$2000 - $4000

2060-1 UV Flame Detector (660) - Aluminium by Crowcon

Crowcon supplies a wide range of detectors designed to detect flames extremely quickly and over long distances. The detectors can operate in difficult envonmental conditions and incorporate sophisticated algorithms and logic to prevent false alarms.

Features:

• Explosion proof ATEX, FM, CSA and GOST-R standards
• IR, UV, UV/IR and IR3 options
• Aluminium or stainless steel construction
• 4-20mA, RS-485 or standard 4-wire relay operation

T01-0100-000 AutoRAE Lite Automated Test and Calibration Station for ToxiRAE 3 by RAE Systems

The AutoRAE Lite high-speed, low-operating-cost bump test and calibration station stores data in a text file that can be opened by any spreadsheet or editor. Providing the lowest cost of ownership, the AutoRAE Lite allows you to bump test 700 monitors on one set of batteries.

In addition, the AutoRAE Lite operates on a low-pressure system with a built-in pump.

AutoRAE Lite includes

• AutoRAE Lite as specified
• USB cable for PC set up
• 12-volt power supply
• Demand-flow regulator (installed)
• SD memory card 512MB
• Quick-start guide
• Inlet filter
• CD includes: Operation manual, Drivers, Utility software

Key Features

• Fully automated bump and calibration
• Bump test in 12 seconds
• Full calibration in 2 minutes
• Gas usage only 70 cm³ per bump test
• Tamper-proof data files
• Configures monitor
• "No gas flow" alarm
• Hidden tubing
• Demand-flow system with included regulator

Applications

• Emergency response
• Environmental
• Fire service
• Industrial safety
• Oil and gas

2811-722-004 EC 28 Gas Transmitter with Sensor, Nitrogen Dioxide (NO2), Display / Alarm / Relay by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2087-1 UV Flame Detector (20/20U) by Crowcon

Crowcon supplies a wide range of detectors designed to detect flames extremely quickly and over long distances. The detectors can operate in difficult envonmental conditions and incorporate sophisticated algorithms and logic to prevent false alarms.

Features:

• Explosion proof ATEX, FM, CSA and GOST-R standards
• IR, UV, UV/IR and IR3 options
• Aluminium or stainless steel construction
• 4-20mA, RS-485 or standard 4-wire relay operation

M5IR-XWBH-R-D-D-B-N-00 GasAlertMicro 5 IR Detector CO2 (IR), % LEL, O2, H2S - Rechargeable Battery - Black Housing by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5IRXWBHRDDBN00

10184794 Altair 4XR Multigas Detector by MSA

Outfitted with rapid-response MSA XCell® sensors, the ALTAIR 4XR Gas Detector is the toughest 4-gas monitor on the market and is backed by a 4-year warranty. The ALTAIR 4XR can also provide real-time incident awareness to team members, supervisors, safety managers and others when paired with the MSA ALTAIR Connect app via a Bluetooth® wireless connection.

Real-time

• Sense gas 2 times faster than the industry average with our XCell sensors
• Quickly update MSA ALTAIR 4XR settings via the ALTAIR Connect app (available on the Google Play Store)
• Send event notifications via text message with the ALTAIR Connect app

Rugged

• Survives 25 drops from 4 feet (1.2 meters) (MIL-STD-810G drop protection)
• Can survive an incidental 25-foot (7.5-m) drop onto concrete
• Dust- and waterproof IP68 rating (2 meters for at least 1 hour)
• Operating temperature range: -40°F to +140°F (-40°C to +60°C)

Reliable

• 4-year instrument & sensor warranty
• Confirm compliance quickly with the Bump LED & on-screen checkmark
• Bump and calibrate with 1/2 the test gas and in 1/2 the time vs. industry average
• Bump and calibrate at a specified "Time of Day" with your MSA GALAXY® GX2 Automated Test System
• MotionAlert option tells others that user has become immobile
• User-activated InstantAlert notifies others of a potentially dangerous situation

WD-35414-00 PC 2700 Meter with pH Electrode, Conductivity/Temp Probe, Electrode Stand, and Software by Oakton

Your all-in-one solution for multiparameter research work in the lab!

The PC 2700 meter offers a new compact design that is over 40% smaller than other benchtop meters. The large display is easy to read even at a distance and features stability indication. All measurements include temperature display. The meter includes auto-buffer recognition for both USA and NIST pH buffer sets, automatic or manual temperature compensation, temperature in °F or °C, and display Hold. A calibration due alarm function means no more out-dated calibrations. The water-resistant membrane keypad offers password protection for both set-up and calibration.

Multiple pH slopes and offset display enables quick, easy electrode diagnosis. The electrode holder can be mounted on either side of the meter. The convenient pull-out, quick-reference card keeps keypad functions at your fingertips

• PC 2700 measures pH, ORP, ion, conductivity, total dissolved solids (TDS), salinity, resistivity, and temperature
• Measures salinity from 0.0 to 80 ppt and resistivity from 2.000 ohms to 20.0 Mohms
• Brilliant backlit display with dynamic stability indication
• Up to 500 point memory with date-time stamp for GLP
• Output data to printer or PC
• Accepts either 2-cell or 4-cell electrodes
• Features auto-standardization, auto-calibration, and autoranging
• Calibration due alarm with password protection for setup and calibration
• Temperature coefficient of 0.000 to 10.000%
• Automatic or manual temperature compensation

2901-21-003 IR 29 Di Gas Transmitter with Rotatable Display, IP67, Acetylene (C2H2), 0 - 100 LEL by GfG

Measuring Principle

IR transmitters have become recognized as reliable gas warning systems for explosion protection. They are used to detect individual combustible gases or a wide range of gases. This involves sending an IR beam with a certain light intensity through a measuring space and then capturing it with a detector. Parts of this beam are absorbed by, amongst other things, hydrocarbon molecules. The reduced light intensity of the beam is registered by beam detectors and converted into a signal as the existing % LEL gas concentration.

Benefits

A special feature of our IR technology is its ability to also measure combustible gases above the lower explosion limit. Moreover, the measurement does not require oxygen.

With this technology there is basically no risk of contaminating the sensor, through silicone vapors or hydrogen sulfide, when using catalytic combustion sensors.

Operation

IR transmitters are usually used with 2 wavelengths, a so-called reference wavelength and just one measuring wavelength. Strict limits are applied to these systems. The absorption spectra of many hydrocarbons are located in the wavelength range of 3.3 μm and overlap to a large extent.

This means that gases with overlapping spectra and just one measuring wavelength can no longer be clearly distinguished. Some hydrocarbons, e.g. the frequently used welding gas acetylene, are non-absorbing in the wavelength range of 3.3 µm, but absorb instead in neighboring wavelength ranges.

In many practical applications, it is not essentially important which gas is responsible for the explosion risk. Therefore, early warnings through the broadband measurement of hydrocarbons in order to monitor the lower explosion limit (LEL) must be guaranteed. False alarms with uncritical concentrations of individual gases or solvents are thus absolutely unacceptable.

These requirements are problems for systems with 2 wavelengths.

Patented GfG Technology

The internationally patented technology of the IR 29 has been developed to solve these problems. The gold-plated mirror optics of the sensor contains 2 radiators and up to 4 detector elements with different optical filters. The precisely calculated, microstructured and pure gold coated mirror optics of the IR 29 are supplied for the first time without beam splitters.

This helps to cut signal losses by 50 % and to completely avoid the physically-related disadvantages of a beam splitter. The measured values from two additional wavelengths (4 wavelengths in total) ensure improved detection of individual gases and thus enhanced selectivity. This results in the prevention of false alarms. Only a 4 wavelength system always guarantees early warnings and the simultaneous prevention of false alarms.

New Technology

The IR 29 is the first and only intrinsically safe IR gas transmitter with patented 4-beam 4-wavelength technology.

The ignition protection class "intrinsically safe", which is so essential for industrial plants and the mining industry, is achieved by the additional use of the SB1 safety barrier and its internationally patented and innovative design.

Complete Safety Even In Zone 0

The IR 29 is the first IR gas transmitter that can also be used in Ex zone 0 and which enables maintenance as well as replacement of the sensor head without additional expense when energized.

Universal Application

The IR 29 with its robust V4A stainless steel housing has been designed to withstand the harshest environmental conditions.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Internal Data Logger

A standard built-in data logger records all the measuring data, minimum / maximum values, average values and alarm events of the last 24 hours in a ring buffer.

The recording can also be shown on the display as a 2 and 8 hour trend indicator.

The histogram mode can be selected as a permanent display of the measured values. These values are continuously updated.

Graphical Display

Measured values are shown on the high-contrast graphical display. The display can be rotated 180° depending on the installation of the IR 29.

Self Diagnosis

Processor-based signal processing enables the systematic compensation of temperature dependencies, aging influences and soiling effects. Safety-relevant functions are monitored permanently via self-diagnosis procedures and a possibly required service is indicated automatically. Daily interfering factors, such as dust and dirt accumulation, are almost completely eliminated by the innovative design.

Pressure Sensor, Moisture and Temperature Compensation

The measuring accuracy of IR sensors depends on partial pressure and thus also air pressure. Climatic fluctuations or barometric high pressure therefore influence the measuring result. Furthermore, the absorption spectrum of water almost completely covers that of hydrocarbon absorption in the 2.7 to 3.3 μm range. Air humidity therefore initially generates a measuring signal the same as the actual measuring gas. This cross-sensitivity is of particular importance in warm areas with high relative humidity. An increase in the absolute water absorption capacity of air is not linear with the temperature, i.e. three times as much water can be absorbed at 40 °C than at 20 °C. This influence can only be compensated if the current moisture content of the air is known. The IR 29 can be optionally equipped with a pressure and moisture sensor for compensation.

Maximum Safety

The innovative display enables the realization of completely safe warning concepts.

Local displays and signals directly at the device can be used to provide an early warning of potential risks.

The display at the upstream safety barrier SB1 D enables the detection of risks outside the danger zone being monitored.

This allows immediate on-site action before really hazardous situations occur.

Dust Protection

A gas permeable, water-repellent diaphragm protects the absorption space of the transmitter against dust. The additional impact protection made from robust V4A stainless steel prevents mechanical damage to the optical components.

The diaphragm can be cleaned or replaced in a matter of minutes.

Remote Controls

The IR 29 transmitter does not feature control elements for setting or servicing tasks. This helps to prevent accidental or unauthorized manipulation.

Service work at the IR 29 transmitter is carried out using the RC 2 remote control.

Features

• First intrinsically safe infrared transmitter for explosion protection
• ATEX II 1G Ex ia IIC T4 Ga C0158 can also be used in Ex zone 0
• Temperature, moisture and pressure compensation
• Patented infrared technology (NDIR)
• The energized IR sensor head can be replaced in Ex areas
• Maintenance and service-friendly

G888C-130102000010 G888C gas monitor, 5 year O2 (lead free), 3 year ccLEL, CO, H2S, includes calibration cap, charging cradle with wall power adapter by GfG

The development of the Microtector III G888 focused on the requirements of a modern multi-gas detection instrument for use in personal protection. The result is a multi-gas warning device that is safe, robust and practical and has proven itself in daily working conditions.

Advantages

Safety through quality and functionality

Equipped with high-quality, precise and durable sensors that can be individually adapted to your requirements. Multitude of gas-combinations can be identified to ensure maximum safety of employees.

The well thought-out design of the housing and the menu navigation eases the operation of the multi-gas warning device under difficult conditions. This device features a rotating display, easily turning 180 degrees with just one click. For working in poorly lit conditions, the device conveniently features an explosion-protected LED light.

Designed for difficult working conditions

Sometimes there is a need to work in challenging environments; the Microtector III G888 is equipped to withstand such challenges. Ex zone 1 certified, the Microtector III G888 is dusttight and water-resistant in accordance to the IP 67 protection class. The rubberized polycarbonate housing makes the detector shock-resistant and will keep your device safe in case of a fall. It is also comfortable to wear, weighing only 275g.

Suitable for long operating times

Depending on the sensor equipment and configuration, the Microtector III G888 has an operating time of up to 65 hours.

Remote monitoring keeps employees safe

If the G888 with the radio module is used, teams can be monitored centrally via the portable GfG-Link or using a computer and an USB dongle. Information regarding the measured gas concentrations, alarm levels and the status of the man-down alarm will then be available in real time.

Be prepared for an emergency

In the event of an emergency it is always good to be prepared. The Microtector III G888 is able to simulate an alarm of any gas concentration, in order to train and prepare for a variety of emergency situations.

Maintenance and documentation

The test and docking stations for the Microtector III G888 not only allow location-independent, daily bump tests and regular functional checks, as well as the complete documentation.

G888 - the team player

The Microtector III G888 offers optimum individual protection for everyone working in hazardous and/or enclosed areas. When measuring releases of gas or searching for a gas leak, it is recommended to use the Polytectors III G999 from GfG, which has a built-in pump. The advantage: both devices can be remotely monitored by a computer or GfG-Link.

Gasmaster Control Panel for Gas and Fire Monitoring

Crowcon Detection Instruments is a global leader in gas detection and safety equipment. With over 40 years of experience in research and technology, Crowcon is consistently leading the industry in design innovation. By integrating historical successes with advances in modern technology, Crowcon is able to consistently produce high quality products that meet today s challenging environments.

The Gasmaster is an innovative self-contained control panel that monitors gas and fire hazards. Its exclusive features allow the control panel to be flexible enough to fit most industrial applications. More importantly, its outstanding performance and leading technology make this panel an industry leader.

Exclusive Gasmaster Features

Crowcon sGasmaster contains numerous features that outperform the competition in gas detection and safety standards:

• Easy to use control features
• Easy to read backlit LCD display
• Unparalleled flexibility and compatibility with existing equipment
• Reliable alarm and safety features

Easy to Use

The Gasmaster is incredibly easy to read and operate. The front mounted display simultaneously broadcasts all of the appropriate gas levels while indicating the system status check. The front panel also houses the buttons that control the systems operations. All features of the Gasmaster, including recalibration, can be controlled by these easy to operate keys. With the simple push of a button, any user can easily operate the system s features. The Gasmaster s system s software was also designed with ease of use in mind. The software enables reconfiguration and datalogging instantaneously and requires minimal training.

The backlit LCD display screen provides all of the necessary safety information without overwhelming the user. Utilizing a large clear screen, the alphanumeric display reads the gas levels, displays the system status, and illuminates an alarm bar when necessary.

Flexible and Adaptable

The state of the art Gasmaster is incredibly versatile and flexible. The unit can monitor and control virtually any combination of gas and fire detectors. The unit also offers a variety of outputs

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

C011029 Xgard Hazardous Area ESU EX, for Two Detectors by Crowcon

The Environmental Sampling Unit provides a cost-effective solution for monitoring high-density gases such as chlorine, sulphur dioxide and flammable vapours, in environments where the positioning of conventional sensors is not practical.

The sampling chamber is fitted with an electric fan, which draws an air sample via a pipe. Xgard gas detectors are fitted to the chamber to monitor for the presence of flammable or toxic gases.

Features:

• Can monitor up to 12 metres of perforated pipe using a fan-aspirated single sensor.
• Flameproof fan available for flammable gas applications.
• Fan-fail monitoring is available for up to four units using a Gasmaster control panel.
• Typical applications include gas detection in LPG and chlorine stores, flammable gas detection in wet wells.

2901-09-004 IR 29 i Gas Transmitter without Display, with Pressure and Humidity Compensation, IP67, Methane (CH4), 0 - 100 LEL by GfG

Measuring Principle

IR transmitters have become recognized as reliable gas warning systems for explosion protection. They are used to detect individual combustible gases or a wide range of gases. This involves sending an IR beam with a certain light intensity through a measuring space and then capturing it with a detector. Parts of this beam are absorbed by, amongst other things, hydrocarbon molecules. The reduced light intensity of the beam is registered by beam detectors and converted into a signal as the existing % LEL gas concentration.

Benefits

A special feature of our IR technology is its ability to also measure combustible gases above the lower explosion limit. Moreover, the measurement does not require oxygen.

With this technology there is basically no risk of contaminating the sensor, through silicone vapors or hydrogen sulfide, when using catalytic combustion sensors.

Operation

IR transmitters are usually used with 2 wavelengths, a so-called reference wavelength and just one measuring wavelength. Strict limits are applied to these systems. The absorption spectra of many hydrocarbons are located in the wavelength range of 3.3 μm and overlap to a large extent.

This means that gases with overlapping spectra and just one measuring wavelength can no longer be clearly distinguished. Some hydrocarbons, e.g. the frequently used welding gas acetylene, are non-absorbing in the wavelength range of 3.3 µm, but absorb instead in neighboring wavelength ranges.

In many practical applications, it is not essentially important which gas is responsible for the explosion risk. Therefore, early warnings through the broadband measurement of hydrocarbons in order to monitor the lower explosion limit (LEL) must be guaranteed. False alarms with uncritical concentrations of individual gases or solvents are thus absolutely unacceptable.

These requirements are problems for systems with 2 wavelengths.

Patented GfG Technology

The internationally patented technology of the IR 29 has been developed to solve these problems. The gold-plated mirror optics of the sensor contains 2 radiators and up to 4 detector elements with different optical filters. The precisely calculated, microstructured and pure gold coated mirror optics of the IR 29 are supplied for the first time without beam splitters.

This helps to cut signal losses by 50 % and to completely avoid the physically-related disadvantages of a beam splitter. The measured values from two additional wavelengths (4 wavelengths in total) ensure improved detection of individual gases and thus enhanced selectivity. This results in the prevention of false alarms. Only a 4 wavelength system always guarantees early warnings and the simultaneous prevention of false alarms.

New Technology

The IR 29 is the first and only intrinsically safe IR gas transmitter with patented 4-beam 4-wavelength technology.

The ignition protection class "intrinsically safe", which is so essential for industrial plants and the mining industry, is achieved by the additional use of the SB1 safety barrier and its internationally patented and innovative design.

Complete Safety Even In Zone 0

The IR 29 is the first IR gas transmitter that can also be used in Ex zone 0 and which enables maintenance as well as replacement of the sensor head without additional expense when energized.

Universal Application

The IR 29 with its robust V4A stainless steel housing has been designed to withstand the harshest environmental conditions.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Internal Data Logger

A standard built-in data logger records all the measuring data, minimum / maximum values, average values and alarm events of the last 24 hours in a ring buffer.

The recording can also be shown on the display as a 2 and 8 hour trend indicator.

The histogram mode can be selected as a permanent display of the measured values. These values are continuously updated.

Graphical Display

Measured values are shown on the high-contrast graphical display. The display can be rotated 180° depending on the installation of the IR 29.

Self Diagnosis

Processor-based signal processing enables the systematic compensation of temperature dependencies, aging influences and soiling effects. Safety-relevant functions are monitored permanently via self-diagnosis procedures and a possibly required service is indicated automatically. Daily interfering factors, such as dust and dirt accumulation, are almost completely eliminated by the innovative design.

Pressure Sensor, Moisture and Temperature Compensation

The measuring accuracy of IR sensors depends on partial pressure and thus also air pressure. Climatic fluctuations or barometric high pressure therefore influence the measuring result. Furthermore, the absorption spectrum of water almost completely covers that of hydrocarbon absorption in the 2.7 to 3.3 μm range. Air humidity therefore initially generates a measuring signal the same as the actual measuring gas. This cross-sensitivity is of particular importance in warm areas with high relative humidity. An increase in the absolute water absorption capacity of air is not linear with the temperature, i.e. three times as much water can be absorbed at 40 °C than at 20 °C. This influence can only be compensated if the current moisture content of the air is known. The IR 29 can be optionally equipped with a pressure and moisture sensor for compensation.

Maximum Safety

The innovative display enables the realization of completely safe warning concepts.

Local displays and signals directly at the device can be used to provide an early warning of potential risks.

The display at the upstream safety barrier SB1 D enables the detection of risks outside the danger zone being monitored.

This allows immediate on-site action before really hazardous situations occur.

Dust Protection

A gas permeable, water-repellent diaphragm protects the absorption space of the transmitter against dust. The additional impact protection made from robust V4A stainless steel prevents mechanical damage to the optical components.

The diaphragm can be cleaned or replaced in a matter of minutes.

Remote Controls

The IR 29 transmitter does not feature control elements for setting or servicing tasks. This helps to prevent accidental or unauthorized manipulation.

Service work at the IR 29 transmitter is carried out using the RC 2 remote control.

Features

• First intrinsically safe infrared transmitter for explosion protection
• ATEX II 1G Ex ia IIC T4 Ga C0158 can also be used in Ex zone 0
• Temperature, moisture and pressure compensation
• Patented infrared technology (NDIR)
• The energized IR sensor head can be replaced in Ex areas
• Maintenance and service-friendly

G999P-03-03-00-00-00-61-20 G999 Multi-gas Atmospheric Monitor, 5 year O2 (lead free), 3 year COSH, IR LEL includes calibration cap, cable, charging cradle and wall power adapter by GfG

The Microtector III G999 combines the demands of a modern multi-gas measurement device for protecting workers with the ability to safely measure confined spaces. As a robust and sophisticated multi-gas detector, it is versatile in its application and flexible in sensor combinations.

Advantages

Safety through quality and functionality

To fit every environment, there are three versions available. All versions include three electrochemical and one infrared sensor. Depending on the version, the G999 features a catalytic combustion (CC) sensor, a combined CC/semiconductor sensor, a PID sensor or a fourth electrochemical sensor. This allows a variety of gas combinations or measuring ranges to be defined and simultaneously monitored.

The well thought-out design of the housing and the menu navigation, allows for easy operation in difficult situations. For example, the display can be easily rotated 180°, so that it is always easy to read. For work in poorly lit rooms or in emergency situations, the G999 features an explosion-proof LED torch.

Designed for difficult working conditions

The Microtector III G999 is certified for use in Ex Zone 0 and is water and dust-proof according to protection class IP 67 and is suitable for challenging applications. The rubberized polycarbonate housing provides excellent protection against jolts and impacts, while the practical design and robust crocodile clip ensure optimum wearing comfort.

Ample Battery Power for Long Operating Times

Unlike other devices, the G999 features a double battery capacity of up to 130 hours of operation and provides power supply to the pump.

Remote Monitoring to Protect Employees

If devices with radio modules are used, teams can be monitored centrally via the portable GfG-Link or using a computer and USB dongle. Information regarding the measured gas concentrations, alarms and the status of the man-down alarm will then be available in real time.

Prepared for an Emergency - Alarm for Exercise

In the event of an alarm, knowing how to behave is highly important. By means of the alarm simulation any gas values can be transmitted to the Microtector III G999 to simulate and train different emergency scenarios.

Maintenance & Documentation – Location-Independent and Legally Compliant

The test and docking stations for the Microtector III G999 not only allow location-independent, daily display tests and regular functional checks, but also the complete documentation.

G888 – The Perfect Match

It is not always necessary to equip every employee with a gas detector including a pump for safe measurement of confined spaces, but everyone should have a modern multi-gas detector. In such situations the Microtector III G888 is recommended. Like the G999, it offers optimum individual protection for all those who have to work in hazardous areas and/or enclosed spaces.

VN01707 X-am 5800 Multi-Gas Detector with CATEX,O2/H2S-LC,CO,NH3,NIMH by Draeger

The X-am® 5800 multi-gas detector measures up to six gases and is equipped with a particularly shock-resistant CatEx sensor. With the Drager Gas Detection Connect software, it offers live data transmission and powerful asset management. Designed for personal monitoring, the X-am 5800 offers you the highest level of safety at a low cost of ownership.

Benefits

Powerful data analysis in the cloud

Safety and efficiency thanks to its networking capability: Transfer your recorded data directly and conveniently via Bluetooth® to a smartphone and from there to the backend of the Gas Detection Connect software. As an alternative, you can also transfer the data directly to the cloud with the X-dock test station. This way, you have secure access to your data and its analysis at any time and from anywhere – simply via your internet browser.

Comfortable asset management

With the X-am 5800 you can manage your fleet of equipment comfortably and efficiently in daily use. Save operating costs and time through fast tests by using the automatic test station X-dock with low gas consumption or a pure mechanical bump test station. Further advantages: powerful asset management via our smart software solution, convenient firmware updates in the X-dock, an optional RFID transponder and individual colour marking of the devices. Few, easy-to-replace spare parts – including the power supply – and sensors ensure that your devices remain operational for many years. Drager provides a 4-year manufacturer's warranty on the basic device. Existing, compatible accessories from its predecessor, the X-am® 2500/5000/5600 can continue to be used.

Tailor-made gas monitoring

Small and lightweight: The X-am 5800 is comfortable to wear and easy to use even with gloves on thanks to its large buttons. The display clearly shows important information such as gas readings, alarms and time. The green D-light indicates that the unit is ready for use. All this, plus the completely language-free icon based user interface, makes it pleasantly simple to use and familiarise yourself with. For your added safety, its oxygen channel has four alarm thresholds – real pre-alarms and main alarms for falling and rising concentrations. Approved for use in Ex zone 0, it has also been tested according to protection class IP 68.

Powerful sensors

The new CatEx sensor offers you even more advantages: readiness for calibration within seconds, extreme robustness against shocks and the measurement of flammable vapours – such as petrol, diesel and nonane. You can also set the measurement gas to methane, propane, hydrogen, and many other gases. The performance is complemented by Drager's simple cross calibration concept, in which the measurement gas, calibration gas and bump test gas can be specified individually. Upon testing, the X-am 5800 then takes over the necessary conversions. The sensor is target to meet the demanding requirements of the new IEC standard 60079-29-1 (International Electrotechnical Commission).

At the same time, the CatEx sensor is resistant to poisoning substances such as silicones and other harmful substances. This combination of properties is exceptional. With years of experience in sensor technology, Drager develops and produces the sensors itself, including the powerful and durable electrochemical sensors in the XXS format. Your advantage: sensors and device are perfectly matched to each other – saving you operating costs. We are currently developing a durable, power-saving infrared sensor to measure flammable gases and vapours and/or carbon dioxide, as well as a photo-ionisation detector sensor for measuring volatile organic compounds (VOCs). These can be used instead of the CatEx sensor.

Focus on sustainability

During the development of the X-am 5800, great importance was given to sustainability. The optimised Drager Sensors and the rechargeable power supply, which can be easily replaced with one screw, ensure it has a long service life. Almost all spare parts can be replaced by trained users, while all remaining parts can be repaired by Drager Service. Furthermore, existing accessories from the previous series can still be used. Environmental protection has also been taken into account in the technical documentation and packaging: Designed to save paper, when you order two or more units, we can reduce the number of instruction manuals supplied if you order the modular version. For your convenience, Drager also takes back old devices and ensures that they are recycled properly.

M5-XWSY-R-P-0-Y-N-00 GasAlertMicro 5 Detector %LEL, O2, H2S, CO, SO2 - NiMH Battery and Pump by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5XWSYRP0YN00

G888C-130102000010E G888C gas monitor, 5 year O2 (lead free), 3 year ccLEL, CO, H2S, includes calibration cap, charging cradle with wall power adapter and Bump kit by GfG

The development of the Microtector III G888 focused on the requirements of a modern multi-gas detection instrument for use in personal protection. The result is a multi-gas warning device that is safe, robust and practical and has proven itself in daily working conditions.

Advantages

Safety through quality and functionality

Equipped with high-quality, precise and durable sensors that can be individually adapted to your requirements. Multitude of gas-combinations can be identified to ensure maximum safety of employees.

The well thought-out design of the housing and the menu navigation eases the operation of the multi-gas warning device under difficult conditions. This device features a rotating display, easily turning 180 degrees with just one click. For working in poorly lit conditions, the device conveniently features an explosion-protected LED light.

Designed for difficult working conditions

Sometimes there is a need to work in challenging environments; the Microtector III G888 is equipped to withstand such challenges. Ex zone 1 certified, the Microtector III G888 is dusttight and water-resistant in accordance to the IP 67 protection class. The rubberized polycarbonate housing makes the detector shock-resistant and will keep your device safe in case of a fall. It is also comfortable to wear, weighing only 275g.

Suitable for long operating times

Depending on the sensor equipment and configuration, the Microtector III G888 has an operating time of up to 65 hours.

Remote monitoring keeps employees safe

If the G888 with the radio module is used, teams can be monitored centrally via the portable GfG-Link or using a computer and an USB dongle. Information regarding the measured gas concentrations, alarm levels and the status of the man-down alarm will then be available in real time.

Be prepared for an emergency

In the event of an emergency it is always good to be prepared. The Microtector III G888 is able to simulate an alarm of any gas concentration, in order to train and prepare for a variety of emergency situations.

Maintenance and documentation

The test and docking stations for the Microtector III G888 not only allow location-independent, daily bump tests and regular functional checks, as well as the complete documentation.

G888 - the team player

The Microtector III G888 offers optimum individual protection for everyone working in hazardous and/or enclosed areas. When measuring releases of gas or searching for a gas leak, it is recommended to use the Polytectors III G999 from GfG, which has a built-in pump. The advantage: both devices can be remotely monitored by a computer or GfG-Link.

T01-0100-000 AutoRAE Lite Automated Test and Calibration Station for ToxiRAE 3 by RAE Systems

The AutoRAE Lite high-speed, low-operating-cost bump test and calibration station stores data in a text file that can be opened by any spreadsheet or editor. Providing the lowest cost of ownership, the AutoRAE Lite allows you to bump test 700 monitors on one set of batteries.

In addition, the AutoRAE Lite operates on a low-pressure system with a built-in pump.

AutoRAE Lite includes

• AutoRAE Lite as specified
• USB cable for PC set up
• 12-volt power supply
• Demand-flow regulator (installed)
• SD memory card 512MB
• Quick-start guide
• Inlet filter
• CD includes: Operation manual, Drivers, Utility software

Key Features

• Fully automated bump and calibration
• Bump test in 12 seconds
• Full calibration in 2 minutes
• Gas usage only 70 cm³ per bump test
• Tamper-proof data files
• Configures monitor
• "No gas flow" alarm
• Hidden tubing
• Demand-flow system with included regulator

Applications

• Emergency response
• Environmental
• Fire service
• Industrial safety
• Oil and gas

72-5114RK Eagle Portable Monitor for Nitrogen Dioxide (NO2), 0 - 15 PPM by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

8326590 X-am 5100 Single-Gas Detector, H2O2 (US) by Draeger

For manufacturing petrochemical products, aseptic packing, or handling of rocket fuel: the Draeger X-am 5100 portable single-gas detector ensures safe handling of HF, HCl, H₂O₂ or hydrazine – thanks to proven Draeger sensor technology and a device design which is perfectly customized to reactive gases.

YOUR ADVANTAGES AT A GLANCE

• Continuous, precise and reliable measurement
• A special device design with direct gas entry provides fast sensor response and precise measurement data by preventing gas adsorption on the device housing
• Lightweight and robust
• Slip-proof and compact design
• Triple alarm: visual (360°), audible (multi-tone), vibration
• Easy to use: two-button operation and user-friendly menus
• Highly resistant to impacts, vibrations and electromagnetic radiation
• Can be operated using replaceable alkaline batteries or a T4 NiMH rechargeable battery, which can be charged right in the device

M5-XWAY-R-P-D-B-N-00 GasAlertMicro 5 Detector % LEL, O2, H2S, CO, NH3 - Rechargeable Battery and Pump - Black Housing by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5XWAYRPDBN00

M5IR-XWBH-R-D-0-Y-N-00 GasAlertMicro 5 IR Detector CO2 (IR), %LEL, O2, H2S - NiMH Battery by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5IRXWBHRD0YN00

42503 Gasurveyor 3 - 500 2 Button Portable Gas Detector - LEL, VOL by GMI

The GMI Gasurveyor 500 series is GMI's most technologically advanced range of gas detectors to date. GMI has developed this new range of standard instruments to cover the majority of your gas detection requirements.

Features

• Rechargeable or alkaline battery options
• Approved to European and North American safety standards
• Extremely robust anti-static case
• Simple to use, 2-button operation
• Built-in sampling pump as standard
• Large LCD with automatic backlighting in low level light conditions
• Audible/visual alarms for all gas ranges
• Fault alarms for low flow, low battery, etc.
• Compatible with the GMI range of Auto Calibration Systems

Includes

• G500 carrying case
• Harness
• Hex driver
• 1.5Mt clear sample line
• User manual
• Probe handle
• 35 cm probe (solid end)
• Sample line adaptor
• Dry cell batteries (not USA) or NiCad pack and cotton filters (20).