GfG

2109-100 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 100 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2200-003W GMA 200-MW16 Controller, Configured for 3 Measuring Points, Supply Voltage 24 V/DC, without Power Supply by GfG

The GMA 200-MW is our most flexible and advanced gas detection system controller. The design of the GMA 200-MW ensures simple and clearly structured operation in industrial and commercial applications. The system can be configured for control of any combination of GfG gas transmitters for the measurement of an extremely wide range of toxic and combustible gases and vapors.

Flexible modular design

Each GMA 200-MW module can control up to 16 individual gas transmitters (sensors). The self-contained, IP-65 wall-mounted housing facilitates cost-effective and space-saving installation. GMA 200-MW systems are scalable, and easy to expand by adding additional controller and relay modules. Optional gateway modules allow control via remote or touch-screen computer interface.

Easy to configure

Easy-to-use, menu driven GMA 200-MW software allows configuration of sensor type, gas type, measuring point designations, units of measurement, calibration curves, and function of the comprehensive and fully programmable relays. Up to three individual or specified alarm thresholds can be programmed for each measuring point. The GMA 200-MW continuously evaluates the analog input signals of the connected detectors.

Integrated relays

GMA 200-MW systems include comprehensive and fully programmable relays. Each controller is equipped with 8 internal relays. Menu-driven software allows easy assignment of measuring points to relays, single or multiple alarms per point, alarm thresholds, configuration of collective or group alarms, zoning, fault messages and voting functions.

Relay modules

GMA 200-RW relay modules are housed in easy to install IP-65 wall mounted enclosures. Each relay module provides an additional 16 freely configurable relays. A total of four additional relay modules (for 64 additional relays) can be managed by the same GMA 200-MW system. Digital connection with the GMA 200-MW controller allows remote positioning of the relay module wherever it makes the most sense, substantially reducing cabling and installation costs.

Remote terminal displays

Relay modules are available with or without an integral display for readings and system information, making it easy to add a remote terminal wherever needed.

Optional Fieldbus-Gateways

Optional gateway modules allow integration of the GMA 200-MW system into existing company networks based on TCP/IP, Process Field Bus or Process Field Network protocols. Monitoring and system performance data are easily exported for viewing or analysis. A wifi interface can be added to the gateway to allow wireless connection with a touch screen Windows® computer or smart-phone to display or access system information.

GMA 200 power options

GMA 200-MW power options include traditional voltage inputs (2 x 24 V DC, 20-30 V), as well as operation via a redundant, uninterruptible power supply (UPS), ensuring continued operation of the gas warning system even during a power outage.

Integral alarms

The GMA 200-MW includes built-in bright LED strobe light and loud audible alarms.

LED indicator lights

The status of the GMA 200-MW system (including operation, fault, service, alarm and relay status) is shown via LEDs. Individual LED indicators identify the type and severity of the alarm condition, (FLT, AL1, AL2, AL3), and any relays activated by the condition, (R1 through R8).

Datalogging standard

Measured values, mean values, alarm events and faults are permanently stored on a microSD memory card.

Graphical display

Currently measured values are displayed on a backlit, graphical LCD. In the event of an alarm the display changes color from green to red, and highlights the affected channels.

Five buttons enable operation at the GMA 200-MW controller. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the controller, detector and the relays can be retrieved in the operating menu.

Operation via keypad

Operation of the GMA 200-MW is through easy-to-use menus, and a simple 5 button interface for alarm acknowledgement, and viewing information on the status of the gas warning system, detectors and relays. The intuitive push-button controls make it easy to navigate through additional screens of information. The integrated display enables the reading of alarm levels through the controller LCD for easy hazard assessment.

Configuration

A built-in USB port in the GMA 200-MW is used for connection to the configuration software. GMA 200-MW systems connected through a Fieldbus gateway can be remotely connected with a GfG factory service center for configuration, diagnostic or service evaluation.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Additional modules available in IP-65 wall-mounting housings

• External relay module: GMA 200-RW
• Independent power supply: GMA 200-UPS
• Continuous, motorized pump sampling unit: GMA 200-ASV
• Fieldbus gateway: GMA 200-GW

Features

• Advanced and flexible controller for combustible, O₂ and toxic gas
• IP-65 wall-mounting housing, with integral audible and LED alarms
• Flexible, reliable and economic
• Up to 16 transmitters per GMA 200-MW controller in any combination
• Freely programmable relays
• Clearly structured, easy-to-use push-button interface
• Backlit graphic LCD changes color to indicate alarm
• Connect to other measurement devices with 4-20 mA output

G460-11-03-24-00-66 G460 Multi-Gas Detector with NiMH Smart Pump and NiMH Battery with Flashlights, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, NO2 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

3711-100SE Dynagard Stand-alone System, Ammonia (NH3), 1 ppm, 0 - 100 ppm by GfG

Single-point Area Monitors

Dynagard AutoCal^® monitors are single point detection instruments that accurately measure toxic gases and oxygen levels. Alarm lights on the front panel illuminate and an internal horn sounds when gas concentrations are exceeded.

Simple and effective

The units accurately display values on a large backlit LED and can transmit a linear 4-20 mA output. AutoCal® calibration and maintenance is done effortlessly through front panel push-buttons. Smart sensors enable the user to change measuring ranges or gas types in the field without a need for additional programming. The Dynagard is equipped with onboard relays for two adjustable alarm points. It also has one sensor fault for local connection and activation or deactivation of external devices like strobes, fans, auto dialers etc.

Features

• AutoCal® automatic calibration
• Smart sensor technology
• Digital display / control connection
• Internal push-button alarm settings

G460-11-03-70-00-24 G460 Multi-Gas Detector with Alkaline Smart Pump and NiMH Battery, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, PID by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

2801-31-002 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Heptane (C7H16), Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

G460-11-03-10-00-24 G460 Multi-Gas Detector with Alkaline Smart Pump and NiMH Battery, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, SO2 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

4021-DP-PR RAM 4021 Respiratory Air Monitor, Dew Point, Complies with NFPA 99 C-26 (5.1.3.5-15) by GfG

The RAM 4021 AutoCal® series is the unit of choice where specific and accurate measurement of carbon monoxide, oxygen or dew-point levels are required. Designed to meet OSHA requirements for monitoring of Grade D respirable air, this unit is equipped with a reliable electrochemical sensor that accurately indicates the level of carbon monoxide on an illuminated liquid crystal display. Adding versatility, this unit offers optional oxygen or dew point sensors for applications where detection or measurement is needed.

Calibration and maintenance are simple with our innovative AutoCal® system. Additional features including alarm relay contacts, user adjustable alarm point, low flow alarm indicator and many more make this unit an intelligent choice. The RAM 4021 is available in four models, the 4021 (CO), 4021-1 (CO and O2), 4021-DPX (CO and dew point levels) and 4021-PR (CO and additional relay to signal power loss to monitor, complies with newest NFPA regulation). All models may be purchased with or without airline filter systems

Respiratory air specifications

All GfG Instrumentation RAM Instruments satisfy the requirements of OSHA rule 29 CFR 1910.134 (d) (2) (ii) for carbon monoxide monitoring. They will also monitor Grade E air, generally specified for breathing air in cylinders (SCBA).

Wall mounted filter panel option

The 25, 50 and 100 CFM panels filter out dangerous toxins from supplied air sources and ensure clean, breathable air. The threestage filter system efficiently removes particulates, oil vapors and hydrocarbons from an air supply. After filtration, the regulator sets the pressure for the respiratory equipment and the manifold assembly provides multiple outlets for airline hose quick connections. The model 8025 panel includes two user female quick connect outlets; the 8050 includes four, and the 8100 includes eight. A 1/2" FPT connection is standard on all 50 and 100 CFM panels, and a 3/8" FPT connection is standard on all 25 CFM panels.

Features

• Continuous compressed air CO monitor
• Integrated dew point measurement
• Robust easy-to-operate design

Features

• RAM 4021 Monitor
• Carbon monoxide (CO) sensor
• Other sensors (as specified)
• Manual

G460-11-03-24-00-44 G460 Multi-Gas Detector with Alkaline Smart Pump and NiMH Battery with Flashlights, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, NO2 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

G460-11-03-24-00-40 G460 Multi-Gas Detector With NiMH Battery with Flashlights, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, NO2 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

2811-709-001 EC 28 Gas Transmitter with Sensor, Chlorine (Cl2), No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2109-1000 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 1000 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

G460-01-03-29-61-44 G460 Multi-Gas Detector with Hand Aspirated Pump and NiMH Battery with Flashlights, O2, IR LEL, CO and H2S Sensor, H2 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

2801-20-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-4% by Volume (MK 208-1), Ammonia (NH3), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

3511-200 EC 35 Fixed Gas Transmitter, Ammonia (NH3) for Low Temperatures (-40°F to 60°F), 2 ppm, 0-200 ppm, Display by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment

G460-11-01-02-60-44 G460 Multi-Gas Detector with Alkaline Smart Pump and NiMH Battery with Flashlights, O2, Catalytic Combustion LEL Sensor, CO, H2S, CO2, NDIR by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.