All Products

2214033 CS 21 Fixed Gas Transmitter, Dichloromethane (CH₂CL₂), 0(30) - 300 ppm by GfG

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants
• Long sensor life
• Fast response

XSB2F2-B2-H Advantage MegaTron XS Boiler Controller, Dual Boiler, 2 Feed Timers, Non Temp Comp Probe with Internet - CAT5 and Wifi by Quantrol

Features

• Cycles control with the make-up conductivity
• Display mA readings in the System RUN screen
• Auxiliary flowmeter inputs can activate a pulse timer
• ORP has two set points with the second linked to a 28-day timer for shocking to a higher ORP value
• USB downloaded history can be uploaded to WebAdvantage
• Web communications to WebAdvantage via the customer's internal network or external cell router and data service
• Four or eight mA inputs are available for specialty sensors, including PTSA trace, pressure, drum level, free chlorine and many other sensors
• Force a relay into a single event defined time to catch up on chemical feed
• Supports Bacnet, Modbus or Lonworks building management communications
• Receive alarm from an auxiliary flowmeter if bleed is not occurring correctly
• Biocide timers can remember to feed one event when flow comes back on if one or more feed events are missed during no flow conditions
• Second conductivity set point for no inhibitor conditions is available
• Tower conductivity, make-up conductivity, pH and ORP in one unit
• Pulse timers can have two different water meter inputs added together for the accumulate activation setting
• Chemical feed can be interrupted during bleed or other events
• Five miscellaneous digital inputs from drum level wands
• Advanced relay logic for special controlling schemes
• Pulse timer initiated boiler conductivity sampling
• Single or dual boiler conductivity control

Part Number: J10351VM1

ECFX-250-AS Manning EC-FX Gas Detector, NH3 0/250ppm ATMOS Stainless Steel Enclosure by Honeywell Analytics

If you use ammonia as part of your refrigeration process, you face several challenges in protecting your plant from the danger and expense of ammonia leaks within cold storage, refrigerated process areas and the engine rooms. Introducing a better, tougher, longer-lasting sensor to cover your needs. The EC-FX-NH3 maintains sensitivity and accuracy — even with rapid changes in temperature and humidity.

Now one tough sensor can work in three harsh environments. With the stability you can count and low cost you want, the EC-FX-NH3 is the new gold standard in ammonia detection.

Features & Benefits

• Responds quickly to ammonia concentrations in low parts per million (PPM)
• Rugged construction for long-term reliability
• ATMOSTM Technology for environmental flexibility

Quick Specs

• Stainless steel enclosure with LCD options
• All-new ammonia sensor with a proprietary electrolyte
• 3-year warranty—twice the warranty of most sensors

ECFX-1000-ALS Manning EC-FX Gas Detector, NH3 0/1000 ppm, ATMOS, LCD, Stainless Steel Enclosure by Honeywell Analytics

If you use ammonia as part of your refrigeration process, you face several challenges in protecting your plant from the danger and expense of ammonia leaks within cold storage, refrigerated process areas and the engine rooms. Introducing a better, tougher, longer-lasting sensor to cover your needs. The EC-FX-NH3 maintains sensitivity and accuracy — even with rapid changes in temperature and humidity.

Now one tough sensor can work in three harsh environments. With the stability you can count and low cost you want, the EC-FX-NH3 is the new gold standard in ammonia detection.

Features & Benefits

• Responds quickly to ammonia concentrations in low parts per million (PPM)
• Rugged construction for long-term reliability
• ATMOSTM Technology for environmental flexibility

Quick Specs

• Stainless steel enclosure with LCD options
• All-new ammonia sensor with a proprietary electrolyte
• 3-year warranty—twice the warranty of most sensors

46100 Complete MINI Duct Rodder with Frame and Spool, 100' by Pelsue

Developed for 1" or 2" (2.5 or 5 cm) conduit and up to 400 feet (122 m). The Mini rodder combines lightweight and portability along with high rod strength. Pulling strength is rated at 2200 lbs (998 kg) while 12" to 18" (30 to 45 cm) radius bends are easily negotiated. Especially effective for placement of wire or cable in interior building conduit. This counter wound rod from Germany is capable of tight bend radii without breaking. See story on pg. 24* Complete unit includes: 1/4" (.63 cm) diameter rod from 100' to 400' (30.5 m to 122m) lengths, Vertical stand and spool with spool brakes to avoid "spring out" effect, and threaded end fittings to accept all accessories.

MKLP30-5B Low Pressure Mist Kit for 30" Fans; 5 x 0.012" Nozzles, Black by Schaefer

Instantly convert your circulation fan into a misting fan with Schaefer low pressure misting kits. The misting kits can reduce air temperature up to 30°F with wind from a fan and standard water pressure from an ordinary garden hose. The kits are easy to use with push releasable connections and optional ball valve water shut offs. Available for fans of all sizes, Schaefer mist kits provide an easy economical solution for your evaporative cooling needs.

Features and Benefits:

• 1/4" black polyethylene tubing for durability and resistance to cracking
• Brass and stainless steel nozzles to atomize the water
• Push releasable nozzles and fittings for easy cleaning
• Optional ball valve for quick and easy shutoff of water supply
• Standard garden hose connection for water pressure, no additional power required
• Minimal water consumption, as low as 1.7 gallons per hour, for energy efficiency and low environmental impact.
• 8 foot water supply line connection from ring to base
• Two year warranty
• Made in the USA

GD-70DEA-HF-03 GD-70D,HF,(hydrogen fluoride),0.4-3.00 ppm, UL, w/ethernet & 4-20 mA outputs (Ethernet OFF) by RKI Instruments

RKI Instruments has been making high quality gas detection and monitoring units for over 15 years. With an emphasis on safety and reliability, RKI Instruments excels at providing the best products in gas detection and sensor technology on the market. Every year, RKI strives to improve its product offering and scours the globe for the latest technologies and innovative designs. With the introduction of the GD-70D Series Intelligent Gas Detector, employers and workplace safety managers can feel confident that they have purchased a reliable detector that is built to last.

GD-70D Series Intelligent Gas Detector

The GD-70D Series Intelligent Gas Detector is a new smart gas detection transmitter that monitors combustibles, oxygen, and a wide range of toxic gases. The unit can be used as a standalone device, integrated with other PLC systems, or integrated with RKI's Beacon series of single and multi-channel controllers. Its common platform integrates numerous detection methods and requires very little maintenance.

Exclusive Features

The plug and play intelligent sensors make for easy setup and calibration by internally retaining calibration and sensor data. This allows workers to replace sensors while in the field without the need to reprogram the equipment. For little maintenance and optimal reliability, the internal technology automatically adjusts for long-term zero and span drift. The pump flow is also self-tuning for low maintenance functioning. In general, the smart sensors use electrochemical cell detection, semiconductor detection, pyrolysis-particle detection, galvanic cell detection, and catalytic combustion detection.

The GD-70D Series features a large LCD display that easily reads all notifications and provides a color coded graph for alarm status (first and second alarms are red, and fault alarms are yellow). The LCD screen displays the pyrolyzer connection, gas concentration, detection unit of measurement, the detected gas, the maintenance status, sensor identification, the flow rate, a graph of gas concentration, error codes, and alarm points. All operational settings are completely user adjustable from the front panel. The unit also has a self-diagnosing function which detects sensor trouble and system failure. The Intelligent Gas Detector has a convenient troubleshoot feature through its firmware. This allows users to investigate and resolve their own equipment issues while minimizing maintenance costs.

Specifications

The Intelligent Gas Detector is a convenient size for workplace and wall space efficiency with dimensions of 2.8"D x 4.7"H x 5.9"D and weighs approximately 2 pounds. It can be mounted to a wall easily with a base plate and 2 or 3 screws. Sensor replacements and pump replacements can be performed quick and easily without tools.

*Please note we can only ship RKI products to customers within the United States

TOC-635 Control Panel with CO2 detector 0-40,000 ppm prewired 10 m cable by IGD

Pioneering Technology

State-of-the-art addressable gas detection in one compact package. The TOC-635 Control Panel is the central hub of your addressable gas detection system and the interface through which you can control your entire setup. Equipped with Sentinel+™ digital communication software and 2-Wire Addressable technology, IGDs advanced gas detection system is designed to provide fast, efficient, accurate performance to protect personnel and plant against gas hazards.

Our Detectably Better system utilises a 2-core polarity-independent cable helping to reduce system costs and offering unparalleled flexibility, accommodating up to 8 (Micro) or 99 (Plus) additional devices linked in series. Link alarms, interface with plant shutdown hardware, and communicate clearly with BMS and similar systems.

Complete Control

The Plus offers all the same features as the Micro while also boasting 2 digital inputs and built-in Wi-Fi allowing you to download system reports and perform system servicing. Optional cloud-based data acquisition enables the remote monitoring of your system's status in real-time from any laptop, mobile phone, or tablet and supports email & text-based alarm notifications. Both models accommodate integration into 3rd party systems such as BMS and fire management systems. The Plus also boasts BACnet/Modbus compatibility. The 2×8 RGB display allows for intuitive interfacing and clear audible and visual alarms. The TOC-635 features assignable LEDs, 1-Click auto-setup and Jog-Wheel interfacing offering complete control and total peace of mind.

Advanced 2-Wire Addressable Gas Detection

2-Wire Addressable technology combines with our Sentinel+™ digital communication software, to provide an advanced addressable gas detection system designed to offer fast, efficient, and error-free performance. The 2-Wire Addressable system also allows you to link multiple detectors in series on our 2-Core cable providing unparalleled versatility and huge savings on installation and allowing for seamless integration into your setup.

Key features include:

• Auto-find
• Auto-configure
• Auto-update
• Downloadable status reports

Sentinel+™ accommodates interfacing with your safety systems, communication with all hardware and BMS and the addition of alarms, and other external devices. Our 2-Wire Addressable solutions have no polarity requirements, which means we can minimise cabling and system costs without compromising on safety.

Installation Cables

• Supported installation cables 2 core 1.5mmSQ or 2.5mmSQ
• Typically SWA, MICC, SY, CY Screened or similar

MX6-L003Q202 MX6 iBrid Multi-Gas Monitor, LEL,O2,CO2IR,LE,D,F by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

3300-37-014 CC 33 Fixed Transmitter with Propadiene (MAPD) (C3H4), Stainless Steel Housing, 0-100% LEL (MK 208-3), RS 485 with Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

GD-70D4X-MH21KS GD-70D Smart Transmitter, H2, Specific, 0-1000 ppm, in NEMA 4X Housing by RKI Instruments

RKI Instruments has been making high quality gas detection and monitoring units for over 15 years. With an emphasis on safety and reliability, RKI Instruments excels at providing the best products in gas detection and sensor technology on the market. Every year, RKI strives to improve its product offering and scours the globe for the latest technologies and innovative designs. With the introduction of the GD-70D Series Intelligent Gas Detector, employers and workplace safety managers can feel confident that they have purchased a reliable detector that is built to last.

GD-70D Series Intelligent Gas Detector

The GD-70D Series Intelligent Gas Detector is a new smart gas detection transmitter that monitors combustibles, oxygen, and a wide range of toxic gases. The unit can be used as a standalone device, integrated with other PLC systems, or integrated with RKI's Beacon series of single and multi-channel controllers. Its common platform integrates numerous detection methods and requires very little maintenance.

Exclusive Features

The plug and play intelligent sensors make for easy setup and calibration by internally retaining calibration and sensor data. This allows workers to replace sensors while in the field without the need to reprogram the equipment. For little maintenance and optimal reliability, the internal technology automatically adjusts for long-term zero and span drift. The pump flow is also self-tuning for low maintenance functioning. In general, the smart sensors use electrochemical cell detection, semiconductor detection, pyrolysis-particle detection, galvanic cell detection, and catalytic combustion detection.

The GD-70D Series features a large LCD display that easily reads all notifications and provides a color coded graph for alarm status (first and second alarms are red, and fault alarms are yellow). The LCD screen displays the pyrolyzer connection, gas concentration, detection unit of measurement, the detected gas, the maintenance status, sensor identification, the flow rate, a graph of gas concentration, error codes, and alarm points. All operational settings are completely user adjustable from the front panel. The unit also has a self-diagnosing function which detects sensor trouble and system failure. The Intelligent Gas Detector has a convenient troubleshoot feature through its firmware. This allows users to investigate and resolve their own equipment issues while minimizing maintenance costs.

Specifications

The Intelligent Gas Detector is a convenient size for workplace and wall space efficiency with dimensions of 2.8 D x 4.7 H x 5.9 D and weighs approximately 2 pounds. It can be mounted to a wall easily with a base plate and 2 or 3 screws. Sensor replacements and pump replacements can be performed quick and easily without tools.

*Please note we can only ship RKI products to customers within the United States

6203-0013 MVR-300 Variable Refrigerant Flow Gas Detector, 100-240VAC, Low and High Alarm, Modbus, LED and 80dB Alarm - R-407c, 0 to 10000 ppm by Bacharach

The MVR-300 detector is specifically designed to provide continuous monitoring for refrigerants associated with high-efficiency, high volume refrigerant cooling and heating systems, such as VRF/VRV (Variable Refrigerant Flow/Variable Refrigerant Volume) sytems. Typical applications include hotels, dormitories, hospitals, office buildings, and apartment buildings.

The MVR-300 audible and visual alarms alert occupants and simultaneously communicate to Building Management Systems/Building Automation Systems (BMS/BAS). Two on-board relays can be used to close valves, activate alarm devices and exhaust fans or initiate emergency calls to rescue teams.

The on-board Modbus RTU interface provides real-time information about refrigerant concentrations, status and settings. It also enables custom configuration of the MVR-300 to any application specific requirements using multiple Modbus registers. The MVR-300 is designed for easy installation and simple maintenance.

The MVR-300 is compatible with MVR-SC Controller.

Features

• Fits in standard electrical boxes
• Low profile/Flush mount
• Two relays and Modbus Communications
• Alarm options including: LED, buzzer, two levels, configurable delay and failsafe
• Refrigerant specific sensor
• Self diagnostics and simple field calibration
• Unique plug-in field replaceable pre-calibrated sensor

Benefits

• Easy to install
• Aesthetically non-intrusive appearance
• Notify building management & initiate counter measures
• Alert occupants and remotely inform building management of alarm location for rapid response as required
• Enhances safety and minimizes refrigerant loss
• Easy to maintain
• Low cost of ownership

VP5-L123A101411 Ventis Pro Series, LEL (Methane), CO, H2S, O2, Li-ion Wi-fi Battery, Desktop Charger, Orange, ANZEx, LENS™ Wireless, English by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

72-PEA-D GX-3R Pro 4 Gas Personal Monitor - LEL / O2 / CO - CO2, 10,000 ppm, IR (ETA Aug 2019) - Li-Ion Battery Pack with 12 VDC Charger and Vehicle Plug by RKI Instruments

The GX-3R Pro is the world's smallest 5-gas monitor weighing only 4.58 ounces and fits in the palm of your hand (2.9" W x 2.6" H x 1.06" D). It simultaneously monitors and displays 5 different gases. In addition to monitoring standard confined space gases, LEL, O₂, CO, & H₂S, the GX-3R Pro has a 5th channel where you can add infrared or toxic sensors. Two of the four sensor slots have interchangeable sensors providing flexible configurations, which can easily be changed in the field.

The GX-3R Pro comes equipped with Bluetooth wireless communication, man-down alarm, the choice of alkaline or rechargeable power supply, and a 3 year warranty. The Lithium-ion battery pack will operate for 25 hours and will fully charge in 3 hours.

The GX-3R Pro utilizes Bluetooth communication to display direct gas readings from the instrument to a phone app, which is available free on either iOS or Android phones. Automatic notifications can be programmed to send text or email messages, if there is an alarm event from the GX-3R Pro.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 5 gas monitor: 2.9" W x 2.6" H x 1.06" D , 4.58 ounces
• Simultaneous detection of 5 gases: LEL, O₂, H₂S, CO, and other optional sensors; H₂ Compensated CO sensor available
• Simple 2-button operation
• Bluetooth communication with iOS & Android App
• Non-Compliance Indicator
• 3 user adjustable alarm levels
• Panic Alarm - Tap instrument twice
• Man Down Alarm
• Impact resistant body
• Large full dot, auto-backlit display with auto-rotation
• Stealth mode for law enforcement
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

B225 Zobell ORP Calibration Solution by Sensorex

Use this pre-mixed ORP calibration solution for verifying and calibrating ORP sensors.The solution standard is 228mV and is widely used for ORP sensor calibration. Supplied in a pint (16oz) bottle with long term stability.

Features:

• Simple calibration of ORP sensors to known standard
• Fast response time with all ORP sensors
• No mixing required - solution is pre-mixed and instantly ready for use
• One year shelf life guaranteed

GD-70DPEA-TEOS GD-70D Smart Transmitter with pyrolyzer, TEOS(tetraethyl orthosilicate), 0-15ppm, with Ethernet and4-20mA out by RKI Instruments

RKI Instruments has been making high quality gas detection and monitoring units for over 15 years. With an emphasis on safety and reliability, RKI Instruments excels at providing the best products in gas detection and sensor technology on the market. Every year, RKI strives to improve its product offering and scours the globe for the latest technologies and innovative designs. With the introduction of the GD-70D Series Intelligent Gas Detector, employers and workplace safety managers can feel confident that they have purchased a reliable detector that is built to last.

GD-70D Series Intelligent Gas Detector

The GD-70D Series Intelligent Gas Detector is a new smart gas detection transmitter that monitors combustibles, oxygen, and a wide range of toxic gases. The unit can be used as a standalone device, integrated with other PLC systems, or integrated with RKI's Beacon series of single and multi-channel controllers. Its common platform integrates numerous detection methods and requires very little maintenance.

Exclusive Features

The plug and play intelligent sensors make for easy setup and calibration by internally retaining calibration and sensor data. This allows workers to replace sensors while in the field without the need to reprogram the equipment. For little maintenance and optimal reliability, the internal technology automatically adjusts for long-term zero and span drift. The pump flow is also self-tuning for low maintenance functioning. In general, the smart sensors use electrochemical cell detection, semiconductor detection, pyrolysis-particle detection, galvanic cell detection, and catalytic combustion detection.

The GD-70D Series features a large LCD display that easily reads all notifications and provides a color coded graph for alarm status (first and second alarms are red, and fault alarms are yellow). The LCD screen displays the pyrolyzer connection, gas concentration, detection unit of measurement, the detected gas, the maintenance status, sensor identification, the flow rate, a graph of gas concentration, error codes, and alarm points. All operational settings are completely user adjustable from the front panel. The unit also has a self-diagnosing function which detects sensor trouble and system failure. The Intelligent Gas Detector has a convenient troubleshoot feature through its firmware. This allows users to investigate and resolve their own equipment issues while minimizing maintenance costs.

Specifications

The Intelligent Gas Detector is a convenient size for workplace and wall space efficiency with dimensions of 2.8"D x 4.7"H x 5.9"D and weighs approximately 2 pounds. It can be mounted to a wall easily with a base plate and 2 or 3 screws. Sensor replacements and pump replacements can be performed quick and easily without tools.

*Please note we can only ship RKI products to customers within the United States

BZ1-Q14D000201 Radius BZ1 Area Monitor, CO2 (IR), CO, NO2, NO, No Pump, ATEx/IECEx, English by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas