$500 - $750

CS22 CS22 Fixed Transmitter (no sensor), no display, 4-20 mA by GfG

Wherever toxic or flammable gases and vapors must be monitored without requirements for explosion protection, the use of the CS22 is recommended.

Proven and cost-effective

The CS22 works on the principle of chemisorption (CS). Thanks to a wide range of monitorable gases and multiple measurement ranges, the CS22 offers a wide range of uses, from laboratories to industrial applications to refrigeration systems.

Transmitters with electrochemical sensors (EC), are also used with toxic and flammable gases. In contrast, the CS22 is a much more durable and cost-efficient solution. However, the environmental parameters must fit.

Communicates analog and digital

The measured values and status information of the CS22 can be transmitted either analog (4-20 mA or 0.2-1 mA) or digital (RS-485). This allows not only the use in combination with any GfG controller, but also the connection to programmable logic controllers (PLC).

Smart measured value processing

Industry-wide, the trend is towards smart units, such as the CS22, whose integrated electronics process the data already at the measuring point. The linearization of the measurement signal, compensation of temperature influences, detection of malfunctions and information on the next service or maintenance interval are just some of the advantages that result.

Variants for every requirement

The basic version of the CS22 is sufficient for many applications. If a measured value display on site is desired, there is also a variant with display and acoustic alarm.

CS22 Basic variant for a wide range of catalytic sensors
CS22 D with display to show the current measured value

In combination with GfG's powerful controllers, both variants are the right choice for a wide range of gases to be monitored.

Part Number: M5C01BAT08B

9250NKA Handheld Polarographic Meter with Memory & RS-232 Kit by Jenco

Includes:

• 9250N Handheld Polarographic Meter with Memory & RS-232
• LD-900-8-DO Stainless Steel Field Probe with 8-Pin Connector & 10-ft Cable
• LD-900-03A Membrane Kit with 6 Caps & KCL Solution

MCXL-X00M-Y-OR GasAlertMicroClip XL Detector, Oxygen (O2), Carbon Monoxide (CO) - Yellow Housing, OR Version (Other Regions, 3-pin UK plug) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXLX00MYOR

*Please note we can only ship RKI products to customers within the United States

GD-A8-H2 GD-A8 Diffusion Detector Assembly, 0 - 100% LEL, Hydrogen by RKI Instruments

Features

• Compact & lightweight
• Easy maintenance
• Quick-fit sensor replacement
• Compatible sensor for diffusion sampling and sample drawing detector heads
• Long life sampling pump (GD-D8V series)
• Explosion proof
• Wide variety of accessories

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

MCXL-00HM-Y-OR GasAlertMicroClip XL Detector, Hydrogen Sulfide (H2S), Carbon Monoxide (CO) - Yellow Housing, OR Version (Other Regions, 3-pin UK plug) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXL00HMYOR

WD-35419-12 pH 700 Benchtop Meter Only with Stand, 110/220 VAC, 50/60 Hz by Oakton

The easy-to-use, microprocessor-based pH 700 benchtop meter measures pH, mV, relative mV, and temperature. The large, dual-display LCD provides excellent visibility even from a distance. Automatic temperature compensation (ATC) maintains reading accuracy even with fluctuating temperatures. Five-point pH calibration, with automatic buffer recognition for both USA (pH 1.68, 4.01, 7.00, 10.01, 12.45) and NIST (pH 1.68, 4.01, 6.86, 9.18, 12.45) pH buffers, makes for easy calibration no matter which requirement you need to meet. Meter features HOLD, ATC, and electrode diagnostics. The convenient pull-out quick reference card keeps procedures handy at all times. Meter accepts any pH or ORP electrodes with a BNC connector.

As always, our waterproof meters are IP67-rated for both dust and water intrusion. Even with no probes attached!

• Compact footprint is over 40% smaller than other benchtop meters
• Large display permits easier readout viewing
• Datalogging allows you to store and recall up to 100 data sets

18100060-GB Gasbadge Pro Single Gas Monitor, CO/H2 NULL, BRAZIL INMETRO by Industrial Scientific

Built to Industrial Scientific's highest quality and reliability standards, GasBadge® Pro provides a lifetime of gas hazard protection with more features than any other single gas monitor available. Interchangeable "smart" sensors enable the GasBadge Pro to be quickly adapted to monitor unsafe levels of oxygen or any one of the following toxic gases: carbon monoxide, hydrogen sulfide, nitrogen dioxide, sulfur dioxide, chlorine, chlorine dioxide, phosphine, ammonia, hydrogen cyanide and hydrogen. GasBadge Pro communicates directly via an infrared interface to optional accessories like the DSX Docking Station, Datalink and infrared printer to further simplify and automate calibration, function (bump) testing and data downloading. Standard STEL and TWA readings, and datalogging of up to one year of survey data are featured along with an event-logger that records the past 15 alarm events.

Housed in a rugged enclosure, the monitor is immune to RF, water resistant and extremely durable. A protective concussion-proof overmold protects the unit from extreme abuse in a variety of harsh industrial environments. It's simple and intuitive four-button navigation allows easy access to setup, operation and calibration functions.

• Interchangeable "smart" sensors monitor oxygen or any one of many toxic gases
• One-year data logging capacity (minimum)
• Standard STEL and TWA
• iNet® ready and DSX™ Docking Station compatible

6350NKC pH/Conductivity/Salinity/mV/Temp. Handheld Meter with RS-232 Kit by Jenco

The Jenco 6350 is a high performance pH/Conductivity/Salinity/mV/Temp. handheld meter in a splash proof case with an RS-232C interface that allows it to communicate with any IBM compatible PC. This meter is CE approved and features 0.01 pH Resolution and a mV range of ± Salinity is in the range of 0.0 to 80.0 ppt with a 0.0 ppt resolution. Conductivity Cells are selectable for K=1.0 or K=5.0 and ranges are selectable for uS or mS.

Includes:

• 6350N pH/Conductivity/Salinity/mV/Temp. Handheld Meter with RS-232
• 600P pH/ref eledtrode
• model 101 K=1.0 cond. cell
• 6230D115 AC Adapter
• 6350F carrying case

• pH buffer recognition: model 6350 (pH:7.00,4.01,10.01) , model 6350c (pH:6.86,4,9.18)
• Selectable 2/4 wire cells for long cable length & wide measurement range
• Store 50 sets of data in non-volatile memory
• Conductivity auto/manual range
• Power down memory backup
• Splash resistant/watertight case
• Audio feedback keys
• Battery/ac adaptor
• RS-232c output

18100060-9B Gasbadge Pro Single Gas Monitor, PH3, BRAZIL INMETRO by Industrial Scientific

Built to Industrial Scientific's highest quality and reliability standards, GasBadge® Pro provides a lifetime of gas hazard protection with more features than any other single gas monitor available. Interchangeable "smart" sensors enable the GasBadge Pro to be quickly adapted to monitor unsafe levels of oxygen or any one of the following toxic gases: carbon monoxide, hydrogen sulfide, nitrogen dioxide, sulfur dioxide, chlorine, chlorine dioxide, phosphine, ammonia, hydrogen cyanide and hydrogen. GasBadge Pro communicates directly via an infrared interface to optional accessories like the DSX Docking Station, Datalink and infrared printer to further simplify and automate calibration, function (bump) testing and data downloading. Standard STEL and TWA readings, and datalogging of up to one year of survey data are featured along with an event-logger that records the past 15 alarm events.

Housed in a rugged enclosure, the monitor is immune to RF, water resistant and extremely durable. A protective concussion-proof overmold protects the unit from extreme abuse in a variety of harsh industrial environments. It's simple and intuitive four-button navigation allows easy access to setup, operation and calibration functions.

• Interchangeable "smart" sensors monitor oxygen or any one of many toxic gases
• One-year data logging capacity (minimum)
• Standard STEL and TWA
• iNet® ready and DSX™ Docking Station compatible

MCXL-X0H0-B-CN GasAlertMicroClip XL Detector, Oxygen (O2), Hydrogen Sulfide (H2S) - Black Housing, CN Version (China/New Zealand) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXLX0H0BCN

*Please note we can only ship RKI products to customers within the United States

PC400S Portable pH/Conductivity Meter with GLP Data Management and USB Output by Apera

The Apera Instruments PC400S provides reliable pH and EC measurements with various intelligent functions and a durable structure. Equipped with Apera's high quality 3-in-1 pH electrode and BPB (Brush-Resistant Platinum Black) conductivity sensor, the meter tests pH, EC, TDS, and temperature in a quick and accurate manner.

Intelligent Functions: Quick & Easy 1 to 5 Points Auto Calibration. The Smart Self-Diagnosis helps you conduct proper calibrations and determine the condition of your probes. GLP Data management (1000 groups of data storage), USB data output and power supply. Timing measuring/data logging mode and Smart calibration reminder function available. Purified water and ammonia-added purified water measuring modes available. The large clear LCD displays pH/EC and temperature simultaneously along with icons of stable readings and finished calibrations.

Reliable Structure: IP57 Waterproof and Dustproof, ideal for use in harsh environments. It comes with a complete test kit including a meter, a pH electrode, a conductivity electrode, a USB cable, and 6 bottles of calibration solutions all in a rugged carrying case. Powered by AA Batteries. Two-Year warranty for the meter. CE certified.

• The high quality 3-in-1 pH Combination electrode and BPB Conductivity Electrode ensure Quick & Accurate pH and EC measurements
• IP57 Waterproof and Dustproof, ideal for use in harsh environments
• The large backlit LCD displays EC/pH and temperature simultaneously along with icons of stable readings and finished calibrations.
• GLP Data management (1000 groups of data storage), USB data output and power supply
• Quick and Easy 1 to 5 points auto calibration with calibration reminder function (premixed standard solutions included)

6300-2114 MGS-150 Gas Transmitter, CH4: 0 - 2,000 ppm (SC), IP66 Housing by Bacharach

MGS-150 Series Gas Transmitter is a feature-rich gas detection system with a wide range of sensor options to provide real-time monitoring of refrigerant, combustible, and toxic gases. It comes standard with user-selectable analog and digital outputs that can be set for 4-20 mA, 0-5V, 1-5V, 0-10V, or 2-10V; allowing them to connect directly to most BMS, SCADA or control systems. Alarm indicators include an onboard alarm LED and audible buzzer, in addition to an alarm relay for connection to external audible/visual alarms or a BMS system. The product's alarm threshold value is pre-set to factory defaults but is also field programmable. A variety of housing options are available (shown below), from standard IP41 enclosures to IP66 water resistant housings, which allow the MGS-150 Series gas sensors to be placed in the toughest of conditions.

Ideal for Commercial and Industrial Refrigeration, Food Storage and Food Processing Facilities, Supermarkets, Parking Garages, Wastewater Treatment Facilities, Hospitals and Universities.

Features & Benefits:

• Infrared, semiconductor and electrochemical sensor options to meet almost any gas detection need - at the most affordable cost.
• User-selectable analog outputs: 4-20 mA, 0-5V, 0-10V, 1-5V, 2-10V featuring 12/24 VAC/VDC operation.
• Fast-response sensors detect leaks quickly, which protect personnel and minimize refrigerant gas usage and environmental impact.
• Long-life semiconductor sensors for detection of all refrigerants, ammonia, halocarbons, combustible gases & VOCs.
• Robust design and remote sensor options allow units to be placed directly in areas where detection is needed.
• Available in a variety of housings, including IP66 and duct mount, for placement in the toughest of environments.

2210009E ZD 21 Fixed Gas Transmitter, Base Unit (no sensor) by GfG

A particularly long sensor life makes the ZD 21 a low cost transmitter for oxygen monitoring. The expected lifetime of the sensor is 5 years in continuous operation. A robust aluminum casing protects the sensor and the circuitry from impacts, splashed water, and dirt.

The ZD 21 is an "intelligent" transmitter. The comprehensive electronics allow for easy operation and maintenance and also increase operational safety and accuracy. In less than 2 seconds the ZD 21 responds to oxygen escaping from a leak. This extremely short response time allows the time to take measures to prevent considerable damage.

• Extremely stable oxygen (O2) sensor lasts 5 years
• Fast response
• No influences from pressure, humidity, or temperature
• No damage from carbon dioxide (CO2)