GfG

2811-731-004 EC 28 Gas Transmitter with Sensor, Sulfur Dioxide (SO2), Display / Alarm / Relay by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2801-20-002 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-4% by Volume (MK 208-1), Ammonia (NH3), Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

4435-1-2 4400-C 4-channel Controller Panel with Two EC 35 Transmitters by GfG

The 4100 one-channel and the 4-channel 4400 gas warning systems offer safe and reliable gas detection.

Alarm points

Each alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The alarm point values can be freely adjusted within the detection range of the transmitter. Every alarm point value can be selected to be latching / non-latching or resettable / non resettable.

Alarm relays

The controller provides four voltage-free relays for the three alarms in addition to one fault warning. The relays may be used to control additional alarm devices like lights or horns. They can even prompt specific counter measures to prevent or limit dangers from gases or vapors.

Features

• Complete 1-to-4 channel controller / gas monitoring system
• 110 VAC or 24 VAC
• Case-mounted horn / strobe
• Security lock
• Slim-line design

Additional features

The 4100 control panel stores peak values and offers an additional 4-20 mA output. The 4400 control panel offers the ability to connect up to 4 transmitters and comes standard with an additional 24 VAC output for solenoid control.

2901-21-006 IR 29 e (Increased Safety) Transmitter with Pressure & Humidity Compensation, IP 67, Acetylene (C₂H₂), 0 - 100% LEL Range, No Display / 4-20 mA by GfG

Unlike traditional LEL sensors, IR 29 transmitters do not need the presence of oxygen to detect gas. Since they are not affected by sensor poisons they don't require periodic adjustment to make up for lost sensitivity. The IR 29 continuously monitors its functions for proper performance, and can even identify and communicate required service procedures.

Features

• ATEX: II II 2G Ex eb mb ib [ib] IIC T4 Gb
• Patented infrared technology (NDIR)
• Temperature, moisture and pressure compensation
• Maintenance and service-friendly
• 4-20 mA, linear or digital (Modbus interface)

2801-34-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Methylisobutylketone (C6H12O), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-38-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Propylene (C3H6), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

4121-1 4100-C Single Channel Controller Panel with One ZD 21 Transmitter by GfG

The 4100 one-channel and the 4-channel 4400 gas warning systems offer safe and reliable gas detection.

Alarm points

Each alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The alarm point values can be freely adjusted within the detection range of the transmitter. Every alarm point value can be selected to be latching / non-latching or resettable / non resettable.

Alarm relays

The controller provides four voltage-free relays for the three alarms in addition to one fault warning. The relays may be used to control additional alarm devices like lights or horns. They can even prompt specific counter measures to prevent or limit dangers from gases or vapors.

Features

• Complete 1-to-4 channel controller / gas monitoring system
• 110 VAC or 24 VAC
• Case-mounted horn / strobe
• Security lock
• Slim-line design

Additional features

The 4100 control panel stores peak values and offers an additional 4-20 mA output. The 4400 control panel offers the ability to connect up to 4 transmitters and comes standard with an additional 24 VAC output for solenoid control.

2801-20-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-4% by Volume (MK 208-1), Ammonia (NH3), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-33-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Methyl acetate (C3H6O2), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

4000-1114 4000 Series Integrated Controller, 7 Channels, 3 Amp Power Supply by GfG

The 4100 one-channel and the 4-channel 4400 gas warning systems offer safe and reliable gas detection

Alarm points

Each alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The alarm point values can be freely adjusted within the detection range of the transmitter. Every alarm point value can be selected to be latching / non-latching or resettable / non resettable.

Alarm relays

The controller provides four voltage-free relays for the three alarms in addition to one fault warning. The relays may be used to control additional alarm devices like lights or horns. They can even prompt specific counter measures to prevent or limit dangers from gases or vapors.

Additional features

The 4100 control panel stores peak values and offers an additional 4-20 mA output. The 4400 control panel offers the ability to connect up to 4 transmitters and comes standard with an additional 24 VAC output for solenoid control.

Features

• Complete 1-to-4 channel controller / gas monitoring system
• 110 VAC or 24 VAC
• Case-mounted horn / strobe
• Security lock
• Slim-line design

4100-C Single Channel Controller Panel by GfG

The 4100 one-channel and the 4-channel 4400 gas warning systems offer safe and reliable gas detection.

Alarm points

Each alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The alarm point values can be freely adjusted within the detection range of the transmitter. Every alarm point value can be selected to be latching / non-latching or resettable / non resettable.

Alarm relays

The controller provides four voltage-free relays for the three alarms in addition to one fault warning. The relays may be used to control additional alarm devices like lights or horns. They can even prompt specific counter measures to prevent or limit dangers from gases or vapors.

Features

• Complete 1-to-4 channel controller / gas monitoring system
• 110 VAC or 24 VAC
• Case-mounted horn / strobe
• Security lock
• Slim-line design

Additional features

The 4100 control panel stores peak values and offers an additional 4-20 mA output. The 4400 control panel offers the ability to connect up to 4 transmitters and comes standard with an additional 24 VAC output for solenoid control.

2801-26-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), 2-Butanon (MEK) (C4H8O), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-24-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Butane-iso (C4H10), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-30-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Ethanol (C2H6O), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

3715-001 Dynagard Stand-alone System, Ozone (O3) by GfG

Single-point Area Monitors

Dynagard AutoCal^® monitors are single point detection instruments that accurately measure toxic gases and oxygen levels. Alarm lights on the front panel illuminate and an internal horn sounds when gas concentrations are exceeded.

Simple and effective

The units accurately display values on a large backlit LED and can transmit a linear 4-20 mA output. AutoCal® calibration and maintenance is done effortlessly through front panel push-buttons. Smart sensors enable the user to change measuring ranges or gas types in the field without a need for additional programming. The Dynagard is equipped with onboard relays for two adjustable alarm points. It also has one sensor fault for local connection and activation or deactivation of external devices like strobes, fans, auto dialers etc.

Features

• AutoCal® automatic calibration
• Smart sensor technology
• Digital display / control connection
• Internal push-button alarm settings