All Products

SCT-108.001.04 SCT-CON-PEN-2 Handheld Conductivity Meter with High Resolution by ScichemTech

Includes:

• Handheld Conductivity Meter
• Standard Solution
• Battery
• Screw-Driver
• Instruction Manual

Features:

• Reliable SCT Tester for basic easy Conductivity measurement.
• Ergonomic Design - Waterproof IP57 rated.
• Accurate & Fast in measurements 1 μS/CM resolution.
• Removable & changeable electrode.
• Large and clear display
• Manual calibration through screw trim port 1 or 2 points.
• With better Conductivity resolution 1 μS/CM.
• With Automatic Temperature Compensation (ATC).
• Battery operated.

5601-3051 GDX-350 Gas Sensor Transmitter/Monitor, [NH3] 0-500 ppm, 2-wire by Bacharach

Bacharach's new state-of-the-art GDX-350 transmitters, with Smart Sensor technology, provide accurate and continuous detection of toxic, combustible and asphyxiate gases. The full-featured design of the GDX-350 includes a large LCD display, a 4-20 mA interface, programmable alarms, optional relays and a Modbus interface. Exclusive pre-calibrated replacement sensor technology makes occasional maintenance practically effortless. Rugged construction, intrinsic safety capability (in two-wire mode with barrier) and an explosion-proof housing allow the GDX-350 to operate directly in hazardous-rated areas of many industrial environments, delivering reliable, superior-sensing performance to protect human life, equipment and property.

With its large LCD display, the GDX-350 shows gas concentrations, engineering units and bar graphs along with the most recent 30 minutes of trend data. Utilizing the on-board magnetic keypad, users can also navigate through the display to change alarm set points, instrument configurations, or enter into maintenance mode for non-intrusive sensor calibration. For security, menu options also enable the selection of an authorization code to lock critical parameters. Accompanying the LCD display are standard LED alarm indicators that show when low and high alarm conditions are met. An optional relay board is available to provide three 5-amp relays that can be used to drive audible/visual alarms, or activate exhaust fans.

Features & Benefits:

• Pre-calibrated Smart Sensor capability with 'plug-n-play' convenience minimizes maintenance and downtime
• Non-Dispersive Infrared (NDIR), Catalytic Bead and Electrochemical sensor options available
• Can be placed directly in hazardous environments where leaks occur for quick detection and rapid response
• Graphic LCD for real-time monitoring of concentrations
• 4-20 mA, optional Modbus RTU® and wireless interface
• Easily update alarm set points, configurations or maintenance modes using the LCD display
• 30-minute onboard data trend

HA40PY-H 4 Channel Controller by Honeywell Analytics

Honeywell Analytics offers a family of gas detection controllers that monitor 2, 4, 8 or 16 points of gas detection. Our controller family delivers robust safety while being cost effective.

The Honeywell digital gas controllers are designed to work in the harshest industrial or commercial environments. A NEMA4x and explosion proof enclosure allows you to place the controllers in all hazardous locations to monitor for toxic gases, combustible gases, and oxygen deficiency.

The controllers are easy to install and feature large graphical LCD display, standard 4-20mA inputs, and non-intrusive inputs for hazardous areas. An optional RS-485 Modbus slave port allows up to 128 HA 40 s to be multi-dropped onto a single data highway for interrogation by another Modbus master. A 10-BaseT Ethernet cable is also available for utilizing the popular Modbus TCP/IP protocol.

The HA-20 and HA-40 controllers are designed to provide simultaneous display and alarm functions for two or four 4-20mA sensor transmitters. The 4-20mA inputs are standard equipped and ideal for interfacing to sensor transmitters that may be long distances from the controller.

The Honeywell Analytics HA-71 16 Channel Gas Detection Controller is designed to provide simultaneous display and alarm functions for up to 16 input variables.

Part Number: 66L-98-50

*Please note we can only ship RKI products to customers within the United States

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

72-5469RK Eagle Portable Monitor for O2/CO/H2S/NH3 by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

G460-11-03-24-00-24 G460 Multi-Gas Detector with Alkaline Smart Pump and NiMH Battery, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, NO2 by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

722-004 Eagle 2 Portable Monitor for O2/CO by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

724-052 Eagle 2 Portable Monitor for LEL & PPM/O2/CO/HCN by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

Part Number: 34L-SIH4-10

341KC1 Single Input K-Type Thermocouple Thermometer with GK11M Probe by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Auto Field Calibrate in less than 10 seconds in ice water to achieve ± 1°F system (tester & probe) accuracy within 30°F to 120°F temperature range
• Min / Max Record
• Auto Resolution (0.1° / 1°)
• °C/°F Selectable
• Hold feature freezes reading on display
• Auto Off
• Protective rubber boot
• Easy to read LCD display

Includes:

• GK11M temperature probe
• A304 protective boot
• A255 soft pouch

73-0611RK RX-516 Multigas IR Monitor, 0 - 100% LEL/0 - 100% Vol HC/0 - 25% O2/0 - 100 PPM H2S by RKI Instruments

The Crude Oil Tanker model is a combination type portable HC, O2, and H2s gas detector with an Infrared (NDIR) type sensor, galvanic cell type sensor and Electro-chemical cell type sensor. These sensors provide accurate detection of HC, O2 and H2S levels even in N2 and other inert environments. The measuring ranges of model RX-516 are 0-100%LEL / 0-10%vol for HC, 0-25% vol for O2 and 0-100.0ppm for H2S respectively. A higher range for H2S (0-1,000ppm) is available in model RX-517. A manual switch is used to change the flow to a unique path for high H2S applications to protect the other sensors. The RX-516 / RX-517 has an explosion proof and Intrinsically Safe design so that it can be used safely in any envrionment.

Features

• Dual range detection of CH4 or HC in %vol and %LEL.
• Unique gas combinations include: CH4/O2/CO/CO2/HC/O2/H2S
• Accurately measure CH4 or HC from inerted tanks with infrared sensor.
• High range H2S 0-1,000ppm available (RX-517).
• Intrinsically safe design.
• Datalogging (Max 30 hours of interval trend).

Application

• Crude oil tanker storage tank gas monitoring

*Please note we can only ship RKI products to customers within the United States

72-5316RK-02 Eagle Portable Monitor for LEL/O2/CO2 (10,000 ppm) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

XT-X0H0-B-OE GasAlertMax XT II 2 Gas Detector, Oxygen (O2), Hydrogen Sulfide (H2S) - Black Housing, OE Version (Other Regions, 2-pin UK plug) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XTX0H0BOE

XT-X0HM-Y-BR GasAlertMax XT II 3 Gas Detector, Oxygen (O2), Hydrogen Sulfide (H2S), Carbon Monoxide (CO) - Yellow Housing, BR Version (Brazil) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XTX0HMYBR

6500-2015 MGS-350 Gas Detector, O3 (Ozone) 0-2 ppm IP66 Housing by Bacharach

Bacharach's MGS-350 Series Gas Transmitter is a feature-rich gas detection system with a wide range of sensor options to provide real-time monitoring of refrigerant, combustible, TVOC and toxic gases. It comes standard with analog and digital outputs including 4-20 mA, 0-5V, 0-10V and Serial Data, allowing them to connect directly to most BMS, SCADA or control systems. An onboard visual LED alarm indicator alerts area personnel when levels have exceeded the desired limit. The MGS-350 also features alarm relays (high and low) for connection to external audible/visual alarms or a BMS or BAS system.

MGS-350 Gas Transmitters, combined with the MGS Controller, can provide facility owners with a customized and complete low-cost gas-detection system. A variety of housing options are available (shown below), from standard to water resistant enclosures, which allow the MGS-350 units to be placed in many environments.

Features & Benefits:

• Detects refrigerants (CFCs, HFCs, HCFCs), TVOCs, combustible gases/hydrocarbons, O2, NH3, CO, H2S, H2, NO, NO2, SO2, Cl2, and O3
• Long-lasting infrared, semiconductor, catalytic bead and electrochemical sensor options for effective leak detection - at the most affordable cost.
• Precalibrated replacement sensors for easy maintenance
• Integrated visual LED alarm
• Two onboard alarm relays (low and high)
• Multiple housing options available, including IP 66 and duct mount, for placement in diverse environments.
• Analog outputs: 4-20 mA, 0-5V, 0-10V, featuring 12/24 VAC / 12-30VDC operation

722-073 Eagle 2 Portable Monitor for CH4 (100% LEL/100 % Volume (IR) Autoranging)/H2S (0 - 100 ppm) by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

65-2405RK-05 S2 Series LEL Sensor (Catalytic)/Transmitter with Explosion Proof J-Box, CSA Version, (Specify Calibration) by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States