 410a, HFO-1234yf, NH3 and CO2. In step with these changes, EPA fines have escalated for anyone venting ozone-depleting gases. What's your best move? Contact Honeywell Analytics to learn how to detect for these new refrigerants. With Honeywell Analytics, you can green the environment—and green your bottom line.

Honeywell Analytics Infrared monitoring solutions are designed to help your plant operate more efficiently and cost effectively. Unlike sample draw systems which take longer to pinpoint a gas leak, our diffusion sensing technology cuts downtime and the cost of expensive refrigerant replacement. Other technological advantages include flexible standalone or networkable configurations, long operating life expectancy (10+ years); fewer calibration requirements; self-monitoring SensorCheck technology; EPA compliance including newer requirements set by CARB (California Air Resources Board); and accurate, reliable response to the most common refrigerant gases used in industrial or commercial processes.

Refrigerant Specific

• Rapid response to refrigerants including R-404a, R-22, R-507a, R-134a, R-407a, R-410a, R-422d, HFO-1234yf, NH3 and CO2
• Internal monitoring of 4/20 mA loop circuitry continuously
• Compliant with new monitoring standards set by CARB

Diffusion-Design Sensor

• Has no moving parts and doesn't require pumps or filters
• All points of detection can be monitored continuously at an affordable cost

Versatility

• Can be used with any Honeywell Analytics readout
• Standard range of 0-3,000 ppm, can be rescaled for lower trip points
• Provides a linear output of 4/20 mA as a function of refrigerant concentration
• Simple, real-time calibration eliminates maintenance downtime
• Automatically adapts to fluctuating temperatures

Long-Lasting Performance

• Unique internal reference channel compensates for dust particles, source degradation, humidity and temperature fluctuation, food odors, chemical cleaners, etc.

ATMOS™ Technology

• Allows for operation down to -60°F and in condensing humidity environments or during washdown
• Automatically adapts to its environment and provides accurate and reliable performance under the harshest conditions

SensorCheck™ Technology

• Checks operating parameters of sensors and sends a notification output signal if an anomaly is identified
• Tests the sensor every 24 hours for electrical viability
• Indication can be detected by a Manning gas monitor or PLC

Housing

• High-mass metal bench provides structural and thermal stability and greater immunity to vibration
• Superior EMI/RFI shielding

Applications

• Banana and Produce Rooms
• Beverage Plants
• Wineries and Breweries
• Confined Space Entry
• Food Processing
• Gas Bottling Plants
• Ice Rinks
• Product Coolers
• Rack Houses
• Refrigeration Systems
• Supermarkets

Scintillation Probe - 1.0'' x 0.040' 'NaI (Tl) crystal (1.0"diam x 0.04" thick) (25.4 x 1.0mm) by SE International

Typically, crystals are grown to order once we find the right one for your needs. Below are the specifications for the most common detectors that we offer in this variety.

NaI(Tl), or Sodium Iodide, crystal is recommended for nuclide identification in room temperature application. It provides the best energy resolution for gamma rays in this environment and is relatively inexpensive. Sodium Iodide probes are available in a wide variety of sizes.

The CsI (Tl), or Cesium Iodide, crystal used in Radiation Alert® Probes has a higher atomic number, is more rugged, and less hygroscopic than a typical Nal detector. The improved gamma ray absorption allows a thinner crystal to be used, effectively reducing the background count rate.

1 Inches X 1 Inches (Typically 1.0" dia x 1.0" thick (25.4 x 25.4mm)
2 inches X 2 Inches (Typically 2.0" dia x 2.0" thick (50.8 x 50.8mm)
Smaller and larger custom sizes available.
Nal(Tl) Standard. Optional Extra: BGO, Cs(Tl) or (Na), TSO. Contact for more info.

305ASDD12 30" Aluminum Exhaust Fan in Slant Wall Housing, 5-Wing, 1 / 2 Hp, Direct Drive by Schaefer

Schaefer aluminum slant wall exhaust fans are built with heavy-duty, corrosion resistant aluminum for best-in-class durability and longevity. Using only high quality and energy efficient motors, they are designed for exceptional performance and maximum efficiency, and provide low maintenance and operating costs. The aluminum slant wall exhaust fans are the ideal solution for air exchange and cooling needs in greenhouse application that want an extremely durable fan that will last for many years. Ships fully assembled with shutters to be easily installed in field.

Features and Benefits:

• 5-wing aluminum blade with low solidity ratio for maximum efficiency and airflow and quiet operation
• Durable aluminum vertical uprights for reliable housing and motor support
• Aluminum shutter with reduced flapping for greater efficiency
• Totally enclosed, maintenance free and thermally protected motor for long life and ease of use
• Belt drive models come equipped with self-adjusting idler style belt tensioner for easy adjustment
• Pre-lubricated, permanently sealed ball bearings with optional remote bearing lubrication system for easy maintenance
• OSHA inlet and outlet guards available for additional safety
• Available in belt drive or direct drive
• Suitable for buildings with up to 6" wall thickness using standard rough-in dimensions
• Two year warranty
• Made in the USA

365AS34 36" Aluminum Exhaust Fan in Slant Wall Housing, 5-Wing, 3 / 4 Hp, Belt Drive by Schaefer

Schaefer aluminum slant wall exhaust fans are built with heavy-duty, corrosion resistant aluminum for best-in-class durability and longevity. Using only high quality and energy efficient motors, they are designed for exceptional performance and maximum efficiency, and provide low maintenance and operating costs. The aluminum slant wall exhaust fans are the ideal solution for air exchange and cooling needs in greenhouse application that want an extremely durable fan that will last for many years. Ships fully assembled with shutters to be easily installed in field.

Features and Benefits:

• 5-wing aluminum blade with low solidity ratio for maximum efficiency and airflow and quiet operation
• Durable aluminum vertical uprights for reliable housing and motor support
• Aluminum shutter with reduced flapping for greater efficiency
• Totally enclosed, maintenance free and thermally protected motor for long life and ease of use
• Belt drive models come equipped with self-adjusting idler style belt tensioner for easy adjustment
• Pre-lubricated, permanently sealed ball bearings with optional remote bearing lubrication system for easy maintenance
• OSHA inlet and outlet guards available for additional safety
• Available in belt drive or direct drive
• Suitable for buildings with up to 6" wall thickness using standard rough-in dimensions
• Two year warranty
• Made in the USA