$1000 - $2000

1888-701 TX400 Test Station for G888 / G999 by GfG

The TS400 and TX400 test stations quickly and automatically perform the required function tests on Microtector II G450 and G460 personal gas detectors. The TX400 can also be used to adjust sensors with test gas. Both test stations are available with an optional charging function for the portable gas detectors. Gas detection devices make a significant contribution to safety, if they are tested every working day.

Before each use of a portable gas detection device, its operational capability must be checked with a function test ("bump test"). We developed the TS400 and TX400 test stations to make this process as simple, quick and cost-effective as possible for our G450 and G460 portable devices, while still complying with the DGUV information 213-056 (T021) and 213-057 (T023). During the functional test, the test station can be operated using the display and buttons of the inserted gas detector.

Function test and adjustment

After a switched-on gas detection device is placed into either of the two test stations, the station will automatically start a function test. Within a maximum of 30 seconds, the alarms and response times are tested, the time and test interval are set, and the data is stored on a microSD card (optional). The device will then give you feedback about the test's success or, if applicable, any errors that occured. The TX400 can also be used for sensor adjustment. Before starting the adjustment, the zero point of the sensors must be set with fresh air. The sensor sensitivity is then readjusted using the appropriate test gas. Depending on the device and the number of sensors, this process will take a maximum of four minutes.

Power supply and charging function (optional)

The test stations are powered by an external 12-volt power supply unit or by a PC (connected via USB). If a gas detection device is placed inside the docking station while switched off, it will automatically start charging. Once it is fully charged, the test station will switch to trickle charge mode to conserve battery power. A 230 volt power supply or car charging adapter is required for the charging function.

Equipment and accessories

A gas extraction fitting (optional) should be used for test gas application with a gas cylinder. Both test stations are equipped with one input and one output each for supplying and withdrawing test gas. The data is documented on a microSD card. A mini-USB port can be used to connect the device to a PC.

Key features at a glance:

• Meets the requirements of DGUV information 213-056 (T021) and 213-057 (T023) as well as DIN EN 60079-29-2
• Suitable for the portable gas detection devices G450 and G460
• Function test, adjustment (TX400 only) and charging function (optional)
• Data storage on microSD card, data transfer to PC
• Optional: carrying case, power supplies (12 / 24 / 230 V), microSD card, data point software, gas sampling fitting
• Mobile use (no PC - 12/24 V power supply)

194300 TB350 IR Turbidimeter Kit by AquaPhoenix

Features:

• Reads up to 4000 NTU without the need for dilutions
• Superior data management - easily save and recall measurement data sets
• Touchscreen interface for ease of operation
• ISO 7027 Compliant

Ideal for field and environmental testing, the TB350 IR portable turbidimeter delivers the most reliable measurements for low range to high range samples without sacrificing accuracy. The Lovibond® TB Series of turbidimeters offers simplistic operation combined with intelligent instrument engineering to provide an unparalleled level of accuracy in turbidity measurement

Featuring the patent-pending Multipath 90° BLAC® sensor technology, the optical system is engineered with dual detectors to deliver a ratio reading which mitigates common measurement stability issues.

The intuitive, touchscreen interface makes it easy to perform procedures and interpret results. With function applications, you can navigate between settings and perform that function efficiently. This user interface helps eliminates common frustrations and prevents errors. The data logging capabilities allow you to record the testing location, operatorís identification, time, and date along with the measurement. Stored data can be transferred to a computer via USB.

194310 TB350 WL Turbidimeter Kit by AquaPhoenix

Features:

• Reads up to 4000 NTU without the need for dilutions
• Superior data management - easily save and recall measurement data sets
• Touchscreen interface for ease of operation
• US EPA Approved

Ideal for field and environmental testing, the TB350 WL portable turbidimeter delivers the most reliable measurements for low range to high range samples without sacrificing accuracy. The Lovibond® TB Series of turbidimeters offers simplistic operation combined with intelligent instrument engineering to provide an unparalleled level of accuracy in turbidity measurement.

Featuring the patent-pending Multipath 90° BLAC® sensor technology, the optical system is engineered with dual detectors to deliver a ratio reading which mitigates common measurement stability issues.

The intuitive, touchscreen interface makes it easy to perform procedures and interpret results. With function applications, you can navigate between settings and perform that function efficiently. This user interface helps eliminates common frustrations and prevents errors. The data logging capabilities allow you to record the testing location, operatorís identification, time, and date along with the measurement. Stored data can be transferred to a computer via USB.

*Please note we can only ship RKI products to customers within the United States

2200-131 GMA22-MW/1 Versatile Controller for 1 measuring point, 4-20mA or RS-485, with internal power supply by GfG

Gases are also used (or may be found) in smaller facilities such as combined heat and power plants or cold stores. A reliable gas detection system therefore makes a significant contribution to the safety of people, your equipment and the environment. We developed the GMA22-M specifically for gas measurement in these applications. Up to four transmitters and relay modules can be connected to the controller. A display indicating the measured values, integrated visual and audible alarms, and four internal relays for additional safety measures complete the GMA22-M's extensive features.

Gases need to be monitored in many processes - regardless of the size of the plant. Even in smaller applications, a gas warning system is indispensable. The GMA22-M is the ideal controller for this purpose, if

• your application uses up to four transmitters
• you need to monitor toxic and combustible gases or oxygen
• a central display of measured values is required outside hazardous areas
• internal or external relays are required for safety measures
• you want acoustic and visual alarms to be initiated if gas dangers are present

Wide range of connection options

Using its RS-485 interface, the GMA22-M can be connected to up to four transmitters. In addition to the measured values, the controller also receives digital information such as status messages and service notifications. Alternatively, transmitters can also be connected through an analog 4-20 mA or 0.2-1 mA input.

If you are using any of GfG's ACDC capable transmitters, the analog lines can also transfer digital information on the analog lines (only via 4-20 mA). Many GfG transmitters can be calibrated remotely either using ACDC or digital integration. This simplifies service work significantly, allowing it to be performed by a single technician.

Exterior features

The GMA's dimensions (97 x 140 x 50 mm) are exceptionally small, allowing it to be mounted to a wall almost anywhere. The housing is protected against the ingress of dust and splash water according to IP64, making it suitable for use in demanding external conditions.

The 2.2-inch display comes with multicolor backlight. It lights up green in normal operation and red in the event of an alarm. Alarm levels are indicated by two red LEDs. The integrated horn also gives it an additional acoustic alarm. Two further LEDs indicate the operating status and special states in green and yellow. The pushbutton interface below the display allows for intuitive operation and alarm acknowledgement.

Internal and external relays

The GMA22-M has four integrated relays for initiating safety measures. Up to four additional GMA200-RT relay modules can be connected via the RS-485 interface. With 16 floating signal change-over contacts each, the number of relays is then increased to up to 64. The GMA200Config software is used to configure the GMA22-M and the relay modules. Alarms, faults and measured values can be recorded on a microSD card using a featured data logger, if required.

The GMA22-M is available in four different versions:

• GMA22-MW (230 V AC): 3x change-over contact, 1x normally open contact, power supply integrated
• GMA22-MW (24 V DC): 4x change-over contact
• GMA22-MS (230 V AC): 4x normally open contact, power supply integrated
• GMA22-MS (24 V DC): 4x normally open contact

Each version is optionally available with a digital or analog input signal.

Key features at a glance:

General information:

• Suitable for any GfG transmitter
• Monitors one to four measuring points

Features

• 4 integrated relays for safety measures
• 4-20 mA (ACDC capable) or RS-485 (Modbus)
• Color-backlit 2.2" display
• Four colored status LEDs
• Visual and audible alarm
• Compact housing for wall mounting (IP64)

Optional

• Data logger (microSD card)
• With or without integrated power supply
• Different relay versions
• Relay module for extension

2200-132 GMA22-MW/2 Versatile Controller, Configured for 2 measuring points, 4-20mA, with internal power supply by GfG

Gases are also used (or may be found) in smaller facilities such as combined heat and power plants or cold stores. A reliable gas detection system therefore makes a significant contribution to the safety of people, your equipment and the environment. We developed the GMA22-M specifically for gas measurement in these applications. Up to four transmitters and relay modules can be connected to the controller. A display indicating the measured values, integrated visual and audible alarms, and four internal relays for additional safety measures complete the GMA22-M's extensive features.

Gases need to be monitored in many processes - regardless of the size of the plant. Even in smaller applications, a gas warning system is indispensable. The GMA22-M is the ideal controller for this purpose, if

• your application uses up to four transmitters
• you need to monitor toxic and combustible gases or oxygen
• a central display of measured values is required outside hazardous areas
• internal or external relays are required for safety measures
• you want acoustic and visual alarms to be initiated if gas dangers are present

Wide range of connection options

Using its RS-485 interface, the GMA22-M can be connected to up to four transmitters. In addition to the measured values, the controller also receives digital information such as status messages and service notifications. Alternatively, transmitters can also be connected through an analog 4-20 mA or 0.2-1 mA input.

If you are using any of GfG's ACDC capable transmitters, the analog lines can also transfer digital information on the analog lines (only via 4-20 mA). Many GfG transmitters can be calibrated remotely either using ACDC or digital integration. This simplifies service work significantly, allowing it to be performed by a single technician.

Exterior features

The GMA's dimensions (97 x 140 x 50 mm) are exceptionally small, allowing it to be mounted to a wall almost anywhere. The housing is protected against the ingress of dust and splash water according to IP64, making it suitable for use in demanding external conditions.

The 2.2-inch display comes with multicolor backlight. It lights up green in normal operation and red in the event of an alarm. Alarm levels are indicated by two red LEDs. The integrated horn also gives it an additional acoustic alarm. Two further LEDs indicate the operating status and special states in green and yellow. The pushbutton interface below the display allows for intuitive operation and alarm acknowledgement.

Internal and external relays

The GMA22-M has four integrated relays for initiating safety measures. Up to four additional GMA200-RT relay modules can be connected via the RS-485 interface. With 16 floating signal change-over contacts each, the number of relays is then increased to up to 64. The GMA200Config software is used to configure the GMA22-M and the relay modules. Alarms, faults and measured values can be recorded on a microSD card using a featured data logger, if required.

The GMA22-M is available in four different versions:

• GMA22-MW (230 V AC): 3x change-over contact, 1x normally open contact, power supply integrated
• GMA22-MW (24 V DC): 4x change-over contact
• GMA22-MS (230 V AC): 4x normally open contact, power supply integrated
• GMA22-MS (24 V DC): 4x normally open contact

Each version is optionally available with a digital or analog input signal.

Key features at a glance:

General information:

• Suitable for any GfG transmitter
• Monitors one to four measuring points

Features

• 4 integrated relays for safety measures
• 4-20 mA (ACDC capable) or RS-485 (Modbus)
• Color-backlit 2.2" display
• Four colored status LEDs
• Visual and audible alarm
• Compact housing for wall mounting (IP64)

Optional

• Data logger (microSD card)
• With or without integrated power supply
• Different relay versions
• Relay module for extension

2200-133 GMA22-MW/3 Versatile Controller, Configured for 3 measuring points, 4-20mA, with internal power supply by GfG

Gases are also used (or may be found) in smaller facilities such as combined heat and power plants or cold stores. A reliable gas detection system therefore makes a significant contribution to the safety of people, your equipment and the environment. We developed the GMA22-M specifically for gas measurement in these applications. Up to four transmitters and relay modules can be connected to the controller. A display indicating the measured values, integrated visual and audible alarms, and four internal relays for additional safety measures complete the GMA22-M's extensive features.

Gases need to be monitored in many processes - regardless of the size of the plant. Even in smaller applications, a gas warning system is indispensable. The GMA22-M is the ideal controller for this purpose, if

• your application uses up to four transmitters
• you need to monitor toxic and combustible gases or oxygen
• a central display of measured values is required outside hazardous areas
• internal or external relays are required for safety measures
• you want acoustic and visual alarms to be initiated if gas dangers are present

Wide range of connection options

Using its RS-485 interface, the GMA22-M can be connected to up to four transmitters. In addition to the measured values, the controller also receives digital information such as status messages and service notifications. Alternatively, transmitters can also be connected through an analog 4-20 mA or 0.2-1 mA input.

If you are using any of GfG's ACDC capable transmitters, the analog lines can also transfer digital information on the analog lines (only via 4-20 mA). Many GfG transmitters can be calibrated remotely either using ACDC or digital integration. This simplifies service work significantly, allowing it to be performed by a single technician.

Exterior features

The GMA's dimensions (97 x 140 x 50 mm) are exceptionally small, allowing it to be mounted to a wall almost anywhere. The housing is protected against the ingress of dust and splash water according to IP64, making it suitable for use in demanding external conditions.

The 2.2-inch display comes with multicolor backlight. It lights up green in normal operation and red in the event of an alarm. Alarm levels are indicated by two red LEDs. The integrated horn also gives it an additional acoustic alarm. Two further LEDs indicate the operating status and special states in green and yellow. The pushbutton interface below the display allows for intuitive operation and alarm acknowledgement.

Internal and external relays

The GMA22-M has four integrated relays for initiating safety measures. Up to four additional GMA200-RT relay modules can be connected via the RS-485 interface. With 16 floating signal change-over contacts each, the number of relays is then increased to up to 64. The GMA200Config software is used to configure the GMA22-M and the relay modules. Alarms, faults and measured values can be recorded on a microSD card using a featured data logger, if required.

The GMA22-M is available in four different versions:

• GMA22-MW (230 V AC): 3x change-over contact, 1x normally open contact, power supply integrated
• GMA22-MW (24 V DC): 4x change-over contact
• GMA22-MS (230 V AC): 4x normally open contact, power supply integrated
• GMA22-MS (24 V DC): 4x normally open contact

Each version is optionally available with a digital or analog input signal.

Key features at a glance:

General information:

• Suitable for any GfG transmitter
• Monitors one to four measuring points

Features

• 4 integrated relays for safety measures
• 4-20 mA (ACDC capable) or RS-485 (Modbus)
• Color-backlit 2.2" display
• Four colored status LEDs
• Visual and audible alarm
• Compact housing for wall mounting (IP64)

Optional

• Data logger (microSD card)
• With or without integrated power supply
• Different relay versions
• Relay module for extension

2200-141 GMA22-MW/1 Versatile Controller, For 1 measuring point. 4-20mA or RS-485, power supply not included by GfG

Gases are also used (or may be found) in smaller facilities such as combined heat and power plants or cold stores. A reliable gas detection system therefore makes a significant contribution to the safety of people, your equipment and the environment. We developed the GMA22-M specifically for gas measurement in these applications. Up to four transmitters and relay modules can be connected to the controller. A display indicating the measured values, integrated visual and audible alarms, and four internal relays for additional safety measures complete the GMA22-M's extensive features.

Gases need to be monitored in many processes - regardless of the size of the plant. Even in smaller applications, a gas warning system is indispensable. The GMA22-M is the ideal controller for this purpose, if

• your application uses up to four transmitters
• you need to monitor toxic and combustible gases or oxygen
• a central display of measured values is required outside hazardous areas
• internal or external relays are required for safety measures
• you want acoustic and visual alarms to be initiated if gas dangers are present

Wide range of connection options

Using its RS-485 interface, the GMA22-M can be connected to up to four transmitters. In addition to the measured values, the controller also receives digital information such as status messages and service notifications. Alternatively, transmitters can also be connected through an analog 4-20 mA or 0.2-1 mA input.

If you are using any of GfG's ACDC capable transmitters, the analog lines can also transfer digital information on the analog lines (only via 4-20 mA). Many GfG transmitters can be calibrated remotely either using ACDC or digital integration. This simplifies service work significantly, allowing it to be performed by a single technician.

Exterior features

The GMA's dimensions (97 x 140 x 50 mm) are exceptionally small, allowing it to be mounted to a wall almost anywhere. The housing is protected against the ingress of dust and splash water according to IP64, making it suitable for use in demanding external conditions.

The 2.2-inch display comes with multicolor backlight. It lights up green in normal operation and red in the event of an alarm. Alarm levels are indicated by two red LEDs. The integrated horn also gives it an additional acoustic alarm. Two further LEDs indicate the operating status and special states in green and yellow. The pushbutton interface below the display allows for intuitive operation and alarm acknowledgement.

Internal and external relays

The GMA22-M has four integrated relays for initiating safety measures. Up to four additional GMA200-RT relay modules can be connected via the RS-485 interface. With 16 floating signal change-over contacts each, the number of relays is then increased to up to 64. The GMA200Config software is used to configure the GMA22-M and the relay modules. Alarms, faults and measured values can be recorded on a microSD card using a featured data logger, if required.

The GMA22-M is available in four different versions:

• GMA22-MW (230 V AC): 3x change-over contact, 1x normally open contact, power supply integrated
• GMA22-MW (24 V DC): 4x change-over contact
• GMA22-MS (230 V AC): 4x normally open contact, power supply integrated
• GMA22-MS (24 V DC): 4x normally open contact

Each version is optionally available with a digital or analog input signal.

Key features at a glance:

General information:

• Suitable for any GfG transmitter
• Monitors one to four measuring points

Features

• 4 integrated relays for safety measures
• 4-20 mA (ACDC capable) or RS-485 (Modbus)
• Color-backlit 2.2" display
• Four colored status LEDs
• Visual and audible alarm
• Compact housing for wall mounting (IP64)

Optional

• Data logger (microSD card)
• With or without integrated power supply
• Different relay versions
• Relay module for extension

2200-142 GMA22-MW/2 Versatile Controller, Configured for 2 measuring points, 4-20mA, power supply not included by GfG

Gases are also used (or may be found) in smaller facilities such as combined heat and power plants or cold stores. A reliable gas detection system therefore makes a significant contribution to the safety of people, your equipment and the environment. We developed the GMA22-M specifically for gas measurement in these applications. Up to four transmitters and relay modules can be connected to the controller. A display indicating the measured values, integrated visual and audible alarms, and four internal relays for additional safety measures complete the GMA22-M's extensive features.

Gases need to be monitored in many processes - regardless of the size of the plant. Even in smaller applications, a gas warning system is indispensable. The GMA22-M is the ideal controller for this purpose, if

• your application uses up to four transmitters
• you need to monitor toxic and combustible gases or oxygen
• a central display of measured values is required outside hazardous areas
• internal or external relays are required for safety measures
• you want acoustic and visual alarms to be initiated if gas dangers are present

Wide range of connection options

Using its RS-485 interface, the GMA22-M can be connected to up to four transmitters. In addition to the measured values, the controller also receives digital information such as status messages and service notifications. Alternatively, transmitters can also be connected through an analog 4-20 mA or 0.2-1 mA input.

If you are using any of GfG's ACDC capable transmitters, the analog lines can also transfer digital information on the analog lines (only via 4-20 mA). Many GfG transmitters can be calibrated remotely either using ACDC or digital integration. This simplifies service work significantly, allowing it to be performed by a single technician.

Exterior features

The GMA's dimensions (97 x 140 x 50 mm) are exceptionally small, allowing it to be mounted to a wall almost anywhere. The housing is protected against the ingress of dust and splash water according to IP64, making it suitable for use in demanding external conditions.

The 2.2-inch display comes with multicolor backlight. It lights up green in normal operation and red in the event of an alarm. Alarm levels are indicated by two red LEDs. The integrated horn also gives it an additional acoustic alarm. Two further LEDs indicate the operating status and special states in green and yellow. The pushbutton interface below the display allows for intuitive operation and alarm acknowledgement.

Internal and external relays

The GMA22-M has four integrated relays for initiating safety measures. Up to four additional GMA200-RT relay modules can be connected via the RS-485 interface. With 16 floating signal change-over contacts each, the number of relays is then increased to up to 64. The GMA200Config software is used to configure the GMA22-M and the relay modules. Alarms, faults and measured values can be recorded on a microSD card using a featured data logger, if required.

The GMA22-M is available in four different versions:

• GMA22-MW (230 V AC): 3x change-over contact, 1x normally open contact, power supply integrated
• GMA22-MW (24 V DC): 4x change-over contact
• GMA22-MS (230 V AC): 4x normally open contact, power supply integrated
• GMA22-MS (24 V DC): 4x normally open contact

Each version is optionally available with a digital or analog input signal.

Key features at a glance:

General information:

• Suitable for any GfG transmitter
• Monitors one to four measuring points

Features

• 4 integrated relays for safety measures
• 4-20 mA (ACDC capable) or RS-485 (Modbus)
• Color-backlit 2.2" display
• Four colored status LEDs
• Visual and audible alarm
• Compact housing for wall mounting (IP64)

Optional

• Data logger (microSD card)
• With or without integrated power supply
• Different relay versions
• Relay module for extension

2200-143 GMA22-MW/3 Versatile Controller, Configured for 3 measuring points, 4-20mA, power supply not included by GfG

Gases are also used (or may be found) in smaller facilities such as combined heat and power plants or cold stores. A reliable gas detection system therefore makes a significant contribution to the safety of people, your equipment and the environment. We developed the GMA22-M specifically for gas measurement in these applications. Up to four transmitters and relay modules can be connected to the controller. A display indicating the measured values, integrated visual and audible alarms, and four internal relays for additional safety measures complete the GMA22-M's extensive features.

Gases need to be monitored in many processes - regardless of the size of the plant. Even in smaller applications, a gas warning system is indispensable. The GMA22-M is the ideal controller for this purpose, if

• your application uses up to four transmitters
• you need to monitor toxic and combustible gases or oxygen
• a central display of measured values is required outside hazardous areas
• internal or external relays are required for safety measures
• you want acoustic and visual alarms to be initiated if gas dangers are present

Wide range of connection options

Using its RS-485 interface, the GMA22-M can be connected to up to four transmitters. In addition to the measured values, the controller also receives digital information such as status messages and service notifications. Alternatively, transmitters can also be connected through an analog 4-20 mA or 0.2-1 mA input.

If you are using any of GfG's ACDC capable transmitters, the analog lines can also transfer digital information on the analog lines (only via 4-20 mA). Many GfG transmitters can be calibrated remotely either using ACDC or digital integration. This simplifies service work significantly, allowing it to be performed by a single technician.

Exterior features

The GMA's dimensions (97 x 140 x 50 mm) are exceptionally small, allowing it to be mounted to a wall almost anywhere. The housing is protected against the ingress of dust and splash water according to IP64, making it suitable for use in demanding external conditions.

The 2.2-inch display comes with multicolor backlight. It lights up green in normal operation and red in the event of an alarm. Alarm levels are indicated by two red LEDs. The integrated horn also gives it an additional acoustic alarm. Two further LEDs indicate the operating status and special states in green and yellow. The pushbutton interface below the display allows for intuitive operation and alarm acknowledgement.

Internal and external relays

The GMA22-M has four integrated relays for initiating safety measures. Up to four additional GMA200-RT relay modules can be connected via the RS-485 interface. With 16 floating signal change-over contacts each, the number of relays is then increased to up to 64. The GMA200Config software is used to configure the GMA22-M and the relay modules. Alarms, faults and measured values can be recorded on a microSD card using a featured data logger, if required.

The GMA22-M is available in four different versions:

• GMA22-MW (230 V AC): 3x change-over contact, 1x normally open contact, power supply integrated
• GMA22-MW (24 V DC): 4x change-over contact
• GMA22-MS (230 V AC): 4x normally open contact, power supply integrated
• GMA22-MS (24 V DC): 4x normally open contact

Each version is optionally available with a digital or analog input signal.

Key features at a glance:

General information:

• Suitable for any GfG transmitter
• Monitors one to four measuring points

Features

• 4 integrated relays for safety measures
• 4-20 mA (ACDC capable) or RS-485 (Modbus)
• Color-backlit 2.2" display
• Four colored status LEDs
• Visual and audible alarm
• Compact housing for wall mounting (IP64)

Optional

• Data logger (microSD card)
• With or without integrated power supply
• Different relay versions
• Relay module for extension