GfG

2811-4501-004 EC 28 Gas Transmitter with Sensor, Ammonia (NH3), 0-100 ppm, Display / Alarm / Relay by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2801-36-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Pentane (C5H12), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

1316-004 G315 Single Gas Detector for Toxic Gases, Optimized for Ammonia (NH3) with NiMH Rechargeable Battery Pack by GfG

Pinpoint the Smallest Leaks

Small leaks in pipes or storage tanks can release enough gas to build up dangerous concentrations. The careful inspection of flanged, threaded and soldered connections before and after installation will ensure equipment and worker safety. The G300 leak detector will make leakage sprays a thing of the past

Clear and simple displays and warnings

Changing gas concentrations are indicated audibly and visually. The frequency of the audible warning rises with gas concentrations, allowing the user to pinpoint leaks. The bar graph display will warn the user if dangerous gas concentrations arise.

Light, compact and durable

Designed for one-handed operation, the G300 reacts to concentrations as small as 5 ppm and measures up to more than 10,000 ppm or 1% volume. The sensor is located at the end of a flexible gooseneck or a helix cable to allow the user to reach difficult or unreachable locations. The G300 is available with or without explosion protection for ammonia and combustible gases. The G311 operates on four "AA" alkaline batteries. All others have a rechargeable battery with run times of more than eight hours.

Features

• Small, light, and durable leak detector
• For combustible gases and ammonia
• More than 8 hours of continuous operation
• Explosion-proof models available

Standard Accessories

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

1450-602 TS400 Test Station - Instrument & Pump Includes Tubing, Software, USB Cable and Manual by GfG

Easy operation

The operation of the TS400 test station couldn't be any easier. Simply place the G450 or the G460 in the station and the system will take over from there. The TS400 automatically performs a full functional test that includes performance of all sensors and alarms.

Extensive diagnostics

The TS400 is designed to go beyond the traditional basic bump test and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the TS400 you can have confidence with this added level of safety.

Charging option

The TS400 is available (optionally) for use as a charger as well as a test station. After all tests have been completed you may remove and begin using the detector or leave it in the TS400 for recharging.

Record Keeping

A good gas detection instrument maintenance program is not complete without equally good record keeping. Whether you choose to download the records, maintain the records on a PC / network or your preference is to leave the work to the test station, the TS400 is the right choice.

The TS400 can retain as many as 2 million complete diagnostics in memory with the maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The TS400 is designed to reduce the cost of ownership every step of the way. The push button regulator helps to sharply reduce the amount of gas required to test your instruments.

PC communication

The TS400 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

The TS400 software includes a module to quickly print official bump test certificates. Simply download the records from the TS400 and start the "Certificate Generator" it takes only seconds!

Detector with Pump

The TS400 is available for use with the instrument only or there is an available design for use with the instrument with a pump. There is no need to remove the pump before placing the detector in the test station.

Features

• Four test gas ports
• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Cascade multiple docking stations
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

2811-727-002 EC 28 Gas Transmitter with Sensor, Oxygen (O2), Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2811-731-003 EC 28 Gas Transmitter with Sensor, Sulfur Dioxide (SO2), Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2214018 CS 21 Fixed Gas Transmitter, HFC-23 (CHF3), 30 to 1000 ppm by GfG

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants
• Long sensor life
• Fast response

1418-115 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Nitric Oxide (NO), 0 - 100 ppm by GfG

Durable, compact design

Widest Range of sensors

Easy Operation

Up to six months of battery life

Clip-on attachment

Optional motorized pump

Large graphic display

Audible, vibrating and visual alarms

Lifetime warranty

DS220 docking station

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

4435-1-3 4400-C 4-channel Controller Panel with Three EC 35 Transmitters by GfG

The 4100 one-channel and the 4-channel 4400 gas warning systems offer safe and reliable gas detection.

Alarm points

Each alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The alarm point values can be freely adjusted within the detection range of the transmitter. Every alarm point value can be selected to be latching / non-latching or resettable / non resettable.

Alarm relays

The controller provides four voltage-free relays for the three alarms in addition to one fault warning. The relays may be used to control additional alarm devices like lights or horns. They can even prompt specific counter measures to prevent or limit dangers from gases or vapors.

Features

• Complete 1-to-4 channel controller / gas monitoring system
• 110 VAC or 24 VAC
• Case-mounted horn / strobe
• Security lock
• Slim-line design

Additional features

The 4100 control panel stores peak values and offers an additional 4-20 mA output. The 4400 control panel offers the ability to connect up to 4 transmitters and comes standard with an additional 24 VAC output for solenoid control.

2811-707-003 EC 28 Gas Transmitter with Sensor, Carbon Monoxide (CO), Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2801-05-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Diethyl ether (C4H10O), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

G460-01-01-02-64-44 G460 Multi-Gas Detector with Alkaline Smart Pump and NiMH Battery with Flashlights, O2, Infrared LEL Sensor / % Vol., CO, H2S, CO2, NDIR by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

2811-4505-002 EC 28 Gas Transmitter with Sensor, Ammonia (NH3), 0-500 ppm, Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

G460-01-03-70-64-20 G460 Multi-Gas Detector With NiMH Battery, O2, Infrared LEL Sensor / % Vol., CO and H2S Sensor, PID, CO2 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

2901-21-005 IR 29 Di Gas Transmitter with Display, with Pressure and Humidity Compensation, IP67, Acetylene (C2H2), 0 - 100 LEL by GfG

Measuring Principle

IR transmitters have become recognized as reliable gas warning systems for explosion protection. They are used to detect individual combustible gases or a wide range of gases. This involves sending an IR beam with a certain light intensity through a measuring space and then capturing it with a detector. Parts of this beam are absorbed by, amongst other things, hydrocarbon molecules. The reduced light intensity of the beam is registered by beam detectors and converted into a signal as the existing % LEL gas concentration.

Benefits

A special feature of our IR technology is its ability to also measure combustible gases above the lower explosion limit. Moreover, the measurement does not require oxygen.

With this technology there is basically no risk of contaminating the sensor, through silicone vapors or hydrogen sulfide, when using catalytic combustion sensors.

Operation

IR transmitters are usually used with 2 wavelengths, a so-called reference wavelength and just one measuring wavelength. Strict limits are applied to these systems. The absorption spectra of many hydrocarbons are located in the wavelength range of 3.3 μm and overlap to a large extent.

This means that gases with overlapping spectra and just one measuring wavelength can no longer be clearly distinguished. Some hydrocarbons, e.g. the frequently used welding gas acetylene, are non-absorbing in the wavelength range of 3.3 µm, but absorb instead in neighboring wavelength ranges.

In many practical applications, it is not essentially important which gas is responsible for the explosion risk. Therefore, early warnings through the broadband measurement of hydrocarbons in order to monitor the lower explosion limit (LEL) must be guaranteed. False alarms with uncritical concentrations of individual gases or solvents are thus absolutely unacceptable.

These requirements are problems for systems with 2 wavelengths.

Patented GfG Technology

The internationally patented technology of the IR 29 has been developed to solve these problems. The gold-plated mirror optics of the sensor contains 2 radiators and up to 4 detector elements with different optical filters. The precisely calculated, microstructured and pure gold coated mirror optics of the IR 29 are supplied for the first time without beam splitters.

This helps to cut signal losses by 50 % and to completely avoid the physically-related disadvantages of a beam splitter. The measured values from two additional wavelengths (4 wavelengths in total) ensure improved detection of individual gases and thus enhanced selectivity. This results in the prevention of false alarms. Only a 4 wavelength system always guarantees early warnings and the simultaneous prevention of false alarms.

New Technology

The IR 29 is the first and only intrinsically safe IR gas transmitter with patented 4-beam 4-wavelength technology.

The ignition protection class "intrinsically safe", which is so essential for industrial plants and the mining industry, is achieved by the additional use of the SB1 safety barrier and its internationally patented and innovative design.

Complete Safety Even In Zone 0

The IR 29 is the first IR gas transmitter that can also be used in Ex zone 0 and which enables maintenance as well as replacement of the sensor head without additional expense when energized.

Universal Application

The IR 29 with its robust V4A stainless steel housing has been designed to withstand the harshest environmental conditions.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Internal Data Logger

A standard built-in data logger records all the measuring data, minimum / maximum values, average values and alarm events of the last 24 hours in a ring buffer.

The recording can also be shown on the display as a 2 and 8 hour trend indicator.

The histogram mode can be selected as a permanent display of the measured values. These values are continuously updated.

Graphical Display

Measured values are shown on the high-contrast graphical display. The display can be rotated 180° depending on the installation of the IR 29.

Self Diagnosis

Processor-based signal processing enables the systematic compensation of temperature dependencies, aging influences and soiling effects. Safety-relevant functions are monitored permanently via self-diagnosis procedures and a possibly required service is indicated automatically. Daily interfering factors, such as dust and dirt accumulation, are almost completely eliminated by the innovative design.

Pressure Sensor, Moisture and Temperature Compensation

The measuring accuracy of IR sensors depends on partial pressure and thus also air pressure. Climatic fluctuations or barometric high pressure therefore influence the measuring result. Furthermore, the absorption spectrum of water almost completely covers that of hydrocarbon absorption in the 2.7 to 3.3 μm range. Air humidity therefore initially generates a measuring signal the same as the actual measuring gas. This cross-sensitivity is of particular importance in warm areas with high relative humidity. An increase in the absolute water absorption capacity of air is not linear with the temperature, i.e. three times as much water can be absorbed at 40 °C than at 20 °C. This influence can only be compensated if the current moisture content of the air is known. The IR 29 can be optionally equipped with a pressure and moisture sensor for compensation.

Maximum Safety

The innovative display enables the realization of completely safe warning concepts.

Local displays and signals directly at the device can be used to provide an early warning of potential risks.

The display at the upstream safety barrier SB1 D enables the detection of risks outside the danger zone being monitored.

This allows immediate on-site action before really hazardous situations occur.

Dust Protection

A gas permeable, water-repellent diaphragm protects the absorption space of the transmitter against dust. The additional impact protection made from robust V4A stainless steel prevents mechanical damage to the optical components.

The diaphragm can be cleaned or replaced in a matter of minutes.

Remote Controls

The IR 29 transmitter does not feature control elements for setting or servicing tasks. This helps to prevent accidental or unauthorized manipulation.

Service work at the IR 29 transmitter is carried out using the RC 2 remote control.

Features

• First intrinsically safe infrared transmitter for explosion protection
• ATEX II 1G Ex ia IIC T4 Ga C0158 can also be used in Ex zone 0
• Temperature, moisture and pressure compensation
• Patented infrared technology (NDIR)
• The energized IR sensor head can be replaced in Ex areas
• Maintenance and service-friendly

2811-707-004 EC 28 Gas Transmitter with Sensor, Carbon Monoxide (CO), Display / Alarm / Relay by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2811-736-004 EC 28 Gas Transmitter with Sensor, Hydrogen Chloride (HCl), Display / Alarm / Relay by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

G460-11-03-70-00-20 G460 Multi-Gas Detector With NiMH Battery, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, PID (0.5-2000) by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.