GfG Instruments, GfG

2811-4505-002 EC 28 Gas Transmitter with Sensor, Ammonia (NH3), 0-500 ppm, Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

3601-030 EC 36 Fixed Gas Transmitter, Oxygen (O2), Display / Alarm Relays by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment