Over $5000

*Please note we can only ship RKI products to customers within the United States

SS4-AUV2-C-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

FP-260AGZSL Paper Tape Machine, C4F6, Low Range by RKI Instruments

This model is a highly sensitive C5F8 / C4F6 / or C3F6 gas monitor which uses a special techniquie for detecting C5F8, C4F6 or C3F6. into more readily detectable compounds.

Then, the resulting compounds cause a chemical reaction on a colorimetric tape, and the intensity of the chemical reaction is analyzed and correlated to a specific ppm level of C5F8, C4F6 or C3F6 present in the sample. The detection tape is in a handy cassette which is easily removed for periodic replacement.

Features:

• Ideal for monitoring semiconductor fab clean rooms
• Ideal for low gas concentration
• Minimal interference from solvents such as Fluorinert and Galden
• Easily replaceable plug-in tape cassette
• Cassette tape remainder display included

Applications:

• Environmental Monitoring
• Semiconductor Fabs
• Manufacturing
• Detecting uncaptured gas from scrubber

*Please note we can only ship RKI products to customers within the United States

MCB3-A3C1REZ-02M MultiRAE Pro Pumped Portable Multi-gas Monitors - 10.6 eV ppb PID / LEL / CO + H2S / O2 / Gamma / Li-ion / Non-Wireless / Accessories Kit / Confined Space and Calibration Kit (4-gas + 10 ppm Iso) by RAE Systems

The MultiRAE Pro is the industry's only portable wireless multithreat monitor. The MultiRAE Pro's ability to simultaneously detect gamma radiation and toxic industrial chemicals (TICs/TIMs) enables responders to reduce the equipment footprint and achieve greater agility when operating downrange.

The MultiRAE Pro's optional wireless capability improves safety by providing commanders and safety officers real-time access to instrument readings and alarm status from any location for better situational awareness and faster incident response.

Key Features

• All-in-one monitoring capabilities for radiation, VOCs, oxygen, toxic and combustible gases, up to 6 threat types at a time
• Over 25 interchangeable sensor options, including parts-per-billion PID and gamma radiation
• Wireless access to real-time instrument readings and alarm status from any location
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Intelligent sensors store calibration data, so they can be swapped in the field
• Large graphical display with easy-to-use, icon-driven user interface

Applications

• Civil defense (search and rescue)
• Homeland security
• HazMat response
• Military
• Semiconductor manufacturing
• Environmental

H-D03-0010-000 RAEGuard 2 PID Transmitter Kit, UL, 0.1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

D03-0010-000 RAEGuard 2 PID Transmitter Kit, UL, 0.1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

3626-251 D-ReX PoS Gas Detector with 5 relays and Enclosure, Isobutylene (C4H8) MK463-10, 0.1 ppm, 0 - 200 ppm by GfG

The D-ReX is a very user-friendly, easy-to-maintain gas detector.

High-resolution, full-color display

The 2.4, 320 x 240 pixel full-color TFT display sets new standards for gas detectors. It provides clear and precise information about the current measured values, the short-term and long-term exposure, as well as any malfunctions that may have occurred. Information can be displayed in a variety of languages and scripts, including English, German and Simplified Chinese.

Clear Information

No longer will you have to decipher cryptic error codes – information on any issue is instead displayed in plain text. Status LEDs provide an additional instant overview of vital components of the system.

Intuitive device management using Bluetooth and app

Settings on the D-ReX can easily be managed using the configuration program or the GfG app (Android). They can be connected to the device either via RJ45 an interface or Bluetooth. This will give you access to all settings and configuration options. After entering the password, changes can also be made using the control keys in the D-ReX's service menu.

Advanced connectivity

The D-ReX comes with a wide variety of communication interfaces: Choose between analog, industry standard 4-20 mA, digital RS-485 interface (Modbus/RTU), Ethernet (Modbus/TCP) and LonWorks (optional) for signal transmission. The Bluetooth option enables wireless connectivity. In addition to the five internal, programmable changeover contact relays (optional), 16 additional relays can be addressed by connecting the D-ReX to a GMA200-RT/D relay module.

Periodic sensor self-tests

The plug-and-play smart sensor cartridges are pre-configured and pre-calibrated for easy installation or replacement. Automatic sensor self-tests increase safety while reducing maintenance costs even further.

The new Standard for Versatility: D-ReX

All the advantages mentioned perfectly qualify the D-ReX for numerous applications in virtually all industries. Some of its unique features make it particularly suitable for use in the semiconductor industry, photovoltaic industry and industrial manufacturing as well as in laboratories. If you are looking for the gas detector that best suits your needs, the D-ReX will be your first choice for many applications.

Possible areas of application:

• MRI Labs
• Process tools
• Vacuum pumps
• Scrubbers
• Gas cabinets
• Ambient breathing zones
• Storage areas
• Cleanroom environments
• Sub fab systems

Features:

• Sensors for more than 30 gases
• Hot-swappable smart sensor cartridge
• High-resolution, full-color 2.4" TFT display
• Plain text information
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Can be addresses via web portal
• Password-protected menu
• Interface: Analog: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarms history
• CE marked and UL certified

USPs:

• Tube length up to 30 m / 100 ft.
• Extension cable 1 m / 30 m
• Easy to replace mechanical component of internal pump
• Bluetooth®

Options:

• 16x external relays (GMA200-RT/D)
• Line Integrity Monitoring

27604 Si-CA 230 Analyzer, five gas sensors (O2, CO, NO, NO2, SO2) by Sauermann

With double the number of cells and expanded measurement capabilities, the Si-CA 230 is suited to the most powerful industrial machines. And with support for more gases and a high CO tolerance threshold, its versatility makes it the ideal choice across residential, commercial and industrial applications.

• Up to six gas sensors
• Total NOx & Low NOx Capable
• Field Replaceable Pre-Calibrated Sensors
• Large Color Touch Screen
• iOS and Android Mobile Apps for Real-Time Display & Control
• CO Dilution auto-range with measurements to 50,000 ppm
• Ergonomic, light weight, & durable design
• Data management with automatic logging & report creation
• Predictive maintenance with estimated sensor life & calibration reminders
• One touch pump On/Off with purge
• PC software with wireless and USB connectivity
• Auto pump cut-off for high CO levels
• Graphical data display
• Customizable gas analysis screen
• Sample conditioning unit for low NOx & high moisture applications
• Stack gas velocity with Pitot tube
• Draft & differential pressure measurements
• Emissions values adjusted for reference O₂
• CO & CO₂ Monitoring in Ambient Air
• Hose extensions for tall & difficult to reach stacks
• Wireless Printer
• Protective rubber holster
• Maintenance contracts and extended warranties available

Kit Includes:

• 1 Si-CA 230 analyzer
• 1 O₂ gas sensors
• 1 CO gas sensors
• 1 CO Dilution Auto-Range to 50,000 ppm
• 1 Protective rubber holster
• 1 300 mm flue gas probe with 3 m dual hose (other probe lengths available)
• 1 Water trap with filter
• 1 AC power supply / charger
• 1 USB cable
• 1 Mobile app & PC software
• 1 Internal wireless communication module
• 1 Carrying case
• 1 Quick Start Guide
• 1 Calibration certificate

MX6-P425R201 MX6 iBrid Multi-Gas Monitor, HC (IR-Propane), NO2, H2S, SO2, PID, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, No Pump, English by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

SS4-AUV2-C-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV, FM, Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Non-latching Alarm LED, FM, cFM, IECEx Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AUV2-SS Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV, FM Hydrocarbon & Non-Hydrocarbon Fires, indoor applications, Nonlatching Alarm LED, FM, cFM, CSFM for C1, D1, Groups B,C,D (2) 3/4 NPT by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

LPV440-99-00012 Spectrophotometer, Benchtop DR3900 by AquaPhoenix

Expert water analysis made simple.

Simple Preparation

• TNTplus vials use Dosicaps - freeze-dried reagents integrated into sealed cap - that are easier to use than Powder Pillows or Liquid Reagents, without any risk of contamination.
• The boxes and vials are color-coded for a fast and easy parameter and range recognition of exactly the test you need.
• Step-by-step illustrated test methods are printed on the box as a quick reference and can also be called up in the instrument menu.

Fast execution

A 2D barcode on the TNTplus vial is automatically read by the Hach DR spectrophotometer to identify the appropriate method and take the measurement. The vial spins to take 10-fold absorbance readings that will be averaged for result determination to exclude scratches and fingerprints. Instrument calibration verification and high instrument stability all combine to eliminate the need to run reagent blanks.

Comprehensive Documentation

• Measurement results are documented on the detailed level with timestamp, operator ID, absorbance reading, and calculated concentration. The 2D barcode delivers the lot number and expiry date, logged with every result.
• For your accreditation the certificate of analysis can be called up just by wiping the reagent box towards the RFID* sensor.

*RFID technology currently available in US, Canada, Puerto Rico, Australia, New Zealand, and Colombia only.

3615-203 D-ReX PoL Gas Detector with 5 relays and Enclosure, Carbon dioxide (CO2) MK252-10, 0 - 25% vol. by GfG

The D-ReX is a very user-friendly, easy-to-maintain gas detector.

High-resolution, full-color display

The 2.4, 320 x 240 pixel full-color TFT display sets new standards for gas detectors. It provides clear and precise information about the current measured values, the short-term and long-term exposure, as well as any malfunctions that may have occurred. Information can be displayed in a variety of languages and scripts, including English, German and Simplified Chinese.

Clear Information

No longer will you have to decipher cryptic error codes – information on any issue is instead displayed in plain text. Status LEDs provide an additional instant overview of vital components of the system.

Intuitive device management using Bluetooth and app

Settings on the D-ReX can easily be managed using the configuration program or the GfG app (Android). They can be connected to the device either via RJ45 an interface or Bluetooth. This will give you access to all settings and configuration options. After entering the password, changes can also be made using the control keys in the D-ReX's service menu.

Advanced connectivity

The D-ReX comes with a wide variety of communication interfaces: Choose between analog, industry standard 4-20 mA, digital RS-485 interface (Modbus/RTU), Ethernet (Modbus/TCP) and LonWorks (optional) for signal transmission. The Bluetooth option enables wireless connectivity. In addition to the five internal, programmable changeover contact relays (optional), 16 additional relays can be addressed by connecting the D-ReX to a GMA200-RT/D relay module.

Periodic sensor self-tests

The plug-and-play smart sensor cartridges are pre-configured and pre-calibrated for easy installation or replacement. Automatic sensor self-tests increase safety while reducing maintenance costs even further.

The new Standard for Versatility: D-ReX

All the advantages mentioned perfectly qualify the D-ReX for numerous applications in virtually all industries. Some of its unique features make it particularly suitable for use in the semiconductor industry, photovoltaic industry and industrial manufacturing as well as in laboratories. If you are looking for the gas detector that best suits your needs, the D-ReX will be your first choice for many applications.

Possible areas of application:

• MRI Labs
• Process tools
• Vacuum pumps
• Scrubbers
• Gas cabinets
• Ambient breathing zones
• Storage areas
• Cleanroom environments
• Sub fab systems

Features:

• Sensors for more than 30 gases
• Hot-swappable smart sensor cartridge
• High-resolution, full-color 2.4" TFT display
• Plain text information
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Can be addresses via web portal
• Password-protected menu
• Interface: Analog: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarms history
• CE marked and UL certified

USPs:

• Tube length up to 30 m / 100 ft.
• Extension cable 1 m / 30 m
• Easy to replace mechanical component of internal pump
• Bluetooth®

Options:

• 16x external relays (GMA200-RT/D)
• Line Integrity Monitoring

4050012 PSS 7000 Sentinel 7000 LP QC NFPA 2018 by Draeger

Before you can protect the lives of others, you have to protect yourself. The Draeger PSS® 7000 self-contained breathing apparatus (SCBA) provides unmatched comfort, durability, and safety in the harshest environments. With unparalleled ergonomic performance, the PSS® 7000 combines trusted pneumatics, flexible fit, and cylinder Quick Connection, freeing the firefighter to concentrate on the task at hand.

Built to satisfy the most rigorous demands

Based on feedback from firefighters throughout North America, the Draeger PSS 7000 SCBA with the Sentinel 7000 monitoring system satisfies the most rigorous demands of today's complex fire grounds. first responders. Backed by a 15-year, bumper-to-bumper warranty, the Draeger PSS 7000 distinguishes itself from other SCBAs in the marketplace with ergonomic performance, clean-ability, and toughness.

Innovative harness system provides unmatched comfort and durability

The Draeger PSS 7000 SCBA is designed so the heaviest components sit at a lower center of gravity to increase stability and balance, allowing the wearer to work more effectively with less fatigue. The PSS 7000 includes an adjustable harness suspension system that provides the ultimate in comfort and extended wear. Durable webbing and advanced compression-molded comfort padding offer up to 6.5-times higher abrasion resistance than traditional padding. The material surface is easy to clean and disinfect with a highl resistance to chemical and mechanical damage.

The harness has a high-grip, anti-slip inner surface that stays securely in place without a chest strap or having to over-tighten the shoulder straps. Cooling channels in the shoulder straps and waist belt reduce the likelihood of compression burns. A stainless-steel, harness-friction buckle makes the SCBA easy to don and doff.

Ergonomic three-position backplate allows freedom of movement

The Draeger PSS 7000 is designed to move with the wearer allowing unrestricted movement while walking, crawling, or climbing. The backplate automatically lengthens and pivots to mirror wearer movements. The unique, self-adjusting and pivoting waist belt keeps the SCBA on the hips when a firefighter reaches, preventing your coat from riding up.

To reduce back strain, the SCBA's weight is designed to ride on the hips. The three-position, carbon-fiber composite backplate adjusts to comfortably fit different torso lengths.

A slide-and-lock harness mechanism allows the harness and waist belt to be connected or removed from the backplate quickly without tools. To minimize the risk of snagging or damage, supply hoses are integrated neatly into the backplate.

Rapid, secure cylinder change-outs save precious time

The PSS 7000 has a lock-and-load system that lets colleagues securely change out cylinders quickly. A proven, quarter-turn QuickConnect adapter allows quick and easy attachment of the cylinder to the reducer, saving time compared to conventional threaded reducer hand-wheel-and-cylinder CGA connections. QuickConnect features a safety interlock system that prevents disconnection at pressures above approximately 70 psi.

Draeger Sentinel 7000–Real-time monitoring

The Sentinel 7000 electronic monitoring system provides options to satisfy the needs of any fire department. Incorporating a centralized power supply and pressure sensor module within the backplate, the robust system combines maximum component protection with balanced weight distribution for reduced physical stress.

Housed in impact-resistant, water-resistant casings, the Sentinel 7000 demonstrates excellent reliability on the fire ground.

An electronic gauge provides real-time monitoring of essential information, including:

• A personal alert safety system (PASS) device
• Intuitive push-button operation for ease of use
• Configurable settings to suit individual preferences
• Data logging for improved post-incident analysis
• Accurate, continuously updated digital display of pressure and time to EOSTI activation (time based on dynamic breathing rate)
• Battery status display
• 360° visual and audible alarms triggered when the PASS is activated
• Automatic self-tests and system tests

MMT-LB01 Midas-M 4-20mA and TCPIP Modbus Transmitter with Tube by Honeywell Analytics

Bringing new visibility, reliability, and easeof-use to gas detection in semiconductor processing and industrial manufacturing.

An easy-to-use, cost-effective addition to the Honeywell gas detection portfolio, the Honeywell Midas®-M Gas Detector uses reliable sensor technology to detect more than 35 key toxic, ambient, and flammable gases - easily, quickly, and error-free.

The device monitors points up to 30 meters (100 feet) away while using patented technology to regulate flow rates and ensure error-free gas detection.

The standard power supply and communications capabilities include three onboard relays (Form C), 0 mA to 21 mA analog output, and Modbus®/TCP Ethernet digital outputs for easy connectivity to control and alarm systems' ports for optimal connectivity and service interaction.

With flexible features and options, the Midas-M Gas Detector works right out of the box and configures easily to meet your needs. Each plug-and-play sensor cartridge is pre-calibrated, so it's ready when you are. That means longer sensor life, quick-and-easy replacement, and no operator error due to incorrect or depleted sensors. With the Midas-M Gas Detector, customers can get extended sensor calibration periods, patented diagnostics, and lower cost of ownership.

FEATURES AND BENEFITS

• CLEAR VISIBILITY: The Midas-M Gas Detector is equipped with bright LEDs and an intuitive interface that provides instant alerts to gas readings or alarm levels.
• CALIBRATION COMPLETED: Factory-calibrated sensors reduce need for frequent gas testing.
• EASY INSTALLATION: Compact in size making it suitable for crowded, complex process environments where space is at a premium, the Midas-M Gas Detector is simple to install with its plugand-play capability.
• POE PROTOCOL: The detector includes the innovative Power over Ethernet (PoE) protocol - a single Ethernet connection for all power, control and communication requirements.
• INTEGRATED SECURITY: The Midas-M Gas Detector's interface includes passwordprotected menus to maintain system integrity.

APPLICATIONS

• Semiconductor processing
• Light industrial manufacturing
• University laboratories
• Aerospace
• Wastewater

MX6-8426P215 MX6 iBrid Multi-Gas Monitor, ClO2, NO2, H2S, NH3, HC IR, Lithium-ion Extended Runtime battery (UL/CSA/ATEX/IECEX), Aspirated (pump), Italian by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm