All Products

2811-724-007 EC 28 Gas Transmitter with Nitrogen Oxide (NO), 0 - 300.0 ppm, Display / Modbus by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

MX6-N45DR211 MX6 iBrid Multi-Gas Monitor, CH4 (IR), NO2, SO2, NO, PID, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, English by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

104299 Amino Acid Reagent Powder Pillow, 25-mL, pk/100 by AquaPhoenix

For determination of high range silica by the silicomolybdate method (Hach method 8185) Range: 1-100.0 mg/L SiO2. Also used in the iodometric method (Hach method 10100) for the determination of high range hypchlorite (50-150 g/L as Cl2). Pack of 100 powder pillows.

BZ1-R44GG01113 Radius BZ1 Area Monitor, PID, NO2 (DualSense), CO/H2 Low (DualSense), Pump, UL/CSA, LENS Wireless, Spanish by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

MX6-L603R213 MX6 iBrid Multi-Gas Monitor, LEL (Methane), NH3, O2, PID, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, Spanish by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

MX6-L67BR217 MX6 iBrid Multi-Gas Monitor, LEL (Methane), NH3, Cl2, HCN, PID, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, Portugese by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

Part Number: W03-4002-000

72-PNA-D GX-3R Pro 3 Gas Personal Monitor - combo H2S / CO - CO2, 10,000 ppm, IR (ETA Aug 2019) - Li-Ion Battery Pack with 12 VDC Charger and Vehicle Plug by RKI Instruments

The GX-3R Pro is the world's smallest 5-gas monitor weighing only 4.58 ounces and fits in the palm of your hand (2.9" W x 2.6" H x 1.06" D). It simultaneously monitors and displays 5 different gases. In addition to monitoring standard confined space gases, LEL, O₂, CO, & H₂S, the GX-3R Pro has a 5th channel where you can add infrared or toxic sensors. Two of the four sensor slots have interchangeable sensors providing flexible configurations, which can easily be changed in the field.

The GX-3R Pro comes equipped with Bluetooth wireless communication, man-down alarm, the choice of alkaline or rechargeable power supply, and a 3 year warranty. The Lithium-ion battery pack will operate for 25 hours and will fully charge in 3 hours.

The GX-3R Pro utilizes Bluetooth communication to display direct gas readings from the instrument to a phone app, which is available free on either iOS or Android phones. Automatic notifications can be programmed to send text or email messages, if there is an alarm event from the GX-3R Pro.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 5 gas monitor: 2.9" W x 2.6" H x 1.06" D , 4.58 ounces
• Simultaneous detection of 5 gases: LEL, O₂, H₂S, CO, and other optional sensors; H₂ Compensated CO sensor available
• Simple 2-button operation
• Bluetooth communication with iOS & Android App
• Non-Compliance Indicator
• 3 user adjustable alarm levels
• Panic Alarm - Tap instrument twice
• Man Down Alarm
• Impact resistant body
• Large full dot, auto-backlit display with auto-rotation
• Stealth mode for law enforcement
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

BZ1-Q39B001214 Radius BZ1 Area Monitor, CO2 (IR), O2, PH3, HCN, Pump, ATEx/IECEx, LENS Wireless, German by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

MX6-LG03N211 MX6 iBrid Multi-Gas Monitor, CH4,CO/H2,O2,CH4 IR,LE,P,E by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

Part Number: P126550LM6

*Please note we can only ship RKI products to customers within the United States

MX6-0C206211 MX6 iBrid Multi-Gas Monitor, H2, H2S, NH3, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, English by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

BZ1-0100000111 Radius BZ1 Area Monitor, CO, No Pump, UL/CSA, LENS Wireless, English by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

VTS-M0432001301 Ventis MX4 Multi-Gas Monitor, CH4 (0-5%), NO2, O2, Li-ion Ext Range, No Charger, Without Pump, Orange, MSHA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

*Please note we can only ship RKI products to customers within the United States

F08-E001-010 DC Wireless Alarm Bar Kit, Remote, 2.4GHz, ATEX/IECEX by RAE Systems

The Wireless Alarm Bar communicates with the MeshGuard product family network. Each alarm bar comes with a pair of xenon strobe lights and a 112 dB horn to provide remote notifications of hazards in a work environment. A Wireless Alarm Bar can be configured as a Remote device that connects to the FMC 2000 controller.

When configured as a Remote device, the alarm bar will mirror the alarm settings in the controller. When the Wireless Alarm Bar is configured as a Host device, it becomes a stand-alone alert notification system that communicates directly with the remote monitors in a Mesh network.

• Wirelessly triggers alarm notification in hazardous environments
• Hazardous area certification
• Functions as a wireless router, extending the range of a wireless mesh network
• Can act as a wireless system host by communicating directly with MeshGuard gas monitors

Key Features

• Turn-key wireless alarm bar solution, mounted and pre-wired with two xenon lights and a 112dB horn
• Wireless transmission distance of 1,000 ft (300m) point-to-point. Range can be extended by using additional RAEPoint Wireless Relays
• Continuously powered by standard 12-28VDC input (DC version) or 110 AC (AC version)
• Explosion-proof enclosure for hazardous environment applications
• Battery driven option

Applications

• Oil and gas exploration
• Pulp and paper industry
• Refineries and petrochemical plants
• Fenceline monitoring

8100-4C LH The Striker LED Lighthead, 100ft 14/3 SOOW cable, EXP Proof Power Box, and 15A Plug, Includes Hook and Dome Diffuser by Western Technology

Shine a light on the darkest of work site conditions with The STRIKER™: 8100 LED, the ultimate explosion proof long handle work light. From typical hand-held use to hook mounting this versatile light harnesses the best of portability and durability for almost any application! Part of our Kick-It Tough™ Explosion Proof Lighting!

Features

• Blasting, Drop Light, Inspection, Painting ... One Work Light, Many Applications!
• Approved for: Class I, Div 1 & 2; Groups C & D
• Approved for: Class II, Div 1 & 2; Groups E, F, & G
• Approved for: CSA Zones 1 & 2; Zones 20, 21, & 22
• Rated for use in Canada
• Certified portable luminary
• Complies with explosion proof/hazardous location requirements
• XP-G Cree LED
• 7 Cool White LEDs emitting color at ~6000K with CRI of 70
• >1,750 lumens
• Standard Optic 50 degree refractive
• Optional Optics: 30, 45, or 60 reflective
• Temperature Rating: T5 (-40C to +40C) / T4 (-40C to + 100C)
• Options: Mounting Hook, Diffuser

GD-70DLN-NS GD-70D Smart Transmitter, without Sensor / Amp Unit, with Cable Gland, Lonworks by RKI Instruments

RKI Instruments has been making high quality gas detection and monitoring units for over 15 years. With an emphasis on safety and reliability, RKI Instruments excels at providing the best products in gas detection and sensor technology on the market. Every year, RKI strives to improve its product offering and scours the globe for the latest technologies and innovative designs. With the introduction of the GD-70D Series Intelligent Gas Detector, employers and workplace safety managers can feel confident that they have purchased a reliable detector that is built to last.

GD-70D Series Intelligent Gas Detector

The GD-70D Series Intelligent Gas Detector is a new smart gas detection transmitter that monitors combustibles, oxygen, and a wide range of toxic gases. The unit can be used as a standalone device, integrated with other PLC systems, or integrated with RKI's Beacon series of single and multi-channel controllers. Its common platform integrates numerous detection methods and requires very little maintenance.

Exclusive Features

The plug and play intelligent sensors make for easy setup and calibration by internally retaining calibration and sensor data. This allows workers to replace sensors while in the field without the need to reprogram the equipment. For little maintenance and optimal reliability, the internal technology automatically adjusts for long-term zero and span drift. The pump flow is also self-tuning for low maintenance functioning. In general, the smart sensors use electrochemical cell detection, semiconductor detection, pyrolysis-particle detection, galvanic cell detection, and catalytic combustion detection.

The GD-70D Series features a large LCD display that easily reads all notifications and provides a color coded graph for alarm status (first and second alarms are red, and fault alarms are yellow). The LCD screen displays the pyrolyzer connection, gas concentration, detection unit of measurement, the detected gas, the maintenance status, sensor identification, the flow rate, a graph of gas concentration, error codes, and alarm points. All operational settings are completely user adjustable from the front panel. The unit also has a self-diagnosing function which detects sensor trouble and system failure. The Intelligent Gas Detector has a convenient troubleshoot feature through its firmware. This allows users to investigate and resolve their own equipment issues while minimizing maintenance costs.

Specifications

The Intelligent Gas Detector is a convenient size for workplace and wall space efficiency with dimensions of 2.8 D x 4.7 H x 5.9 D and weighs approximately 2 pounds. It can be mounted to a wall easily with a base plate and 2 or 3 screws. Sensor replacements and pump replacements can be performed quick and easily without tools.

*Please note we can only ship RKI products to customers within the United States