All Products

0699 6447/3 6447 Compressed Air Meter by Testo

The compressed air counters testo 6441 to testo 6444 are designed for the measurement, monitoring and recording of compressed air consumption, and therefore also for the determination of leakages in compressed air systems, consumption-based allocation of costs and the implementation of peak load management. The compressed air counters testo 6441 to testo 6444 record norm volume flow according to the calorimetric principle, which means the measurement procedure is independent of the process pressure and does not cause a permanent pressure drop.

The version testo 6447 offers everything the testo 6446 provides, in addition the removal of the probe under pressure is possible (patented screw fitting). The larger nominal values refer especially to important compressed air pipelines, often the main supply line after preparation.

• Measurement of norm volume flow in the measuring range 6.7 to 27500 m³/h (DN65 to DN350 or 21/2"-10")
• Exchangeable fitting: Probe removal under pressure possible (testo 6447 only)
• Material selectable between galvanized steel and stainless steel
• Highest flexibility thanks to different signal outputs: Analog output 4 to 20 mA (4-wire), Pulse output, 2 switch outputs (parameterizable: consumption or volume flow-dependent, opener, closer, hysteresis, window)
• Built-in totalizer, even without additional analysis unit
• Operating menu with LED display
• Cleanable sensor

72-RP-C GX-3R 1-Gas Confined Space Monitor, CO with Li-Ion Battery Pack with 100-240 VAC Charger by RKI Instruments

OSHA defines the breathing zone as a ten inch radius around the worker's nose and mouth, and requires that worker exposure monitoring air samples be collected in the breathing zone. Air sampling filters may be attached to the collar or lapel. Traditionally this means only a single gas monitor would be small enough for a worker to practically wear a gas monitor 'In the breathing zone'. Now there is a 4 gas monitor smaller than many single gas monitors.

The GX-3R is the worlds smallest 4 gas monitor weighing only 3.52 ounces and can comfortably be clipped within a worker's breathing zone (2.2" W x 2.55" H x 1.02" D). It simultaneously monitors and displays LEL combustibles, O₂, CO (Hydrogen compensated CO also available), and H₂S.

The GX-3R represents the latest evolution of gas detection technology utilizing a new generation of micro sensors. The LEL sensor has a unique design with two active filaments in one sensor to increase it's resistance to silicone poisoning. If one filament gets poisoned the second filament takes over. The new O₂ sensor is electrochemical with a 3 to 5 year life span. H₂S and CO are now available in a combo micro sensor.

Safety supervisors will appreciate the non-compliance indicator. The instrument flashes it's 3 LED lights every 30 seconds in the following conditions; if the instrument has not been bump tested, or if calibration is due, or if there was a gas alarm event. The 3 LED lights will continue to flash once every 30 seconds until the non-compliance condition has been resolved. The 30 second interval is adjustable.

Features

• Smallest & lightest 4 gas monitor: 2.2" W x 2.55" H x 1.02" D, 3.52 ounces
• Simultaneous detection of 4 gases: LEL, O2, H2S & CO; H2 Compensated CO sensor available
• Simple 2-button operation
• Non-Compliance Indicator
• Alarms: audible, visual, & vibration
• 3 user adjustable alarm levels
• Impact resistant body with removable rubber boot
• Large LCD Auto-backlit display
• 25 hours of operation (Lithium-ion battery)
• Field replaceable sensors & filters
• Water and dust resistant design, IP66/68
• Stealth mode for law enforcement
• 3 Year warranty

Applications

• Personal monitoring
• Confined spaces
• Refineries/petrochemical
• Utilities
• Oil and Gas
• Water/wastewater
• Fire services
• Construction

*Please note we can only ship RKI products to customers within the United States

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

10152669 Altair Pump Probe, North America by MSA

Built on durability

The ALTAIR Pump Probe joins a family of products with a pedigree of durability and functionality. A rugged unibody housing provides unsurpassed durability, including the ability to survive a 10-foot drop. With a large, glove-friendly button for single handed use, the ALTAIR Pump Probe is designed for easy use in any work environment.

Flexibility to meet your needs

Users who occasionally need to use diffusion instruments for pumped applications, the ALTAIR Pump Probe is the ideal solution with sampling options using a sample wand or sample line of up to 50ft. With a universal design, the ALTAIR Pump Probe can be utilized with a number of MSA diffusion type portable gas detector instruments.

Designed with you in mind

The ALTAIR Pump Probe was designed around your needs with a translucent cap for easy filter inspection, tool-free quick change components for simplified maintenance, and compatibility with our ALTAIR chargers.

3177K1 Benchtop Conductivity Meter Kit by Jenco

Kit Includes:

• 3177 - Benchtop, Conductivity/Temperature/TDS Meter
• 101 - Epoxy/Carbon, 8-Pin Connector, K=1.0
• 6230D115 - AC Adapter, 9 VDC, Center Negative

The Basis Series Conductivity/TDS/Salinity benchtop is the latest entry-level meter from a line that is renowned for its reading quality, now with a refined user experience and improved usability.

• Renowned accuracy and repeatability
• Upgraded user experience and usability
• Low cost of ownership

Well-designed, Inside and Out

The Basis Series Conductivity/TDS/Salinity meter, along with the pH/mV model, forms the foundation of Jenco's benchtop meter offerings and comes from a long line of distinguished benchtop meters, where low cost of ownership, reading quality and build quality take precedent.

Benchtop Conductivity/TDS/Salinity Meter Renowned for Accuracy and Repeatability

The reason Jenco is consistently contracted to build products for well-respected brands and the reason we can consistently win the trust of end-users is due to our reputation for being focused on reading quality. Do the right things in the right way, no cutting corners.

• Repeatable readings with ±0.5% full scale accurate across entire measurement range
• Uses 2-wire conductivity cells with adjustable k=0.01, k=0.1, k=1 and k=10 cell constants for improved flexibility and accuracy
• Each and every unit is hand calibrated and QC'ed by at least 2 teams
• Simple one point calibration

Upgraded User Experience and Usability

While the Basis Series provides the quality readings you expect, it does so in a design that optimizes its user-friendliness and minimizes its footprint on your workstation.

• Streamlined, modern and smaller design creates clutter-free workspace
• Large, high contrast LCD
• Convenient one point calibration
• Automatically determines the best conductivity ranges to display readings
• Well-situated keys with tactile feedback
• Splash-resistant case made with durable, reinforced plastic for added protection
• AC adaptor or battery powered

Improved Electrode Serviceability and Low Cost of Ownership

The Basis Series Conductivity/TDS/Salinity meter uses a common Jenco 8-pin DIN connector so it works with our other conductivity electrodes. The decision to make the electrode arm a detached, optional accessory further allows the Basis Series to be setup in the way that works best for you.

• Splash-resistant case is made with durable, reinforced plastic for added protection
• 8-pin DIN connector for conductivity cell & 10k thermistor
• Optional, detached electrode arm

*Please note we can only ship RKI products to customers within the United States

5918-0900 GDC-350 Gas Sensor Monitor, NEMA 1 Housing, SO2 Sensor w/ Pre-wired Supply by Bacharach

Bacharach's all new GDC-350 full-featured fixed gas monitors provide superior operation - standalone or as part of a larger system utilizing the standard analog outputs. This state-of-the-art instrument can detect a wide range of gases including carbon monoxide (CO), oxygen (O2), combustible gases, refrigerants and total volatile organic compounds (TVOCs). The GDC-350 provides a unique two sensor interface, allowing for multiple gases to be detected with onboard or remote sensors. Sensors can be located integral to the unit or remotely allowing for sensors to be placed directly in areas where potential leaks can occur. Bacharach s proprietary calibration algorithms extend the amount of time required between calibrations, reducing maintenance costs and lowering the overall cost of ownership for non-critical applications.

The GDC-350 has all the features and functionality for any application. LED alarm indicators visually indicate when alarm conditions are met and an audible alarm alerts nearby personnel. An onboard alpha numeric display shows gas readings in real time for each sensor. Integral dry contact relays are available to drive external audible / visual alarms, activate fans, or connect to building management and control systems. Installation and maintenance is simple and easy, reducing overall system cost. A pre-wired plug-in option is available for out-of-the-box operation. Simply plug the unit into any standard AC outlet for immediate detection and protection.

AQ Comfort-2 Kit with CO2 and Ambient Temperature, Continous Sampling Pump, AC Charger, Rechargeable Batteries, Manual, Calibration Certificate by E Instruments

Accurate / Reliable / Robust / Fast

• IAQ Tool for HVAC Professionals
• Real-Time Data Logging
• Active Internal Sampling Pump
• Compact Handheld Unit
• Large Internal Memory (2000)
• Protective Magnetic Rubber Boot
• Optional Wireless Printer
• Optional Handheld Probe

• CO2, CO, Temperature, %RH, Wet Bulb, Dew Point, Barometric Pressure
• Long Lasting Rechargeable Battery & AC Charger
• Easy to Use Menu System
• Optional PC Software & USB Cable

All AQ Comfort Kits Include:

• Continuous Active Internal Sampling Pump
• Differential Pressure
• Differential Temperature
• Long Lasting Battery & AC Charger
• Factory Calibration Certificate
• Operating Manual

Part Number: 58L-433

6300-4032 MGS-150 Gas Transmitter, NH3: 0 - 1,000 ppm, IP66 Housing w/Remote Sensor by Bacharach

MGS-150 Series Gas Transmitter is a feature-rich gas detection system with a wide range of sensor options to provide real-time monitoring of refrigerant, combustible, and toxic gases. It comes standard with user-selectable analog and digital outputs that can be set for 4-20 mA, 0-5V, 1-5V, 0-10V, or 2-10V; allowing them to connect directly to most BMS, SCADA or control systems. Alarm indicators include an onboard alarm LED and audible buzzer, in addition to an alarm relay for connection to external audible/visual alarms or a BMS system. The product's alarm threshold value is pre-set to factory defaults but is also field programmable. A variety of housing options are available (shown below), from standard IP41 enclosures to IP66 water resistant housings, which allow the MGS-150 Series gas sensors to be placed in the toughest of conditions.

Ideal for Commercial and Industrial Refrigeration, Food Storage and Food Processing Facilities, Supermarkets, Parking Garages, Wastewater Treatment Facilities, Hospitals and Universities.

Features & Benefits:

• Infrared, semiconductor and electrochemical sensor options to meet almost any gas detection need - at the most affordable cost.
• User-selectable analog outputs: 4-20 mA, 0-5V, 0-10V, 1-5V, 2-10V featuring 12/24 VAC/VDC operation.
• Fast-response sensors detect leaks quickly, which protect personnel and minimize refrigerant gas usage and environmental impact.
• Long-life semiconductor sensors for detection of all refrigerants, ammonia, halocarbons, combustible gases & VOCs.
• Robust design and remote sensor options allow units to be placed directly in areas where detection is needed.
• Available in a variety of housings, including IP66 and duct mount, for placement in the toughest of environments.

Part Number: 34L-62A-50

LabSen 821 Glass-body pH Electrode for Dairy Products and Liquid Food by Apera

Backed by proprietary Swiss sensor technologies and materials, the LabSen® 821 Combination pH Electrode/Probe is designed for testing the pH for dairy products such as milk, cream, yogurt, and other liquid food such as mayonnaise, jam, BBQ sauce, syrup, etc.

Silver Ion Trap Reference System+Protelyte Electrolyte - The LabSen® 821 pH Electrode/Probe adopts a Silver Ion Trap reference system and Protelyte reference solution. On top of the Long-Life reference system, a silver ion trap is added to prevent the junction from being blocked or contaminated by proteins.

LabSen unique blue hemispherical glass membrane - faster response time, better repeatability, and built tough, highly resistant to general impact (totally differentiates from the traditional fragile glass bulb membrane); and can be tested in high-temperature samples (up to 225°F).

The electrode uses a BNC connector, compatible with any pH meters that use BNC connectors, such as Apera Instruments MP511, PH850, PH8500, PH700, PH910, PH950, PH820 and PC820. The temperature sensor is not built-in. Users need to have a separate temperature probe (ex: Apera Instruments MP500) to enable ATC or manually input temperature to realize temperature compensation.

The electrode is backed up with a 6-month warranty by Apera Instruments.

• Proprietary pH sensor technology and materials from Switzerland
• Designed for milk and other liquid food that contain proteins
• Unique LabSen® hemispherical glass membrane, which has a faster response rate, better repeatability, and built tough
• Silver Ion Trap Reference System + Protelyte reference solution, preventing the electrode being contaminated by proteins
• Standard BNC Connector

723-110-P2-1K Eagle 2 Portable Monitor, Oxy/H2S(0-1000 ppm)/VOC(PID 0-2, 000ppm) by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5 L x 5.25 W x 5.875 H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States