GfG Instruments, GfG

2041001 GMA 41B Single Channel Controller, with Digital LED Display, External Reset Connection and Linear 4-20 mA Output by GfG

Gas Monitoring Controllers

The GMA 41 one-channel controller and the GMA 44 4-channel controller are an integral part of safe and reliable gas warning systems.

Alarm points

Every alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The point values can be freely adjusted within the detection range. They can also be adjusted later with the control keys to adapt to changing requirements. Every point value can be selected to be latching / non-latching or resettable / non-resettable.

Alarm relays

Every controller provides four voltage-free relays for the three alarms and the fault warning. The relays may be used to control external alarm devices like lights or horns. They can even introduce specific counter measures to prevent or limit dangers from gases or vapors.

Features

• Single or four channel controller
• Easy mounting on DIN-rail
• Multiple alarm points with relays

Additional features

The GMA 41 and GMA 44 store minimum or peak values, depending on the type of gas being detected. Even immediately following an alarm, gas dangers can be accurately detected.

The GMA (variant B) offers an integrated BUS-system. The BUS-system supplies power from one source to all connected GMAs. The BUS-system also connects individual controller alarms together so that, with the use of the key-operated switch, all connected monitors have one collective alarm. Several GMAs can be connected easily without additional wiring.

2044001 GMA 44B One to Four Channel Controller, with Digital LED Display and External Reset Connection (No Signal Output) by GfG

Gas Monitoring Controllers

The GMA 41 one-channel controller and the GMA 44 4-channel controller are an integral part of safe and reliable gas warning systems.

Alarm points

Every alarm can be adjusted separately. False alarms are eliminated with the adjustable alarm delay. The point values can be freely adjusted within the detection range. They can also be adjusted later with the control keys to adapt to changing requirements. Every point value can be selected to be latching / non-latching or resettable / non-resettable.

Alarm relays

Every controller provides four voltage-free relays for the three alarms and the fault warning. The relays may be used to control external alarm devices like lights or horns. They can even introduce specific counter measures to prevent or limit dangers from gases or vapors.

Features

• Single or four channel controller
• Easy mounting on DIN-rail
• Multiple alarm points with relays

Additional features

The GMA 41 and GMA 44 store minimum or peak values, depending on the type of gas being detected. Even immediately following an alarm, gas dangers can be accurately detected.

The GMA (variant B) offers an integrated BUS-system. The BUS-system supplies power from one source to all connected GMAs. The BUS-system also connects individual controller alarms together so that, with the use of the key-operated switch, all connected monitors have one collective alarm. Several GMAs can be connected easily without additional wiring.

Vent Line Adapter 2 NPT Fitting

2104-500 EC 21 Fixed Gas Transmitter with Internal Sensor, Carbon Monoxide (CO), 1 ppm, 0 - 500 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

GMA-SW - Key-operated Switch Module / Relay Alarm Card. Includes key switch to disable common alarms, 4 relays for Alarm 1, 2, fault and silence activated. Each alarm or fault relay activates when any of the respective alarms for any card on the same bus (motherboard) is active.

Note: This card requires a dedicated card slot (3HE x 7TE)

GMA BP. Cover Plate for non-used Card Slots (3HE x 21TE)

2109-100 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 100 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-1000 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 1000 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-1000F EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 2 ppm, 0 - 1000 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-100F EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 2 ppm, 0 - 100 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-200 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 200 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-200F EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 2 ppm, 0 - 200 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-250 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 250 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-250F EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 2 ppm, 0 - 250 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-500 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 500 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2109-500F EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 2 ppm, 0 - 500 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

2121011 GMA 101-R Single Channel Rack Mounted Controller Card Includes Features 4-20mA Output, Relays by GfG

Stationary gas monitoring systems

In many industrial operations, toxic or combustible gases and vapors or oxygen deficiency can be hazardous to personnel and disruptive to production. Even small amounts of some materials can cause dangerous situations. Both legal regulations and your responsibility to your workers demand continuous, responsive, and reliable monitoring for such dangerous gases. Only a fixed gas warning system like the GMA 100 II provides the security of a round-the-clock gas monitoring without the expense of manual measurement by your staff.

Control module GMA 100 II

The GMA 100 II stationary gas warning system is comprised of a control module and a remote sensor (MWG). The sensor continuously monitors the gas concentration and sends a signal via cable to the GMA 100 II control module for evaluation. The GMA 100 II constantly monitors its own operational status and powers the remote sensor.

Immediate recognition and warning of gas hazards

The GMA 100 II provides three alarm levels that can be used to initiate appropriate responses to gas hazards. The pre-alarm, for example, warns of low gas concentrations, indicating leaks, before dangerous situations occur. The other two main alarm thresholds indicate direct danger requiring immediate action. Alarm levels can be variably adjusted within the detection range and adapted to changing requirements. Every threshold can be set to latching / non-latching and resettable / non-resettable alarm points.

Quick reaction means increased safety

Every control module provides optional voltage-free relays for the three alarms and for fault warning. The relays may be used for controlling external alarm devices like beacons or buzzers, or they can activate specific counter measures (closing valves or turning on a fan) to eliminate the danger from gases or vapors. The GMA 100 II is flexible enough to accommodate your individual requirements. Every relay can be either a normally closed (NC) or normally open (NO) contact, and works in either closed or open circuit operation.

Easy Handling

A keypad controls the display of detection range, gas and units. Relays can be controlled and checked individually. No special tools or instruments are required. Alarm levels and calibration are set with push button menu control mechanical fine tuning with potentio meters is a thing of the past.

Single or collective alarm

The GMA RB relay module and the GMA SW key-operated switch allow you to group several control modules. The key-operated switch suppresses alarms during servicing.

In addition to the collective alarm, each controller can have up to four relays which can activate or deactivate electrical devices such as exhaust fans, valves, alarm horns or lights.

Protected against power failure

In case of a power failure, the optional battery back-up NAV takes over automatically and without delay to preserve safety. The NAV slides directly into the rack; no additional wiring is required.

More than 100 GfG sensors safety for all gas hazards

GfG Instrumentation s array of powerful and dependable remote sensors (MWG) provide a safe and reliable solution for individual detection tasks.

Combustible gases

Where combustible gases may build up to explosive concentrations, GfG Instrumentation offers a variety of monitoring techniques.

Toxic gases

Specially selected GfG sensors provide reliable monitoring of areas where toxic gases and vapors may be present.

Oxygen

Electrochemical sensors ensure reliable protection from hazards caused by oxygen deficiency or surplus.

GfG s remote sensors are available for more than 100 gases. Every remote sensor can be connected to the GMA 100 II. A simple calibration with a laptop rapidly configures the GMA 100 II to almost all requirements.

Monitoring four detection points simultaneously: GMA 100 / 4

The model GMA 100 / 4 has all the features of the GMA 100 II, and can operate four remote sensors simultaneously on one control module. This allows the configuration of a lowcost and space-saving gas monitoring system for multiple detection points.

Features

• Flexible, customizable, and economical
• Microprocessor controlled for all monitoring tasks
• Easy to operate

Includes

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

2121020 GMA 101-E Replacement Cards for MAK Style Racks (Older Versions) by GfG

Stationary gas monitoring systems

In many industrial operations, toxic or combustible gases and vapors or oxygen deficiency can be hazardous to personnel and disruptive to production. Even small amounts of some materials can cause dangerous situations. Both legal regulations and your responsibility to your workers demand continuous, responsive, and reliable monitoring for such dangerous gases. Only a fixed gas warning system like the GMA 100 II provides the security of a round-the-clock gas monitoring without the expense of manual measurement by your staff.

Control module GMA 100 II

The GMA 100 II stationary gas warning system is comprised of a control module and a remote sensor (MWG). The sensor continuously monitors the gas concentration and sends a signal via cable to the GMA 100 II control module for evaluation. The GMA 100 II constantly monitors its own operational status and powers the remote sensor.

Immediate recognition and warning of gas hazards

The GMA 100 II provides three alarm levels that can be used to initiate appropriate responses to gas hazards. The pre-alarm, for example, warns of low gas concentrations, indicating leaks, before dangerous situations occur. The other two main alarm thresholds indicate direct danger requiring immediate action. Alarm levels can be variably adjusted within the detection range and adapted to changing requirements. Every threshold can be set to latching / non-latching and resettable / non-resettable alarm points.

Quick reaction means increased safety

Every control module provides optional voltage-free relays for the three alarms and for fault warning. The relays may be used for controlling external alarm devices like beacons or buzzers, or they can activate specific counter measures (closing valves or turning on a fan) to eliminate the danger from gases or vapors. The GMA 100 II is flexible enough to accommodate your individual requirements. Every relay can be either a normally closed (NC) or normally open (NO) contact, and works in either closed or open circuit operation.

Easy Handling

A keypad controls the display of detection range, gas and units. Relays can be controlled and checked individually. No special tools or instruments are required. Alarm levels and calibration are set with push button menu control mechanical fine tuning with potentio meters is a thing of the past.

Single or collective alarm

The GMA RB relay module and the GMA SW key-operated switch allow you to group several control modules. The key-operated switch suppresses alarms during servicing.

In addition to the collective alarm, each controller can have up to four relays which can activate or deactivate electrical devices such as exhaust fans, valves, alarm horns or lights.

Protected against power failure

In case of a power failure, the optional battery back-up NAV takes over automatically and without delay to preserve safety. The NAV slides directly into the rack; no additional wiring is required.

More than 100 GfG sensors safety for all gas hazards

GfG Instrumentation s array of powerful and dependable remote sensors (MWG) provide a safe and reliable solution for individual detection tasks.

Combustible gases

Where combustible gases may build up to explosive concentrations, GfG Instrumentation offers a variety of monitoring techniques.

Toxic gases

Specially selected GfG sensors provide reliable monitoring of areas where toxic gases and vapors may be present.

Oxygen

Electrochemical sensors ensure reliable protection from hazards caused by oxygen deficiency or surplus.

GfG s remote sensors are available for more than 100 gases. Every remote sensor can be connected to the GMA 100 II. A simple calibration with a laptop rapidly configures the GMA 100 II to almost all requirements.

Monitoring four detection points simultaneously: GMA 100 / 4

The model GMA 100 / 4 has all the features of the GMA 100 II, and can operate four remote sensors simultaneously on one control module. This allows the configuration of a lowcost and space-saving gas monitoring system for multiple detection points.

Features

• Flexible, customizable, and economical
• Microprocessor controlled for all monitoring tasks
• Easy to operate

Includes

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

2122011 GMA 104-R Four Channel Rack Mounted Controller Card Includes Feature Relays by GfG

Stationary gas monitoring systems

In many industrial operations, toxic or combustible gases and vapors or oxygen deficiency can be hazardous to personnel and disruptive to production. Even small amounts of some materials can cause dangerous situations. Both legal regulations and your responsibility to your workers demand continuous, responsive, and reliable monitoring for such dangerous gases. Only a fixed gas warning system like the GMA 100 II provides the security of a round-the-clock gas monitoring without the expense of manual measurement by your staff.

Control module GMA 100 II

The GMA 100 II stationary gas warning system is comprised of a control module and a remote sensor (MWG). The sensor continuously monitors the gas concentration and sends a signal via cable to the GMA 100 II control module for evaluation. The GMA 100 II constantly monitors its own operational status and powers the remote sensor.

Immediate recognition and warning of gas hazards

The GMA 100 II provides three alarm levels that can be used to initiate appropriate responses to gas hazards. The pre-alarm, for example, warns of low gas concentrations, indicating leaks, before dangerous situations occur. The other two main alarm thresholds indicate direct danger requiring immediate action. Alarm levels can be variably adjusted within the detection range and adapted to changing requirements. Every threshold can be set to latching / non-latching and resettable / non-resettable alarm points.

Quick reaction means increased safety

Every control module provides optional voltage-free relays for the three alarms and for fault warning. The relays may be used for controlling external alarm devices like beacons or buzzers, or they can activate specific counter measures (closing valves or turning on a fan) to eliminate the danger from gases or vapors. The GMA 100 II is flexible enough to accommodate your individual requirements. Every relay can be either a normally closed (NC) or normally open (NO) contact, and works in either closed or open circuit operation.

Easy Handling

A keypad controls the display of detection range, gas and units. Relays can be controlled and checked individually. No special tools or instruments are required. Alarm levels and calibration are set with push button menu control mechanical fine tuning with potentio meters is a thing of the past.

Single or collective alarm

The GMA RB relay module and the GMA SW key-operated switch allow you to group several control modules. The key-operated switch suppresses alarms during servicing.

In addition to the collective alarm, each controller can have up to four relays which can activate or deactivate electrical devices such as exhaust fans, valves, alarm horns or lights.

Protected against power failure

In case of a power failure, the optional battery back-up NAV takes over automatically and without delay to preserve safety. The NAV slides directly into the rack; no additional wiring is required.

More than 100 GfG sensors safety for all gas hazards

GfG Instrumentation s array of powerful and dependable remote sensors (MWG) provide a safe and reliable solution for individual detection tasks.

Combustible gases

Where combustible gases may build up to explosive concentrations, GfG Instrumentation offers a variety of monitoring techniques.

Toxic gases

Specially selected GfG sensors provide reliable monitoring of areas where toxic gases and vapors may be present.

Oxygen

Electrochemical sensors ensure reliable protection from hazards caused by oxygen deficiency or surplus.

GfG s remote sensors are available for more than 100 gases. Every remote sensor can be connected to the GMA 100 II. A simple calibration with a laptop rapidly configures the GMA 100 II to almost all requirements.

Monitoring four detection points simultaneously: GMA 100 / 4

The model GMA 100 / 4 has all the features of the GMA 100 II, and can operate four remote sensors simultaneously on one control module. This allows the configuration of a lowcost and space-saving gas monitoring system for multiple detection points.

Features

• Flexible, customizable, and economical
• Microprocessor controlled for all monitoring tasks
• Easy to operate

Includes

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

2122011S1 GMA 104-R Four Channel Rack Mounted Controller Card Sets Includes Features Relays, Multiplexer by GfG

Stationary gas monitoring systems

In many industrial operations, toxic or combustible gases and vapors or oxygen deficiency can be hazardous to personnel and disruptive to production. Even small amounts of some materials can cause dangerous situations. Both legal regulations and your responsibility to your workers demand continuous, responsive, and reliable monitoring for such dangerous gases. Only a fixed gas warning system like the GMA 100 II provides the security of a round-the-clock gas monitoring without the expense of manual measurement by your staff.

Control module GMA 100 II

The GMA 100 II stationary gas warning system is comprised of a control module and a remote sensor (MWG). The sensor continuously monitors the gas concentration and sends a signal via cable to the GMA 100 II control module for evaluation. The GMA 100 II constantly monitors its own operational status and powers the remote sensor.

Immediate recognition and warning of gas hazards

The GMA 100 II provides three alarm levels that can be used to initiate appropriate responses to gas hazards. The pre-alarm, for example, warns of low gas concentrations, indicating leaks, before dangerous situations occur. The other two main alarm thresholds indicate direct danger requiring immediate action. Alarm levels can be variably adjusted within the detection range and adapted to changing requirements. Every threshold can be set to latching / non-latching and resettable / non-resettable alarm points.

Quick reaction means increased safety

Every control module provides optional voltage-free relays for the three alarms and for fault warning. The relays may be used for controlling external alarm devices like beacons or buzzers, or they can activate specific counter measures (closing valves or turning on a fan) to eliminate the danger from gases or vapors. The GMA 100 II is flexible enough to accommodate your individual requirements. Every relay can be either a normally closed (NC) or normally open (NO) contact, and works in either closed or open circuit operation.

Easy Handling

A keypad controls the display of detection range, gas and units. Relays can be controlled and checked individually. No special tools or instruments are required. Alarm levels and calibration are set with push button menu control mechanical fine tuning with potentio meters is a thing of the past.

Single or collective alarm

The GMA RB relay module and the GMA SW key-operated switch allow you to group several control modules. The key-operated switch suppresses alarms during servicing.

In addition to the collective alarm, each controller can have up to four relays which can activate or deactivate electrical devices such as exhaust fans, valves, alarm horns or lights.

Protected against power failure

In case of a power failure, the optional battery back-up NAV takes over automatically and without delay to preserve safety. The NAV slides directly into the rack; no additional wiring is required.

More than 100 GfG sensors safety for all gas hazards

GfG Instrumentation s array of powerful and dependable remote sensors (MWG) provide a safe and reliable solution for individual detection tasks.

Combustible gases

Where combustible gases may build up to explosive concentrations, GfG Instrumentation offers a variety of monitoring techniques.

Toxic gases

Specially selected GfG sensors provide reliable monitoring of areas where toxic gases and vapors may be present.

Oxygen

Electrochemical sensors ensure reliable protection from hazards caused by oxygen deficiency or surplus.

GfG s remote sensors are available for more than 100 gases. Every remote sensor can be connected to the GMA 100 II. A simple calibration with a laptop rapidly configures the GMA 100 II to almost all requirements.

Monitoring four detection points simultaneously: GMA 100 / 4

The model GMA 100 / 4 has all the features of the GMA 100 II, and can operate four remote sensors simultaneously on one control module. This allows the configuration of a lowcost and space-saving gas monitoring system for multiple detection points.

Features

• Flexible, customizable, and economical
• Microprocessor controlled for all monitoring tasks
• Easy to operate

Includes

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

2122011S2 GMA 104-R Four Channel Rack Mounted Controller Card Sets Includes Features Relays, Multiplexer, Power Supply by GfG

Stationary gas monitoring systems

In many industrial operations, toxic or combustible gases and vapors or oxygen deficiency can be hazardous to personnel and disruptive to production. Even small amounts of some materials can cause dangerous situations. Both legal regulations and your responsibility to your workers demand continuous, responsive, and reliable monitoring for such dangerous gases. Only a fixed gas warning system like the GMA 100 II provides the security of a round-the-clock gas monitoring without the expense of manual measurement by your staff.

Control module GMA 100 II

The GMA 100 II stationary gas warning system is comprised of a control module and a remote sensor (MWG). The sensor continuously monitors the gas concentration and sends a signal via cable to the GMA 100 II control module for evaluation. The GMA 100 II constantly monitors its own operational status and powers the remote sensor.

Immediate recognition and warning of gas hazards

The GMA 100 II provides three alarm levels that can be used to initiate appropriate responses to gas hazards. The pre-alarm, for example, warns of low gas concentrations, indicating leaks, before dangerous situations occur. The other two main alarm thresholds indicate direct danger requiring immediate action. Alarm levels can be variably adjusted within the detection range and adapted to changing requirements. Every threshold can be set to latching / non-latching and resettable / non-resettable alarm points.

Quick reaction means increased safety

Every control module provides optional voltage-free relays for the three alarms and for fault warning. The relays may be used for controlling external alarm devices like beacons or buzzers, or they can activate specific counter measures (closing valves or turning on a fan) to eliminate the danger from gases or vapors. The GMA 100 II is flexible enough to accommodate your individual requirements. Every relay can be either a normally closed (NC) or normally open (NO) contact, and works in either closed or open circuit operation.

Easy Handling

A keypad controls the display of detection range, gas and units. Relays can be controlled and checked individually. No special tools or instruments are required. Alarm levels and calibration are set with push button menu control mechanical fine tuning with potentio meters is a thing of the past.

Single or collective alarm

The GMA RB relay module and the GMA SW key-operated switch allow you to group several control modules. The key-operated switch suppresses alarms during servicing.

In addition to the collective alarm, each controller can have up to four relays which can activate or deactivate electrical devices such as exhaust fans, valves, alarm horns or lights.

Protected against power failure

In case of a power failure, the optional battery back-up NAV takes over automatically and without delay to preserve safety. The NAV slides directly into the rack; no additional wiring is required.

More than 100 GfG sensors safety for all gas hazards

GfG Instrumentation s array of powerful and dependable remote sensors (MWG) provide a safe and reliable solution for individual detection tasks.

Combustible gases

Where combustible gases may build up to explosive concentrations, GfG Instrumentation offers a variety of monitoring techniques.

Toxic gases

Specially selected GfG sensors provide reliable monitoring of areas where toxic gases and vapors may be present.

Oxygen

Electrochemical sensors ensure reliable protection from hazards caused by oxygen deficiency or surplus.

GfG s remote sensors are available for more than 100 gases. Every remote sensor can be connected to the GMA 100 II. A simple calibration with a laptop rapidly configures the GMA 100 II to almost all requirements.

Monitoring four detection points simultaneously: GMA 100 / 4

The model GMA 100 / 4 has all the features of the GMA 100 II, and can operate four remote sensors simultaneously on one control module. This allows the configuration of a lowcost and space-saving gas monitoring system for multiple detection points.

Features

• Flexible, customizable, and economical
• Microprocessor controlled for all monitoring tasks
• Easy to operate

Includes

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

GMA-RB Common Alarm Module. Includes 4 relays for Alarm 1, 2, 3 and fault. Each alarm relay activates when any of the respective alarms for any card on the same bus (motherboard) is active.

Note: This module requires two adjacent slots that do not host any 4-channel controllers and one of which must be populated with any other style card.

GMA - SPG. Rack Mount Power Supply.

Note: This item requires 1 card slot (3HE x 21TE).

GMA R2 Rack Mounted Enclosure (3HE x 14TE)