$750 - $1000, Fixed System Gas Monitors

CS 21 Transmitter Low Cost Solid State Sensor

CS 21 with External Sensor

Transmitter for monitoring toxic gases and combustibles

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants Long sensor life
• Fast response

2238002 CC 0238 Fixed Gas Transmitter, 0 - 100% LEL, 0.2 - 1 mA Output by GfG

Protection from combustible gases

Detection principle

To ensure stable measurement signals, all GfG remote sensors have integrated electronic circuits for voltage stabilization, signal transmission, and temperature compensation.

Remote sensor

Features

• Simple calibration and setup
• Poison resistant sensors
• Ex-proof housings

2303-100 EC 23 Fixed Gas Transmitter, Hydrogen Sulfide (H2S), 0 to 100 ppm by GfG

GfG's EC 23 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Robust housing

The robust aluminum casing protects the transmitter's electronic components from the harshest environments. The corrosion resistant casing protects the electricalcomponents from atmospheric hazards and is dust-tight.

Simple gas detection

The EC 23 is the simplest way to monitor ambient conditions. Simply attach the EC 23 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in air. The EC 23 is also reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector has a "quick disconnect" feature to simplify transmitter installation and service.

• Simple to use and extremely economical
• Robust aluminum housing is corrosion resistant and dust-tight
• Many sensors available, including 3 detection ranges for ammonia (NH3)
• Linear 4 to 20 mA output signal
• 18 24 VDC

2303-500 EC 23 Fixed Gas Transmitter, Hydrogen Sulfide (H2S), 0 to 500 ppm by GfG

GfG's EC 23 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Robust housing

The robust aluminum casing protects the transmitter's electronic components from the harshest environments. The corrosion resistant casing protects the electricalcomponents from atmospheric hazards and is dust-tight.

Simple gas detection

The EC 23 is the simplest way to monitor ambient conditions. Simply attach the EC 23 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in air. The EC 23 is also reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector has a "quick disconnect" feature to simplify transmitter installation and service.

• Simple to use and extremely economical
• Robust aluminum housing is corrosion resistant and dust-tight
• Many sensors available, including 3 detection ranges for ammonia (NH3)
• Linear 4 to 20 mA output signal
• 18 24 VDC

2304-500 EC 23 Fixed Gas Transmitter, Carbon Monoxide (CO), 0 to 500 ppm by GfG

GfG's EC 23 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Robust housing

The robust aluminum casing protects the transmitter's electronic components from the harshest environments. The corrosion resistant casing protects the electricalcomponents from atmospheric hazards and is dust-tight.

Simple gas detection

The EC 23 is the simplest way to monitor ambient conditions. Simply attach the EC 23 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in air. The EC 23 is also reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector has a "quick disconnect" feature to simplify transmitter installation and service.

• Simple to use and extremely economical
• Robust aluminum housing is corrosion resistant and dust-tight
• Many sensors available, including 3 detection ranges for ammonia (NH3)
• Linear 4 to 20 mA output signal
• 18 24 VDC

2801-00-002 CC 28 Fixed Gas Transmitter, Base Unit (no sensor), Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG's new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don't worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-00-003 CC 28 Fixed Gas Transmitter, Base Unit (no sensor), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG's new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don't worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2811-000-001 EC 28 Gas Transmitter with Sensor, with Sensor, No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

61-0190RK-HC Sensor, IR, Hydrocarbon (HC) 0 - 100% LEL, Isobutane Standard Calibration, Explosion Proof Direct Connection (No Transmitter, No J-Box), cULus Version by RKI Instruments

When working on potentially hazardous jobsites, safety managers should look for workplace safety solutions that are dependable and steadfast. When lives are on the line, a workplace cannot afford subpar safety products. That is why, at RKI Instruments, workplace safety is a top priority. Their Research and Development team work daily to integrate the latest technology with the best industry practices. With a reputation for excellent products, RKI Instruments introduces the latest in direct connect sensor technology. Designed for use in Class 1, Division 2 hazardous environments, the Direct Connect Sensors are designed specifically for RKI Beacon 110, 200, and 410 controllers.

Direct Connect Sensors

The RKI Direct Connect Sensors series gas sensors are state of the art gas detection sensors available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and a variety of toxic gases. To use the Direct Connect Sensors, they can be used for remote detection by mounting them onto explosion proof junction boxes, or they can mount directly onto controllers and be used as a completely standalone system. Their unique plugin design allows for a quick and easy tool free installation on jobsites.

Detection solutions for a variety of hazardous environments

The Direct Connect Sensors are designed to be use in both indoor and outdoor settings. Additionally, some of the sensors are available in explosion proof models. The explosion proof models utilize a patented coating which serves double duty as also being water repellant. Users can also purchase splash guards to protect the sensors from very wet conditions.

Sensor Technology

Each sensor is crafted with stainless steel and housed in cast aluminum (stainless steel housing is available for some sensors). The Direct Connect Sensors are available in 2 forms: explosion proof and non-explosion proof. The explosion proof sensors are available as catalytic sensors for LEL, and LEL H2 specific. For hydrogen sulfide and carbon monoxide, the sensors utilize electrochemical technology which provides incredibly specific accuracy and quick response. Oxygen sensors work with galvanic technology, and infrared sensors for methane, hydrocarbons, and carbon dioxide. Non-explosion proof uses a galvanic sensor for oxygen; electrochemical sensors for hydrogen sulfide, carbon monoxide and other toxic gases; and infrared for carbon dioxide. Both explosion proof and non-explosion proof have 1 year warranties for materials and craftsmanship.

Specifications

The response times are under 30 seconds for all gases except hydrogen sulfide and carbon monoxide in the non-explosion versions (with a response time of 35 seconds) and non-explosion proof model sensor for toxic gases which has a 60 second response time. The life expectancy of all sensors are between 2 and 5 years.

The Direct Connect Sensors are compatible with several RKI Industries' accessories including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors, and dataloggers.

*Please note we can only ship RKI products to customers within the United States

61-0191RK-03 Sensor, IR, Carbon Dioxide (CO2) 0 - 5,000 ppm, Explosion Proof Direct Connection (No Transmitter, No J-Box), cULus Version by RKI Instruments

When working on potentially hazardous jobsites, safety managers should look for workplace safety solutions that are dependable and steadfast. When lives are on the line, a workplace cannot afford subpar safety products. That is why, at RKI Instruments, workplace safety is a top priority. Their Research and Development team work daily to integrate the latest technology with the best industry practices. With a reputation for excellent products, RKI Instruments introduces the latest in direct connect sensor technology. Designed for use in Class 1, Division 2 hazardous environments, the Direct Connect Sensors are designed specifically for RKI Beacon 110, 200, and 410 controllers.

Direct Connect Sensors

The RKI Direct Connect Sensors series gas sensors are state of the art gas detection sensors available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and a variety of toxic gases. To use the Direct Connect Sensors, they can be used for remote detection by mounting them onto explosion proof junction boxes, or they can mount directly onto controllers and be used as a completely standalone system. Their unique plugin design allows for a quick and easy tool free installation on jobsites.

Detection solutions for a variety of hazardous environments

The Direct Connect Sensors are designed to be use in both indoor and outdoor settings. Additionally, some of the sensors are available in explosion proof models. The explosion proof models utilize a patented coating which serves double duty as also being water repellant. Users can also purchase splash guards to protect the sensors from very wet conditions.

Sensor Technology

Each sensor is crafted with stainless steel and housed in cast aluminum (stainless steel housing is available for some sensors). The Direct Connect Sensors are available in 2 forms: explosion proof and non-explosion proof. The explosion proof sensors are available as catalytic sensors for LEL, and LEL H2 specific. For hydrogen sulfide and carbon monoxide, the sensors utilize electrochemical technology which provides incredibly specific accuracy and quick response. Oxygen sensors work with galvanic technology, and infrared sensors for methane, hydrocarbons, and carbon dioxide. Non-explosion proof uses a galvanic sensor for oxygen; electrochemical sensors for hydrogen sulfide, carbon monoxide and other toxic gases; and infrared for carbon dioxide. Both explosion proof and non-explosion proof have 1 year warranties for materials and craftsmanship.

Specifications

The response times are under 30 seconds for all gases except hydrogen sulfide and carbon monoxide in the non-explosion versions (with a response time of 35 seconds) and non-explosion proof model sensor for toxic gases which has a 60 second response time. The life expectancy of all sensors are between 2 and 5 years.

The Direct Connect Sensors are compatible with several RKI Industries' accessories including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors, and dataloggers.

*Please note we can only ship RKI products to customers within the United States

61-0191RK-05 Sensor, IR, Carbon Dioxide (CO2) 0 - 50%, Explosion Proof Direct Connection (No Transmitter, No J-Box), cULus Version by RKI Instruments

When working on potentially hazardous jobsites, safety managers should look for workplace safety solutions that are dependable and steadfast. When lives are on the line, a workplace cannot afford subpar safety products. That is why, at RKI Instruments, workplace safety is a top priority. Their Research and Development team work daily to integrate the latest technology with the best industry practices. With a reputation for excellent products, RKI Instruments introduces the latest in direct connect sensor technology. Designed for use in Class 1, Division 2 hazardous environments, the Direct Connect Sensors are designed specifically for RKI Beacon 110, 200, and 410 controllers.

Direct Connect Sensors

The RKI Direct Connect Sensors series gas sensors are state of the art gas detection sensors available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and a variety of toxic gases. To use the Direct Connect Sensors, they can be used for remote detection by mounting them onto explosion proof junction boxes, or they can mount directly onto controllers and be used as a completely standalone system. Their unique plugin design allows for a quick and easy tool free installation on jobsites.

Detection solutions for a variety of hazardous environments

The Direct Connect Sensors are designed to be use in both indoor and outdoor settings. Additionally, some of the sensors are available in explosion proof models. The explosion proof models utilize a patented coating which serves double duty as also being water repellant. Users can also purchase splash guards to protect the sensors from very wet conditions.

Sensor Technology

Each sensor is crafted with stainless steel and housed in cast aluminum (stainless steel housing is available for some sensors). The Direct Connect Sensors are available in 2 forms: explosion proof and non-explosion proof. The explosion proof sensors are available as catalytic sensors for LEL, and LEL H2 specific. For hydrogen sulfide and carbon monoxide, the sensors utilize electrochemical technology which provides incredibly specific accuracy and quick response. Oxygen sensors work with galvanic technology, and infrared sensors for methane, hydrocarbons, and carbon dioxide. Non-explosion proof uses a galvanic sensor for oxygen; electrochemical sensors for hydrogen sulfide, carbon monoxide and other toxic gases; and infrared for carbon dioxide. Both explosion proof and non-explosion proof have 1 year warranties for materials and craftsmanship.

Specifications

The response times are under 30 seconds for all gases except hydrogen sulfide and carbon monoxide in the non-explosion versions (with a response time of 35 seconds) and non-explosion proof model sensor for toxic gases which has a 60 second response time. The life expectancy of all sensors are between 2 and 5 years.

The Direct Connect Sensors are compatible with several RKI Industries' accessories including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors, and dataloggers.

*Please note we can only ship RKI products to customers within the United States

61-0192RK-CH4 Sensor, IR, Methane (CH4) 0 - 100% Volume, Explosion Proof Direct Connection (No Transmitter, No J-Box), cULus Version by RKI Instruments

When working on potentially hazardous jobsites, safety managers should look for workplace safety solutions that are dependable and steadfast. When lives are on the line, a workplace cannot afford subpar safety products. That is why, at RKI Instruments, workplace safety is a top priority. Their Research and Development team work daily to integrate the latest technology with the best industry practices. With a reputation for excellent products, RKI Instruments introduces the latest in direct connect sensor technology. Designed for use in Class 1, Division 2 hazardous environments, the Direct Connect Sensors are designed specifically for RKI Beacon 110, 200, and 410 controllers.

Direct Connect Sensors

The RKI Direct Connect Sensors series gas sensors are state of the art gas detection sensors available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and a variety of toxic gases. To use the Direct Connect Sensors, they can be used for remote detection by mounting them onto explosion proof junction boxes, or they can mount directly onto controllers and be used as a completely standalone system. Their unique plugin design allows for a quick and easy tool free installation on jobsites.

Detection solutions for a variety of hazardous environments

The Direct Connect Sensors are designed to be use in both indoor and outdoor settings. Additionally, some of the sensors are available in explosion proof models. The explosion proof models utilize a patented coating which serves double duty as also being water repellant. Users can also purchase splash guards to protect the sensors from very wet conditions.

Sensor Technology

Each sensor is crafted with stainless steel and housed in cast aluminum (stainless steel housing is available for some sensors). The Direct Connect Sensors are available in 2 forms: explosion proof and non-explosion proof. The explosion proof sensors are available as catalytic sensors for LEL, and LEL H2 specific. For hydrogen sulfide and carbon monoxide, the sensors utilize electrochemical technology which provides incredibly specific accuracy and quick response. Oxygen sensors work with galvanic technology, and infrared sensors for methane, hydrocarbons, and carbon dioxide. Non-explosion proof uses a galvanic sensor for oxygen; electrochemical sensors for hydrogen sulfide, carbon monoxide and other toxic gases; and infrared for carbon dioxide. Both explosion proof and non-explosion proof have 1 year warranties for materials and craftsmanship.

Specifications

The response times are under 30 seconds for all gases except hydrogen sulfide and carbon monoxide in the non-explosion versions (with a response time of 35 seconds) and non-explosion proof model sensor for toxic gases which has a 60 second response time. The life expectancy of all sensors are between 2 and 5 years.

The Direct Connect Sensors are compatible with several RKI Industries' accessories including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors, and dataloggers.

*Please note we can only ship RKI products to customers within the United States

61-0207-02 Sensor, IR Carbon Dioxide (CO2) 0-5000 ppm, Explosion Proof Direct Connection, 3 / 4 inch NPT Conduit Mounting by RKI Instruments

When working on potentially hazardous jobsites, safety managers should look for workplace safety solutions that are dependable and steadfast. When lives are on the line, a workplace cannot afford subpar safety products. That is why, at RKI Instruments, workplace safety is a top priority. Their Research and Development team work daily to integrate the latest technology with the best industry practices. With a reputation for excellent products, RKI Instruments introduces the latest in direct connect sensor technology. Designed for use in Class 1, Division 2 hazardous environments, the Direct Connect Sensors are designed specifically for RKI Beacon 110, 200, and 410 controllers.

Direct Connect Sensors

The RKI Direct Connect Sensors series gas sensors are state of the art gas detection sensors available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and a variety of toxic gases. To use the Direct Connect Sensors, they can be used for remote detection by mounting them onto explosion proof junction boxes, or they can mount directly onto controllers and be used as a completely standalone system. Their unique plugin design allows for a quick and easy tool free installation on jobsites.

Detection solutions for a variety of hazardous environments

The Direct Connect Sensors are designed to be use in both indoor and outdoor settings. Additionally, some of the sensors are available in explosion proof models. The explosion proof models utilize a patented coating which serves double duty as also being water repellant. Users can also purchase splash guards to protect the sensors from very wet conditions.

Sensor Technology

Each sensor is crafted with stainless steel and housed in cast aluminum (stainless steel housing is available for some sensors). The Direct Connect Sensors are available in 2 forms: explosion proof and non-explosion proof. The explosion proof sensors are available as catalytic sensors for LEL, and LEL H2 specific. For hydrogen sulfide and carbon monoxide, the sensors utilize electrochemical technology which provides incredibly specific accuracy and quick response. Oxygen sensors work with galvanic technology, and infrared sensors for methane, hydrocarbons, and carbon dioxide. Non-explosion proof uses a galvanic sensor for oxygen; electrochemical sensors for hydrogen sulfide, carbon monoxide and other toxic gases; and infrared for carbon dioxide. Both explosion proof and non-explosion proof have 1 year warranties for materials and craftsmanship.

Specifications

The response times are under 30 seconds for all gases except hydrogen sulfide and carbon monoxide in the non-explosion versions (with a response time of 35 seconds) and non-explosion proof model sensor for toxic gases which has a 60 second response time. The life expectancy of all sensors are between 2 and 5 years.

The Direct Connect Sensors are compatible with several RKI Industries' accessories including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors, and dataloggers.

*Please note we can only ship RKI products to customers within the United States