$1000 - $2000

2106B1706 Sensepoint Hazardous Area Approved Gas Detector, CO 0-200 ppm Toxic Sensor 3/4NPT by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

EC22-725-D EC 22 Fixed Transmitter, Chlorine (Cl2) MK 390-0, 0 - 50 ppm, Display / 4-20 mA by GfG

The EC 22 Series are innovative and cost-effective transmitters for the detection of toxic gases or oxygen levels, but without the need for explosion protection.

Time-proven and innovative

The EC 22 is equipped with high quality GfG sensors. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the EC 22 by means of a Modbus interface. Due to the different types of signal transmission, a transmitter from the 22 series can be connected to almost any gas detecting system, also as a supplementary or replacement transmitter on existing systems.

Signal processing

The embedded software of the EC 22 linearizes the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. In addition, the transmitter also offers the option of transmitting service, maintenance, and error messages to a connected gas measuring computer.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display and horn

The clear graphic display of the EC 22 is self explanatory and allows you to read the current status and other important information with ease. The display enables you to navigate effortlessly through the unit s concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm the display changes color from green to red. Two LEDs indicate the status.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP-54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

WD-35643-05 DO 100 Portable DO Meter Kit with DO Probe and Case by Oakton

The new addition to the Environmental Express Oakton product line features updates to measuring water quality easier and faster. The larger display is 2.75 in. by 2.0 in. for better viewing angle, and has indicators for battery life, stability, and calibration. It shows both the parameter and temperature measurements at the same time.

The meter is a perfect combination of the most advanced electronics technology, sensor technology, and software design all while being the most cost-effective portable electrochemical meter. The microprocessor-based meter features automatic calibration, automatic temperature, salinity compensation, function set-up, self-diagnostics, automatic power-off, and low voltage display.

DO 100 portable meter comes with a polarographic electrode and a special DO calibration sleeve, taking only three to five minutes to polarize. The electrode also comes with three combined membrane caps so the membrane can be easily replaced.

• Digital filter improves measurement speed and accuracy
• Clear large-screen LCD with white backlight
• Stable reading and automatic lock-up modes available
• IP57 waterproof and dust-resistant rated – great for use under harsh environments
• Includes polarographic DO electrode with built-in temperature sensor

Includes

Meter includes three AA batteries

DO 100 portable meter, polarographic DO electrode, 30 mL DO inner solution, cathode polishing paper, DO electrode membrane cap, carrying case

20CFO-SWDS-3 20" Washdown Duty Fan, Stainless Steel Motor, Stainless Steel OSHA Guards and Stainless Steel Blade, 3-Phase by Schaefer

Increase productivity and improve work area safety with high performance Schaefer washdown duty air circulators. Designed to withstand frequent washing and for long life in wet and moist environments these fans are ideal for food and beverage processing facilities, kitchens, hospitals and other clean, corrosive or humid environments.

Features and Benefits

• Choice of three sizes: 20", 24" and 30" diameter
• Corrosion resistant electro-polished 304 stainless steel, OSHA compliant guards
• Extremely high airflow compared to competitive offerings
• Pedestals and stainless steel wall mounts available

Blade Choices:

• Stainless Steel: Excellent corrosion resistance. Electro-polished surface for easy cleaning and minimal bacteria growth. Meets USDA, FDA and NSF/ANSI/3-A standards. Rigid enough to be pressure washed while operating.
• Polypropylene: A less expensive option. Excellent corrosion resistance. Excellent tolerance to a broad range of chemicals. Lighter weight. Should not be pressure washed while operating. The only blade choice for anodized aluminum motors.

Motor Choices:

• Stainless Steel: Best for frequent wash downs. IP55 enclosure protection. Meets USDA and NSF/ANSI/3-A standards. 1-phase and 3-phase. 3-phase is VFD compatible. 2-year warranty.
• Epoxy Coated: Very powerful motors. Best for occasional wash downs. USDA and FDA approved corrosion resistant white epoxy finish. IP55 enclosure protection. 1-phase and 3-phase. 1-year warranty.
• Anodized Aluminum: Best for high temperature applications. Only available with a polypropylene blade. IP55 enclosure protection. Class F insulation. Meets UL, CSA and CE standards. 1-phase is speed controllable. 3-phase is VFD compatible. 3-year warranty.

SPLIC1BAXCMAZZ Sensepoint XRL Fixed Point Gas Leak Detector, Bluetooth, ATEX, CO 300ppm, 4-20mA, Charcoal Grey by Honeywell Analytics

Sensepoint XRL is a fixed point gas leak detector that is designed to meet the needs of industrial applications. With over 50 years experience in gas leak detection, Honeywell offers a flexible range of highly-reliable sensing devices to meet those needs.

• Quick installation
• Rapid configuration
• Simple to operate
• Straightforward to maintain

Honeywell innovation enables customers to pair the gas detector with their mobile phone, and then use an app to perform many tasks related to installation, commissioning and maintenance.

Flexible Output Options

Sensepoint XRL is available with either mA loop analog output or Modbus RTU. The result is a flexible solution that can easily be incorporated into legacy systems as well as new installations.

Easy Control and Maintenance

Sensepoint XRL's smartphone interface makes for much faster calibration, configuration and bump tests. Inspecting the status and settings of individual Sensepoint XRL detectors is simple. Use the mobile app to:

• Read gas concentrations in real-time
• Reconfigure settings
• Check unit histories

Automated Reporting

Increase the efficiency of your operations and reduce administration time. The app and Sensepoint XRL provides easy access to diagnostic information and generates calibration reports at the touch of a screen.

Compatible System Controller

Touchpoint Plus is the perfect complement to Sensepoint XRL, providing an intuitive, easy to operate gas detection solution to meet the needs of your business.

Visual Integration

Clean aesthetics and a choice of colors mean that the detector appearance can be selected to compare or contrast with the environment in which it is being used.

Typical Applications

• Manufacturing facilities and factories
• Water treatment plants
• Battery charging facilities
• Vehicle test facilities
• Petrochemical plants
• Fuelling depots

Accessories

• Calibration cap
• Collecting cone
• Pole Mount Bracket Kit
• Duct Mount Kit
• Weather Protection
• Flow Housing

FEATURES & BENEFITS

• Choose from a range of mA or Modbus output versions for flexible system design to meet the customers requirements.
• Selectable source or sink current for analog output enables one detector to be suitable for both system configurations.
• The ingress protection of NEMA 4X/IP66 allows units to be installed in outdoor environemtns.
• Simplified maintenance with familiar smartphone technology saves money and time.
• Multi-color visual indicator to show status makes it easier to know the detector status immediately and identify detectors that require attention or are warning of danger.
• Manage the detector without making a physical connection. Remove the need for physical access to hard-to-reach devices.
• One person calibration without the need to open the detector. Saves time and removes need for hot work permit.

90452-56 Secondary SPRT, 0.25" x 12", -200~670C, Bare Wire by Digi-Sense

AM1762 Series - Secondary standard SPRT/RTD probes: These probes fill the gap between affordable, but temperature limited secondary PRTs and more expensive, yet highly accurate SPRTs. The unique design makes them very stable both short term (±2 mK at TPW) and long term (<19 mK typical at TPW after 500 hours) accuracy is ±6 mK at TPW . These high performance probes fully meet ITS-90 criteria for reference thermometers and are an excellent choices for reference standards for metrology labs of various levels. The Am1762 is nominally 25.5 ohm

• Equivalent to Fluke Calibration / Hart Scientific Model 5628

72-PBA-F GX-3R Pro 5 Gas Personal Monitor - LEL / O2 / H2S / CO (individual CO and H2S sensors) - CO2, 10,000 ppm, IR (ETA Aug 2019) - Li-Ion Battery Pack with 100-240 VAC and 12 VDC Chargers by RKI Instruments

The GX-3R Pro is the world's smallest 5-gas monitor weighing only 4.58 ounces and fits in the palm of your hand (2.9" W x 2.6" H x 1.06" D). It simultaneously monitors and displays 5 different gases. In addition to monitoring standard confined space gases, LEL, O₂, CO, & H₂S, the GX-3R Pro has a 5th channel where you can add infrared or toxic sensors. Two of the four sensor slots have interchangeable sensors providing flexible configurations, which can easily be changed in the field.

The GX-3R Pro comes equipped with Bluetooth wireless communication, man-down alarm, the choice of alkaline or rechargeable power supply, and a 3 year warranty. The Lithium-ion battery pack will operate for 25 hours and will fully charge in 3 hours.

The GX-3R Pro utilizes Bluetooth communication to display direct gas readings from the instrument to a phone app, which is available free on either iOS or Android phones. Automatic notifications can be programmed to send text or email messages, if there is an alarm event from the GX-3R Pro.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 5 gas monitor: 2.9" W x 2.6" H x 1.06" D , 4.58 ounces
• Simultaneous detection of 5 gases: LEL, O₂, H₂S, CO, and other optional sensors; H₂ Compensated CO sensor available
• Simple 2-button operation
• Bluetooth communication with iOS & Android App
• Non-Compliance Indicator
• 3 user adjustable alarm levels
• Panic Alarm - Tap instrument twice
• Man Down Alarm
• Impact resistant body
• Large full dot, auto-backlit display with auto-rotation
• Stealth mode for law enforcement
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

CC22-772-DM CC 22 Series Fixed Transmitter with Methanol (CH₄O) Sensor, 0 - 100% LEL Range, Display / Modbus by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

XT-XUHM-B-EU GasAlertMax XT II 4 Gas Detector, Combustible (% LEL, unfiltered), Oxygen (O2), Hydrogen Sulfide (H2S), Carbon Monoxide (CO) - Black Housing, EU version (Europe) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XT-XUHM-B-EU

GD-70D-HCL-15E GD-70D Smart Transmitter, HCl (hydrogen chloride), 0-15 ppm, with ESU-23E by RKI Instruments

RKI Instruments has been making high quality gas detection and monitoring units for over 15 years. With an emphasis on safety and reliability, RKI Instruments excels at providing the best products in gas detection and sensor technology on the market. Every year, RKI strives to improve its product offering and scours the globe for the latest technologies and innovative designs. With the introduction of the GD-70D Series Intelligent Gas Detector, employers and workplace safety managers can feel confident that they have purchased a reliable detector that is built to last.

GD-70D Series Intelligent Gas Detector

The GD-70D Series Intelligent Gas Detector is a new smart gas detection transmitter that monitors combustibles, oxygen, and a wide range of toxic gases. The unit can be used as a standalone device, integrated with other PLC systems, or integrated with RKI's Beacon series of single and multi-channel controllers. Its common platform integrates numerous detection methods and requires very little maintenance.

Exclusive Features

The plug and play intelligent sensors make for easy setup and calibration by internally retaining calibration and sensor data. This allows workers to replace sensors while in the field without the need to reprogram the equipment. For little maintenance and optimal reliability, the internal technology automatically adjusts for long-term zero and span drift. The pump flow is also self-tuning for low maintenance functioning. In general, the smart sensors use electrochemical cell detection, semiconductor detection, pyrolysis-particle detection, galvanic cell detection, and catalytic combustion detection.

The GD-70D Series features a large LCD display that easily reads all notifications and provides a color coded graph for alarm status (first and second alarms are red, and fault alarms are yellow). The LCD screen displays the pyrolyzer connection, gas concentration, detection unit of measurement, the detected gas, the maintenance status, sensor identification, the flow rate, a graph of gas concentration, error codes, and alarm points. All operational settings are completely user adjustable from the front panel. The unit also has a self-diagnosing function which detects sensor trouble and system failure. The Intelligent Gas Detector has a convenient troubleshoot feature through its firmware. This allows users to investigate and resolve their own equipment issues while minimizing maintenance costs.

Specifications

The Intelligent Gas Detector is a convenient size for workplace and wall space efficiency with dimensions of 2.8 D x 4.7 H x 5.9 D and weighs approximately 2 pounds. It can be mounted to a wall easily with a base plate and 2 or 3 screws. Sensor replacements and pump replacements can be performed quick and easily without tools.

*Please note we can only ship RKI products to customers within the United States

WC-1/3HPA WayCool 1/3 Hp Portable Evaporative Cooler with (ASO) Automatic Shut-off by Schaefer

WayCool® portable evaporative coolers use the natural cooling process of evaporating water to reduce temperatures up to 30°F at a fraction of the cost of air conditioning. WayCool blows cooled air in a focused narrow stream at high velocities long distances to provide greater cooling for employees, customers, guests, equipment and livestock both indoors and outdoors!

Features and Benefits:

• Oscillating outlet for greater coverage up to 4,700 square feet
• Approximately 75% lower energy consumption and 50% less expensive than the equivalent capacity portable air conditioner
• Automatic low water levels shut-off to prevent pump damage
• Built-in water reservoir for standalone use or connect to garden hose for continuous use
• Specially treated cellulose evaporative pads for extensive pad life
• 1 hp dimensions: Base 33" x 33" x 52" tall; 24 gallon reservoir
• 1/3 hp dimensions: Base 25" x 25" x 42" tall; 14 gallon reservoir
• 220V models available
• Two year warranty
• Made in the USA

SPSTAXA1 Sensepoint Detector with Junction Box, 0-50ppm Ammonia by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offers users a cost-effective solution to their gas monitoring needs, in or out of doors and even in potentially explosive atmospheres. Supplied with a pre-wired junction box, this detector can be installed using conduit or armoured cable and glands depending on the specific needs of the application.

Sensepoint flammable and toxic gas detectors are designed for use in potentially explosive atmospheres, and allow for easy access to terminals via the hinged lid of the junction box. Installation should follow national guidelines using suitably approved armoured cable and glands or conduit.

Supplied with an earth continuity plate for increased resistance to the effects of RFI, the junction box offers the installer a choice of 1/2", 3/4" and M20 connection via conduit or armoured cable and Ex e certified cable glands. Terminals are suitable for use with screened 0.5mm2 (20AWG) to 2.5mm2 (14AWG) cross sectional area cable, as needed to ensure minimum operating voltage at the detector, depending upon installed cable length.

Sensepoint flammable, toxic and Oxygen gas detectors are designed for direct connection with the Honeywell Analytics' range of Touchpoint controllers.

One-Stop Shop

• Flammable, toxic and Oxygen versions available
• Suitable for indoor or outdoor use
• IP65 as standard

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX Certified

• Complies with the latest European standards
• Hazardous area and performance approvals
• Can be used for uncertified applications

Easy to Use

• Factory set operation
• Simple sensor replacement
• Minimal training required

Friendly Installation

• Universal junction box
• One box, three entries
• Metric and NPT compatibility
• Includes earth continuity plate for enhanced protection against RFI

Range of Accessories

• Weather Housing (IP66)
• Flow adaptor
• Collecting cone

65-2641RK-12 M2A Stand Alone Sensor / Transmitter, Hydrogen Specific LEL, without Detector by RKI Instruments

The RKI M2A™ is a state-of-the-art transmitter that can operate as an independent, stand-alone monitor or as part of an integrated system. The M2A connects with an analog or digital signal to virtually any controller, PLC, or DCS. Setup procedures are simplified with user friendly push buttons and OLED menus. It utilizes a magnetic wand technique for performing non-intrusive calibration. The M2A provides an automatic zero drift correction feature, which results in more stable readings and reduces the need for adjustments due to sensor aging.

The housing of the M2A does not need to be opened for zeroing or calibration, making it unnecessary to declassify the area for routine maintenance. It is designed so that a complete field calibration can be performed by one person. Sensor construction is rated Class I, Div. 1 Groups B, C, D for flammables, CO, H2S, O2, and CO2, and Class I, Div. 2 for all other toxics.

The transmitter provides a 4-20 mA output in addition to a Modbus digital output. It also has two levels of alarms with relays, plus a fail alarm with relay. A digital display of the gas concentration, as well as alarm and status lights, can be viewed through the front window.

The toxic sensors are electrochemical type plug-in sensors, which provide high specificity, fast response, and long life. The plug-in design allows quick replacement in the field with no tools required. Toxic sensors are designed for use in Class I, Div. 2 hazardous locations. Sensors available for NH3, SO2, PH3, AsH3, and HCN.

The M2A represents the latest leading edge technology in sensor / transmitters today.

Features

• Operates with or without a controller
• Direct digital readout with OLED cold temperature display
• Available gases include LEL, O2, H2S, CO, CO2, and 100% Vol CH4 / Toxic gases include NH3, SO2, HCN, and more
• Infrared sensor for combustibles and CO2
• 4-20 mA & digital Modbus outputs standard
• 2 fully programmable alarm relays & fail relay
• Non-intrusive calibration via magnetic wand
• Explosion proof construction
• Patented water repellent sensor cover
• User friendly setup, push buttons & OLED menus
• Long-life sensors (2 + years typical)

*Please note we can only ship RKI products to customers within the United States

HC2000-1-3 20" Hood Style Exhaust Fan, Aluminum Shutter, High Capacity, 3-Phase by Schaefer

Do you need to move some air, but don't need a full sized exhaust fan?

The Schaefer fiberglass hood style exhaust fans are the perfect solution. These fans are designed for thin walled, modest sized facilities, including greenhouses, garages and workshops.

The fans mount on the inside the building. The shutter and weatherhood mount on the outside of the building and provide the ultimate weather protection for extended life and sustained performance.

Features and Benefits:

• Polypropylene fan blades for high performance and long life
• Integrated heavy-duty aluminum shutters for increased durability
• High quality, energy efficient, maintenance free motors for maximum performance and ease of use
• Molded, one-piece fiberglass weather hood for extended fan life and sustained performance (optional)
• Available in 12" 16" and 20" sizes
• Two year product warranty
• Made in the USA