$1000 - $2000

R62757 FPS-COM 5000 P Jedi, US-2013 by Draeger

In an emergency, there is no time for misunderstanding. That's why Draeger developed the FPS-COM 5000 communication unit for NFPA-certified SCBAs. Designed to connect seamlessly to the Draeger FPS® 7000 full-face masks, this proven communication unit ensures clear communication through either a tactical voice amplifier or a radio – even in extreme conditions.

Only your voice is heard

The Draeger FPS-COM 5000 allows you to communicate without interference, even in the noisiest environments. Digital noise-reduction technology eliminates breathing sounds, ambient noise, and acoustic feedback for crystal-clear communication. In addition, the earpiece fits closely to the ear using has a flexible gooseneck that easily adapts to different head sizes and shapes.

Dual side speakers for amplified sound toward the listener

Two speakers mounted on the sides of the Draeger FPS-COM 5000 point in the direction the wearer faces for more effective communication. Speakers are flush mounted to reduce snag hazard and improve balance.

Access to different communication radios

You can use the attached jack to connect the FPS-COM 5000 to more than 350 different radio sets via the external Draeger C-C440 push-to-talk button or the Draeger C-C550 remote speaker microphone. Or you can connect the FPS-COM 5000 directly to the radio and use the built-in push-to-talk button. The communication unit also offers Bluetooth connection to selected radios, including Motorola APX™.

High reliability, low costs

Forgot to turn off the FPS-COM 5000 after a shift? No problem. After a pre-alarm, the communication unit shuts off automatically if no breathing sounds are detected after ten minutes. This increases the battery life, lowers maintenance costs, and ensures that equipment is ready for use when it's needed.

Assembly without special tools

With Draeger's new click-lock system, the FPS-COM 5000 can be attached and removed in just a few steps. And because the FPS-COM 5000 is protected against ingress of water or humidity with an IP67 rating, there is no need to remove the unit for cleaning of the mask.

R62759 FPS-COM 5000 P Kenwood, US-2013 by Draeger

In an emergency, there is no time for misunderstanding. That's why Draeger developed the FPS-COM 5000 communication unit for NFPA-certified SCBAs. Designed to connect seamlessly to the Draeger FPS® 7000 full-face masks, this proven communication unit ensures clear communication through either a tactical voice amplifier or a radio – even in extreme conditions.

Only your voice is heard

The Draeger FPS-COM 5000 allows you to communicate without interference, even in the noisiest environments. Digital noise-reduction technology eliminates breathing sounds, ambient noise, and acoustic feedback for crystal-clear communication. In addition, the earpiece fits closely to the ear using has a flexible gooseneck that easily adapts to different head sizes and shapes.

Dual side speakers for amplified sound toward the listener

Two speakers mounted on the sides of the Draeger FPS-COM 5000 point in the direction the wearer faces for more effective communication. Speakers are flush mounted to reduce snag hazard and improve balance.

Access to different communication radios

You can use the attached jack to connect the FPS-COM 5000 to more than 350 different radio sets via the external Draeger C-C440 push-to-talk button or the Draeger C-C550 remote speaker microphone. Or you can connect the FPS-COM 5000 directly to the radio and use the built-in push-to-talk button. The communication unit also offers Bluetooth connection to selected radios, including Motorola APX™.

High reliability, low costs

Forgot to turn off the FPS-COM 5000 after a shift? No problem. After a pre-alarm, the communication unit shuts off automatically if no breathing sounds are detected after ten minutes. This increases the battery life, lowers maintenance costs, and ensures that equipment is ready for use when it's needed.

Assembly without special tools

With Draeger's new click-lock system, the FPS-COM 5000 can be attached and removed in just a few steps. And because the FPS-COM 5000 is protected against ingress of water or humidity with an IP67 rating, there is no need to remove the unit for cleaning of the mask.

R62846 FPS-COM 5000 P BT Harris, US by Draeger

In an emergency, there is no time for misunderstanding. That's why Draeger developed the FPS-COM 5000 communication unit for NFPA-certified SCBAs. Designed to connect seamlessly to the Draeger FPS® 7000 full-face masks, this proven communication unit ensures clear communication through either a tactical voice amplifier or a radio – even in extreme conditions.

Only your voice is heard

The Draeger FPS-COM 5000 allows you to communicate without interference, even in the noisiest environments. Digital noise-reduction technology eliminates breathing sounds, ambient noise, and acoustic feedback for crystal-clear communication. In addition, the earpiece fits closely to the ear using has a flexible gooseneck that easily adapts to different head sizes and shapes.

Dual side speakers for amplified sound toward the listener

Two speakers mounted on the sides of the Draeger FPS-COM 5000 point in the direction the wearer faces for more effective communication. Speakers are flush mounted to reduce snag hazard and improve balance.

Access to different communication radios

You can use the attached jack to connect the FPS-COM 5000 to more than 350 different radio sets via the external Draeger C-C440 push-to-talk button or the Draeger C-C550 remote speaker microphone. Or you can connect the FPS-COM 5000 directly to the radio and use the built-in push-to-talk button. The communication unit also offers Bluetooth connection to selected radios, including Motorola APX™.

High reliability, low costs

Forgot to turn off the FPS-COM 5000 after a shift? No problem. After a pre-alarm, the communication unit shuts off automatically if no breathing sounds are detected after ten minutes. This increases the battery life, lowers maintenance costs, and ensures that equipment is ready for use when it's needed.

Assembly without special tools

With Draeger's new click-lock system, the FPS-COM 5000 can be attached and removed in just a few steps. And because the FPS-COM 5000 is protected against ingress of water or humidity with an IP67 rating, there is no need to remove the unit for cleaning of the mask.

VN00460 X-am 2500 Multi-Gas Detector, LEL,O2,CO, Rechargeable Kit by Draeger

Draeger's X-am® 2500 accurately detects O₂, CO, NO₂, SO₂ and H₂S and is the only 1 4 gas monitor you need in industrial and refinery applications. The X-am® 2500 combines reliable sensor technology with long battery life and intuitive operation in an instrument that defines safety. It is approved for most markets including mining, oil & gas, chemical, fire and hazardous response, government and many other applications.

Matrix display

The X-am 2500 has a large, easy to read, liquid-crystal display. All gas readings are shown simultaneously and resize automatically depending on the number of sensors installed. When a gas alarm occurs, the reading for the sensor in alarm will be highlighted and will alternate with the alarm level indication of A1 or A2.

High capacity battery

The Draeger X-am 2500 can operate for more than 12 hours with either alkaline batteries or with rechargeable NiMH batteries. Depending on the requirements, the batteries can be charged either in the workshop or in a vehicle. Operating time without an Ex sensor installed is typically more than 250 hours.

X-dock compatibility

The X-am 2500 is compatible with Draeger's X-dock testing and calibration station. X-dock is Draeger's new solution for efficient maintenance and comprehensive equipment management. Used for functional testing and complete documentation, X-dock can complete bump tests in 8 to 15 seconds with more than 40% less gas consumption than competitive using several 500 — 550 mL/min of gas flow. The X-am 2500 is also compatible with the Draeger Bump Test Station.

Long-lasting, reliable sensor technology

The innovative, catalytic Ex sensor has a high degree of drift stability with a high resistance to silicone and hydrogen sulfide. The sensor boasts an expected service life of more than five years and is extremely sensitive to flammable gases and vapors. Further, the X-am 2500 is approved for measuring from methane to nonane, according to IEC/EN 60079-29-1.

Zone 0 approved

The Draeger X-am 2500 has Ex approval for zone 0 for user safety in areas subject to explosion hazard. Additionally, it is not sensitive to electromagnetic radiation, e.g. from wireless devices and is water and dust resistant in accordance with protection class IP 67.

Diffusion or pump

An optional external pump with a hose up to 45 m / 147 ft long is available for use in tanks and shafts or when searching for leaks. The switch from diffusion to pump operation can be handled quickly and easily without tools or screws.

Ergonomic and robust

The Draeger X-am 2500 is comfortably worn thanks to its low weight and ergonomic design and gas can enter the unit from above and from the front—even if the instrument is inside a pocket or if the front gas entry is accidentally covered.

The practical two button control panel and easy menu navigation allow for intuitive operation while the integrated protective rubber coating and sensors not sensitive to shock provide additional safety in case of impacts or vibrations.

Peak value functionality

The X-am 2500 can store the highest gas readings for the Ex and toxic gas sensors and the lowest reading for the O₂ sensor. These readings can be easily reset after a gas exposure without having to turn the monitor off and on.

1X-dock bump test stated times are typical results; stated gas consumption is based upon calibration gas flow of 0.3 L /minute using X-dock for bump test.

VN00581 X-am 2500 Multi-Gas Detector with LEL,O2, CO-LC,NO2 Power Pack by Draeger

Draeger's X-am® 2500 accurately detects O₂, CO, NO₂, SO₂ and H₂S and is the only 1 4 gas monitor you need in industrial and refinery applications. The X-am® 2500 combines reliable sensor technology with long battery life and intuitive operation in an instrument that defines safety. It is approved for most markets including mining, oil & gas, chemical, fire and hazardous response, government and many other applications.

Matrix display

The X-am 2500 has a large, easy to read, liquid-crystal display. All gas readings are shown simultaneously and resize automatically depending on the number of sensors installed. When a gas alarm occurs, the reading for the sensor in alarm will be highlighted and will alternate with the alarm level indication of A1 or A2.

High capacity battery

The Draeger X-am 2500 can operate for more than 12 hours with either alkaline batteries or with rechargeable NiMH batteries. Depending on the requirements, the batteries can be charged either in the workshop or in a vehicle. Operating time without an Ex sensor installed is typically more than 250 hours.

X-dock compatibility

The X-am 2500 is compatible with Draeger's X-dock testing and calibration station. X-dock is Draeger's new solution for efficient maintenance and comprehensive equipment management. Used for functional testing and complete documentation, X-dock can complete bump tests in 8 to 15 seconds with more than 40% less gas consumption than competitive using several 500 — 550 mL/min of gas flow. The X-am 2500 is also compatible with the Draeger Bump Test Station.

Long-lasting, reliable sensor technology

The innovative, catalytic Ex sensor has a high degree of drift stability with a high resistance to silicone and hydrogen sulfide. The sensor boasts an expected service life of more than five years and is extremely sensitive to flammable gases and vapors. Further, the X-am 2500 is approved for measuring from methane to nonane, according to IEC/EN 60079-29-1.

Zone 0 approved

The Draeger X-am 2500 has Ex approval for zone 0 for user safety in areas subject to explosion hazard. Additionally, it is not sensitive to electromagnetic radiation, e.g. from wireless devices and is water and dust resistant in accordance with protection class IP 67.

Diffusion or pump

An optional external pump with a hose up to 45 m / 147 ft long is available for use in tanks and shafts or when searching for leaks. The switch from diffusion to pump operation can be handled quickly and easily without tools or screws.

Ergonomic and robust

The Draeger X-am 2500 is comfortably worn thanks to its low weight and ergonomic design and gas can enter the unit from above and from the front—even if the instrument is inside a pocket or if the front gas entry is accidentally covered.

The practical two button control panel and easy menu navigation allow for intuitive operation while the integrated protective rubber coating and sensors not sensitive to shock provide additional safety in case of impacts or vibrations.

Peak value functionality

The X-am 2500 can store the highest gas readings for the Ex and toxic gas sensors and the lowest reading for the O₂ sensor. These readings can be easily reset after a gas exposure without having to turn the monitor off and on.

1X-dock bump test stated times are typical results; stated gas consumption is based upon calibration gas flow of 0.3 L /minute using X-dock for bump test.

VN00746 PAS COLT 5 MIN WITH CEJN by Draeger

Combining versatility, ease-of-use, and the latest in breathing apparatus design, Draeger's PAS® Colt is among the most technologically advanced, short duration, and emergency escape units available.

Ergonomically designed harness

The PAS Colt is a hip-mounted unit with a distinctive, sophisticated harness design which retains its form, making it easy for the wearer to don the apparatus simply and quickly. The procedure for donning the apparatus is evident at first glance, even to the inexperienced user.

Machine washable harness

The PAS Colt is machine washable and easy to maintain.

Modular Drop-down facility

Equipped, as an option, a unique 'drop-down' feature, whereby the cylinder can be un-clipped from the waistbelt, makes the Draeger PAS Colt ideal for use in confined space entry applications.

VN00749 PAS COLT 10 MIN WITH CEJN by Draeger

Combining versatility, ease-of-use, and the latest in breathing apparatus design, Draeger's PAS® Colt is among the most technologically advanced, short duration, and emergency escape units available.

Ergonomically designed harness

The PAS Colt is a hip-mounted unit with a distinctive, sophisticated harness design which retains its form, making it easy for the wearer to don the apparatus simply and quickly. The procedure for donning the apparatus is evident at first glance, even to the inexperienced user.

Machine washable harness

The PAS Colt is machine washable and easy to maintain.

Modular Drop-down facility

Equipped, as an option, a unique 'drop-down' feature, whereby the cylinder can be un-clipped from the waistbelt, makes the Draeger PAS Colt ideal for use in confined space entry applications.

VN00751 PAS COLT 10 MIN WITH HANSENBRASS by Draeger

Combining versatility, ease-of-use, and the latest in breathing apparatus design, Draeger's PAS® Colt is among the most technologically advanced, short duration, and emergency escape units available.

Ergonomically designed harness

The PAS Colt is a hip-mounted unit with a distinctive, sophisticated harness design which retains its form, making it easy for the wearer to don the apparatus simply and quickly. The procedure for donning the apparatus is evident at first glance, even to the inexperienced user.

Machine washable harness

The PAS Colt is machine washable and easy to maintain.

Modular Drop-down facility

Equipped, as an option, a unique 'drop-down' feature, whereby the cylinder can be un-clipped from the waistbelt, makes the Draeger PAS Colt ideal for use in confined space entry applications.

VN00800 X-zone 5800 Area Monitor, CATEX,H2S/CO-LC,O2,NIMH by Draeger

State-of-the-art area monitoring – the Draeger X-zone® 5800 in combination with the Draeger X-am® 5000, 5100, 5600, and 5800 gas detectors can be used for the measurement of up to six gases. The internal pump and continuous power supply in the explosive area of Zone 0 / C1D1 extend the range of applications in mobile gas detection technology.

Area monitor

• ?Combination with Draeger X-am® 5000, 5100, 5600 or 5800 – measurement of up to 6 gases
• Extensive area/fenceline monitoring up to 25 devices
• Option for permanent power supply in explosive areas (zone 1 / C1D1)

Innovative area monitoring

Even from a distance, the illuminated green LED ring indicates the air is free of monitored toxics and combustible gases. Upon detection of gas hazards, the LED color changes from green to red, thus providing a clear visual warning that gas is present. Additionally, a loud and highly audible evacuation alarm is emitted. The Draeger X-zone 5800 gas entry location permits gas to diffuse into the Draeger X-am 5000, 5100, 5600 and 5800 from all sides.

Wireless fenceline

Up to 25 Draeger X-zone 5800s can be automatically interconnected to form a wireless fenceline. The interconnection of the area monitoring devices allows for rapid establishment of safety networks for larger areas.

A Draeger X-zone 5800 area monitor detecting a gas alarm transmits the alarm signal to all interconnected units. A red flashing alarm in the unit detecting the gas contrasts with alternating red and green flashing alarms of the connected units. This provides simple recognition of alarm status and the actual location of the hazard.

With the corresponding configuration, the maximum gas concentration in the monitored area is shown on the display. Combined with the display of the X-zone ID a clear containment of the hazard area is possible.

Continuous operation of the X-zone for up to 120 hours – or even longer

The 24 Ah battery of the Draeger X-zone 5800 provides up to 120 hours of continuous operation – up to a complete working week.

The Power Supply Ex is available for continuous use of the X-zone 5800. It offers a 50 m (164 ft) supply from a safe area to a potentially explosive area and is approved for use with the X-Zone 5800 in zone 0 / C1D1 areas.

For safe transport, the cable of the Power Supply X is rolled up on a cable drum with the integrated power supply.

Pump or diffusion mode – suitable for your respective application

The X-zone 5800 offers two options for sampling gas: remote pump from 30 m (98 ft) for Zone 0 or diffusion. The pump or diffusion cover plate can be changed without tools.

Other benefits

• ?360° gas entry
• Approval for Ex Zone 0 / C1D1 areas
• Individually configurable with the Draeger CC-Vision PC software (e.g. alarm frequency)
• Inductive charging station: easy and convenient non-contact charging (outside the Ex-area)

Interfaces

?The interfaces on the back of the device offer the possibility of switching actuators in case of alarms by means of the configurable relay. The interface can also directly forward device data, such as measured values of sensors and alarms, via Modbus protocol. This allows you to integrate the devices into existing evaluation units.

VN00802 X-zone 5800 Area Monitor, CATEX,H2S/CO-LC,SO2,O2,NIMH by Draeger

State-of-the-art area monitoring – the Draeger X-zone® 5800 in combination with the Draeger X-am® 5000, 5100, 5600, and 5800 gas detectors can be used for the measurement of up to six gases. The internal pump and continuous power supply in the explosive area of Zone 0 / C1D1 extend the range of applications in mobile gas detection technology.

Area monitor

• ?Combination with Draeger X-am® 5000, 5100, 5600 or 5800 – measurement of up to 6 gases
• Extensive area/fenceline monitoring up to 25 devices
• Option for permanent power supply in explosive areas (zone 1 / C1D1)

Innovative area monitoring

Even from a distance, the illuminated green LED ring indicates the air is free of monitored toxics and combustible gases. Upon detection of gas hazards, the LED color changes from green to red, thus providing a clear visual warning that gas is present. Additionally, a loud and highly audible evacuation alarm is emitted. The Draeger X-zone 5800 gas entry location permits gas to diffuse into the Draeger X-am 5000, 5100, 5600 and 5800 from all sides.

Wireless fenceline

Up to 25 Draeger X-zone 5800s can be automatically interconnected to form a wireless fenceline. The interconnection of the area monitoring devices allows for rapid establishment of safety networks for larger areas.

A Draeger X-zone 5800 area monitor detecting a gas alarm transmits the alarm signal to all interconnected units. A red flashing alarm in the unit detecting the gas contrasts with alternating red and green flashing alarms of the connected units. This provides simple recognition of alarm status and the actual location of the hazard.

With the corresponding configuration, the maximum gas concentration in the monitored area is shown on the display. Combined with the display of the X-zone ID a clear containment of the hazard area is possible.

Continuous operation of the X-zone for up to 120 hours – or even longer

The 24 Ah battery of the Draeger X-zone 5800 provides up to 120 hours of continuous operation – up to a complete working week.

The Power Supply Ex is available for continuous use of the X-zone 5800. It offers a 50 m (164 ft) supply from a safe area to a potentially explosive area and is approved for use with the X-Zone 5800 in zone 0 / C1D1 areas.

For safe transport, the cable of the Power Supply X is rolled up on a cable drum with the integrated power supply.

Pump or diffusion mode – suitable for your respective application

The X-zone 5800 offers two options for sampling gas: remote pump from 30 m (98 ft) for Zone 0 or diffusion. The pump or diffusion cover plate can be changed without tools.

Other benefits

• ?360° gas entry
• Approval for Ex Zone 0 / C1D1 areas
• Individually configurable with the Draeger CC-Vision PC software (e.g. alarm frequency)
• Inductive charging station: easy and convenient non-contact charging (outside the Ex-area)

Interfaces

?The interfaces on the back of the device offer the possibility of switching actuators in case of alarms by means of the configurable relay. The interface can also directly forward device data, such as measured values of sensors and alarms, via Modbus protocol. This allows you to integrate the devices into existing evaluation units.

VN00844 X-am 2500 Multi-Gas Detector, LEL/CO/H2S/O2,No H2-comp Rechargeable Kit by Draeger

Draeger's X-am® 2500 accurately detects O₂, CO, NO₂, SO₂ and H₂S and is the only 1 4 gas monitor you need in industrial and refinery applications. The X-am® 2500 combines reliable sensor technology with long battery life and intuitive operation in an instrument that defines safety. It is approved for most markets including mining, oil & gas, chemical, fire and hazardous response, government and many other applications.

Matrix display

The X-am 2500 has a large, easy to read, liquid-crystal display. All gas readings are shown simultaneously and resize automatically depending on the number of sensors installed. When a gas alarm occurs, the reading for the sensor in alarm will be highlighted and will alternate with the alarm level indication of A1 or A2.

High capacity battery

The Draeger X-am 2500 can operate for more than 12 hours with either alkaline batteries or with rechargeable NiMH batteries. Depending on the requirements, the batteries can be charged either in the workshop or in a vehicle. Operating time without an Ex sensor installed is typically more than 250 hours.

X-dock compatibility

The X-am 2500 is compatible with Draeger's X-dock testing and calibration station. X-dock is Draeger's new solution for efficient maintenance and comprehensive equipment management. Used for functional testing and complete documentation, X-dock can complete bump tests in 8 to 15 seconds with more than 40% less gas consumption than competitive using several 500 — 550 mL/min of gas flow. The X-am 2500 is also compatible with the Draeger Bump Test Station.

Long-lasting, reliable sensor technology

The innovative, catalytic Ex sensor has a high degree of drift stability with a high resistance to silicone and hydrogen sulfide. The sensor boasts an expected service life of more than five years and is extremely sensitive to flammable gases and vapors. Further, the X-am 2500 is approved for measuring from methane to nonane, according to IEC/EN 60079-29-1.

Zone 0 approved

The Draeger X-am 2500 has Ex approval for zone 0 for user safety in areas subject to explosion hazard. Additionally, it is not sensitive to electromagnetic radiation, e.g. from wireless devices and is water and dust resistant in accordance with protection class IP 67.

Diffusion or pump

An optional external pump with a hose up to 45 m / 147 ft long is available for use in tanks and shafts or when searching for leaks. The switch from diffusion to pump operation can be handled quickly and easily without tools or screws.

Ergonomic and robust

The Draeger X-am 2500 is comfortably worn thanks to its low weight and ergonomic design and gas can enter the unit from above and from the front—even if the instrument is inside a pocket or if the front gas entry is accidentally covered.

The practical two button control panel and easy menu navigation allow for intuitive operation while the integrated protective rubber coating and sensors not sensitive to shock provide additional safety in case of impacts or vibrations.

Peak value functionality

The X-am 2500 can store the highest gas readings for the Ex and toxic gas sensors and the lowest reading for the O₂ sensor. These readings can be easily reset after a gas exposure without having to turn the monitor off and on.

1X-dock bump test stated times are typical results; stated gas consumption is based upon calibration gas flow of 0.3 L /minute using X-dock for bump test.

VN00848 X-zone 5800 Area Monitor, PH3,NIMH by Draeger

State-of-the-art area monitoring – the Draeger X-zone® 5800 in combination with the Draeger X-am® 5000, 5100, 5600, and 5800 gas detectors can be used for the measurement of up to six gases. The internal pump and continuous power supply in the explosive area of Zone 0 / C1D1 extend the range of applications in mobile gas detection technology.

Area monitor

• ?Combination with Draeger X-am® 5000, 5100, 5600 or 5800 – measurement of up to 6 gases
• Extensive area/fenceline monitoring up to 25 devices
• Option for permanent power supply in explosive areas (zone 1 / C1D1)

Innovative area monitoring

Even from a distance, the illuminated green LED ring indicates the air is free of monitored toxics and combustible gases. Upon detection of gas hazards, the LED color changes from green to red, thus providing a clear visual warning that gas is present. Additionally, a loud and highly audible evacuation alarm is emitted. The Draeger X-zone 5800 gas entry location permits gas to diffuse into the Draeger X-am 5000, 5100, 5600 and 5800 from all sides.

Wireless fenceline

Up to 25 Draeger X-zone 5800s can be automatically interconnected to form a wireless fenceline. The interconnection of the area monitoring devices allows for rapid establishment of safety networks for larger areas.

A Draeger X-zone 5800 area monitor detecting a gas alarm transmits the alarm signal to all interconnected units. A red flashing alarm in the unit detecting the gas contrasts with alternating red and green flashing alarms of the connected units. This provides simple recognition of alarm status and the actual location of the hazard.

With the corresponding configuration, the maximum gas concentration in the monitored area is shown on the display. Combined with the display of the X-zone ID a clear containment of the hazard area is possible.

Continuous operation of the X-zone for up to 120 hours – or even longer

The 24 Ah battery of the Draeger X-zone 5800 provides up to 120 hours of continuous operation – up to a complete working week.

The Power Supply Ex is available for continuous use of the X-zone 5800. It offers a 50 m (164 ft) supply from a safe area to a potentially explosive area and is approved for use with the X-Zone 5800 in zone 0 / C1D1 areas.

For safe transport, the cable of the Power Supply X is rolled up on a cable drum with the integrated power supply.

Pump or diffusion mode – suitable for your respective application

The X-zone 5800 offers two options for sampling gas: remote pump from 30 m (98 ft) for Zone 0 or diffusion. The pump or diffusion cover plate can be changed without tools.

Other benefits

• ?360° gas entry
• Approval for Ex Zone 0 / C1D1 areas
• Individually configurable with the Draeger CC-Vision PC software (e.g. alarm frequency)
• Inductive charging station: easy and convenient non-contact charging (outside the Ex-area)

Interfaces

?The interfaces on the back of the device offer the possibility of switching actuators in case of alarms by means of the configurable relay. The interface can also directly forward device data, such as measured values of sensors and alarms, via Modbus protocol. This allows you to integrate the devices into existing evaluation units.

VN01552 Pac 8500 H2S/CO W/BT by Draeger

The Draeger Pac® 8500 single-gas detection device is a reliable and precise instrument even under the toughest of conditions. The detector can be equipped with a hydrogen-compensated CO sensor or a Draeger dual sensor. The dual sensors provide the option of measuring two gases at once: either H₂S with CO or O₂ with CO.

Strong performance for maximum safety

You can count on the Draeger Pac 8500 to give you reliable, precise readings at any time even under extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

The Pac 8500 also provides a data and event logger for logging concentrations and events along with the date and time. The data can be loaded on a PC via an interface and processed further there.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Two gas detection in a single-gas device

The Draeger Pac 8500 series offers the following sensor combinations: hydrogen sulfide with carbon monoxide or oxygen with carbon monoxide. Dual sensors enable detection of even low concentrations – all in one and the same handy device. Measuring two gases at the same time reduces downtime as well. You can take vol.% measurements of oxygen and ppm measurements of carbon monoxide simultaneously using just one gas detector.

Measurement of carbon monoxide with significantly reduced cross sensitivity

In industries where carbon monoxide needs to be measured with hydrogen as a background gas, the measured value for carbon monoxide may be falsified by cross sensitivity. Thanks to the special hydrogen-compensated CO sensor from Draeger, this cross sensitivity to hydrogen is significantly reduced in the display of carbon monoxide. This new feature can eliminate the need to carry two different detectors.

Robust design – even for the toughest conditions

The Pac 8500 is easily handled in even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified in the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether functionality of the device has been tested and if it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8500 features clearly visible color coding, thereby minimizing the chance of mistakes.

360° alarm with various functions

If the Draeger Pac 8500 measures hazardous gas concentrations, it sets off an audible, visual and perceptible vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if they have been acknowledged.

The Pac 8500 with oxygen sensor has two additional alarm thresholds in addition to the standard alarm threshold settings. This provides an additional level of safety as a pre-alarm, in addition to the main alarm, can be set for both oxygen enriched and oxygen deficient atmospheres.

Economical operating costs

All of the versions of the Draeger Pac 8500 are equipped with extremely durable Draeger Sensors and a powerful battery.

The Pac 8500 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The detector is then ready to use again right away. Thanks to the powerful battery, the Pac does not require charging on a daily basis and is easy to handle.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to the short test duration and the extremely low consumption of test gas. The Pac 8500 is simply placed in the bump test station and automatically selects the correct setting.

VN01554 Pac 8500 CO-H2 CP W/BT by Draeger

The Draeger Pac® 8500 single-gas detection device is a reliable and precise instrument even under the toughest of conditions. The detector can be equipped with a hydrogen-compensated CO sensor or a Draeger dual sensor. The dual sensors provide the option of measuring two gases at once: either H₂S with CO or O₂ with CO.

Strong performance for maximum safety

You can count on the Draeger Pac 8500 to give you reliable, precise readings at any time even under extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

The Pac 8500 also provides a data and event logger for logging concentrations and events along with the date and time. The data can be loaded on a PC via an interface and processed further there.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Two gas detection in a single-gas device

The Draeger Pac 8500 series offers the following sensor combinations: hydrogen sulfide with carbon monoxide or oxygen with carbon monoxide. Dual sensors enable detection of even low concentrations – all in one and the same handy device. Measuring two gases at the same time reduces downtime as well. You can take vol.% measurements of oxygen and ppm measurements of carbon monoxide simultaneously using just one gas detector.

Measurement of carbon monoxide with significantly reduced cross sensitivity

In industries where carbon monoxide needs to be measured with hydrogen as a background gas, the measured value for carbon monoxide may be falsified by cross sensitivity. Thanks to the special hydrogen-compensated CO sensor from Draeger, this cross sensitivity to hydrogen is significantly reduced in the display of carbon monoxide. This new feature can eliminate the need to carry two different detectors.

Robust design – even for the toughest conditions

The Pac 8500 is easily handled in even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified in the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether functionality of the device has been tested and if it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8500 features clearly visible color coding, thereby minimizing the chance of mistakes.

360° alarm with various functions

If the Draeger Pac 8500 measures hazardous gas concentrations, it sets off an audible, visual and perceptible vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if they have been acknowledged.

The Pac 8500 with oxygen sensor has two additional alarm thresholds in addition to the standard alarm threshold settings. This provides an additional level of safety as a pre-alarm, in addition to the main alarm, can be set for both oxygen enriched and oxygen deficient atmospheres.

Economical operating costs

All of the versions of the Draeger Pac 8500 are equipped with extremely durable Draeger Sensors and a powerful battery.

The Pac 8500 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The detector is then ready to use again right away. Thanks to the powerful battery, the Pac does not require charging on a daily basis and is easy to handle.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to the short test duration and the extremely low consumption of test gas. The Pac 8500 is simply placed in the bump test station and automatically selects the correct setting.

VN01557 Pac 8000 - CO2 W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.

VN01558 Pac 8000 - H2 W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.

VN01559 Pac 8000 - HCN W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.

VN01560 Pac 8000 - NH3 W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.

VN01563 Pac 8000 - OV W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.

VN01564 Pac 8000 - OV - A W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.

VN01565 Pac 8000 - OZONE W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.

VN01566 Pac 8000 - PH W/BT by Draeger

With the robust Draeger Pac® 8000, you'll be well equipped for tough conditions: this non-disposable, personal single-gas detection device is a reliable and precise instrument, which detects hazardous concentrations of twenty nine different gases, including special gases like NO₂, O₃ or COCl₂.

Strong performance for maximum safety

You can count on the Draeger Pac 8000 to give you reliable, precise readings at any time even in extreme conditions. Our powerful sensors with a low t-90 response time ensure quick reactions. In addition to the standard alarms, you can define extra alarm thresholds for TLV®* and STEL*.

* TLV® = Threshold Limit Values, STEL = Short Term Exposure Limit

Sensors for special gases

The Draeger Pac 8000 performs especially well when detecting a variety of special gases. The Pac 8000 can be fitted with sensors for carbon dioxide (CO₂), chlorine gas (Cl₂), hydrogen cyanide (HCN), ammonia (NH₃), nitrogen dioxide (NO₂), phosphine (PH₃) and organic vapors (OV or OV-A).

Further demonstrating the capabilites of Draeger gas detectors is that the Draeger Pac 8000 performs especially well when detecting other gases as well. It can detect ozone (O₃) from concentrations as low as 0.02 ppm and phosgene (COCl₂) from 0.01 ppm. The Pac 8000 detects nitrogen dioxide (NO₂) from concentrations as low as 0.04 ppm.

Robust design – even for the toughest conditions

The Pac 8000 can easily handle even extreme conditions. The sensors can tolerate air pressures between 700 and 1,300 mbar. A membrane filter protects the sensor from foreign matter such as dust and liquids. The shock-proof, chemical-resistant housing meets the requirements specified by the IP68 standard rating.

Easy handling thanks to clear user guidance

The D-Light indicates whether the functionality of the device has been tested and that it is ready to use. The housing is also designed with your safety in mind: each sensor variant of the Draeger Pac 8000 features clear, easily visible color coding, thereby minimizing the chance of mistakes.

User-friendly display with all important information

The large display clearly indicates the respective gas concentration. Other important information, such as the unit of concentration and battery capacity, is also displayed. The bright backlighting ensures that all values can be clearly read in the dark.

360® alarm with various functions

If the Draeger Pac 8000 measures hazardous gas concentrations, it sets off an audible, visual and noticeable vibrating alarm. Two bright, flashing LEDs on the top and bottom of the device ensure that the alarm is easily visible from all sides. The acoustic signal reaches a volume of 90 dB. The display can show the peak concentration measured at any given moment. Earlier alarms registered can also be retrieved at a later time, even if acknowledged.

Data logger and event logger for analyses and reports

The Pac 8000 logs concentrations and events along with date and time. The data can be downloaded to a PC via an interface and processed further there.

Economical operational costs

All of the versions of the Draeger Pac 8000 are equipped with extremely durable Draeger sensors and a powerful battery.

The Pac 8000 is protected against water, dust and other foreign bodies by a special membrane filter. When the filter becomes heavily soiled in use, you can quickly and easily replace it yourself. The device is then ready to use again in no time.

Fast function test saves time and money

Function tests and calibrations can be carried out especially efficiently in the Draeger X-dock® calibration station. The automatic bump tests in the X-dock are a cost-efficient and convenient solution thanks to short test duration and the extremely low test gas consumption. The Pac 8000 is simply placed in the bump test station and automatically selects the correct setting.