$2000 - $4000

2811-737-003M EC 28 Gas Transmitter with MODBUS, Ozone (O3), Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

2811-731-003M EC 28 Gas Transmitter with MODBUS, Sulfur Dioxide (SO2), Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

G450-11440C G450 Confined Space Kit with Flashlight Rechargeable Battery, O2, LEL, CO, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

73-0591RK RX-415 Dual Gas IR For LEL/Volume HC & Oxygen, 0 - 100% LEL & 0 - 100% Vol CH4, & 0 - 25% O2, Land Version (CH4 Calibration) by RKI Instruments

This model has two versions and is a combination type portable HC/O2 or CH4/O2 gas detector with an Infrared (NDIR) type sensor and galvanic cell type sensor. These sensors provide accurate detection of HC/O2 (HC version) or CH4/O2 (CH4 version) levels even in N2 and other inert environments. The measuring ranges are 0-100%LEL/0-100 vol% for HC or CH4 and 0-25 vol% for )2 respectively with automatic ranging. The RX-415 has explosion proof and intrinsically safe construction so that it can be used safely in any environment.

Features

• Available to measure from higher concentration (vol%) to lower concentration (%LEL)
• Explosion proof (Detector: Explosion proof, other electrical circuit and pump, intrinsically safe design)
• Available to measure HC/O2, CH4/O2 in N2, inert gas and air with a reliable NDIR method

Applications

• Measures gas concentrations in tank of LNG and LPG carriers
• Measures gas concentrations in crude oil tankers
• Measures gas concentration in inert gas generating system (IGS)

*Please note we can only ship RKI products to customers within the United States

VN00411 X-am 5000 Multi-Gas Detector, LEL, NH3, O2, H2S, Rechargeable Kit by Draeger

The Draeger X-am® 5000 belongs to a generation of gas detectors, developed especially for personal monitoring applications. This 1- to 5-gas detector reliably measures combustible gases and vapors as well as O₂ and harmful concentrations of toxic gases, organic vapors, odorant and amine.

Ergonomic mobile phone design

Despite its advanced functionality, the Draeger X-am® 5000's practical mobile phone design and light-weight make it comfortable to carry. Reduced to its essentials, the two-button control panel and easy-to-follow menu allow for intuitive use.

Flexible sensor exchange

It is easy to exchange, upgrade, or calibrate the sensors to other gases. The ability to customize the Draeger X-am® 5000's sensors makes more applications possible including the possibility to deploy in a rental fleet.

Poison-resistant Ex sensor

For improved safety when facing unknown and potentially explosive hazards—the Draeger X-am® 5000 provides dependable warnings in the event of explosive atmospheres due to the high level of sensitivity of the innovative catalytic ex sensor. It not only responds quickly to explosive gases and combustible organic vapors, it is also highly resistant against sensor poisons such as silicone and hydrogen sulfide. In combination with its long-term stability, this offers an extraordinarily long sensor lifetime of over four years. This will reduce operational costs.

Durable sensor technology

Equipped with durable XXS sensor technology, the Draeger X-am® 5000 offers maximum security at extremely low operational costs. The sensor's resistance, in combination with its long-term stability, provides the sensor with a lifetime in excess of four years, which can help reduce operational costs.

Robust and watertight

The Draeger X-am® 5000 is water and dust resistant, according to IP67 standards. The detector remains fully functional and ready for use, even after being dropped into water. The integrated rubber protection and shockproof sensors provide additional resistance to impact and vibration. Moreover, the Draeger X-am® 5000 is resistant to electromagnetic interference.

External pump

The optional external pump, which operates with a hose length of up to 45 meters (147 feet) long for the Mark II pump, makes it possible to use the detector for pre-entry measurements into confined spaces such as tanks, shafts, etc. The pump starts automatically when attached to the gas detector.

Area monitoring

In combination with the Draeger X-zone® 5500, the gas detector can be used for various area monitoring applications. Up to 25 Draeger X-zone® 5500 units can be automatically interconnected to form a wireless fence line. This interconnection of the area monitoring devices allow for the fast securing of larger areas, e.g. pipelines or industrial tanks—even within the scope of industrial shutdowns.

Optimum solutions for function or bump tests and calibrations

Simple, fast, and professional: from a function or bump test to complete documentation, users can choose from a range of practical, on-site solutions that offer maximum safety for every application. The automatic test and calibration station Draeger X-dock® and the Draeger Bump Test Station are ideal system extensions that save time and reduce workload. Fresh air, mixed gas and single gas calibrations can be done directly using the Draeger X-am® 5000 menu.

Flexible power supply

The Draeger X-am® 5000 can be used with the standard alkaline batteries. In addition, it can be fitted with a T4 battery that can be charged while still inside the instrument. The optional Save Energy Mode makes it possible to increase the operating time of the Draeger X-am® 5000 to more than 40 hours. This is done by selecting a measurement interval of either one second (the standard), 10 or 20 seconds for the CatEx sensor.

Novo 3 3-Gas Novo Basic Kit: O2, CO, CO2, NO, NOx, Combustion Efficiency, Excess Air, Draft, Pressure, Temperature, Calculations for High Efficiency & Condensing Systems, 12" Probe with 6' Hose, Hard Plastic Carrying Case, & Real-Time Bluetooth® Apps (iOS and Android) by Seitron Americas

• 7" Touch Screen for easy menu navigation
• Simultaneous Gas Pressure + Combustion Measurements
• Optional Built-in Printer
• Long Life O2 Sensor (4 Years)
• New Dual Range (Low/High) Sensor Technology
• Low NOx and SOx sensors
• 15 Preprogrammed Fuels
• Including Natural Gas, Oil, Propane, & Biofuels
• CO Protection Dilution Pump
• Rechargeable Li-Ion Batteries
• Integrated water trap with LED backlight for easy maintenance
• Differential Pressure Manometer
• Draft Measurement
• Mobile App for iOS and Android

Every Kit Includes

• Combustion Analyzer
• Gas probe with 12" (300 mm) interchangeable tip
• 10 ft (3m) Single Connection Hose
• Integrated water trap
• Manometer Hoses
• Outdoor Combustion Air Temp Probe
• AC Power Adapter & Cable
• Hard plastic kit case
• Quick Guide
• Calibration Certificate

Main Features

• Precalibrated Gas Sensors
• Field Replaceable
• Altitude Adjustment
• Integrated magnets
• Automatic autozero (with gas sampling probe inserted in the chimney)
• Self-diagnosis with verification of the functions and status of the sensors
• Language selectable by User
• 100,000 test memory
• Dimensions: Analyzer 10.6x3.6x2.7in (270x93x68mm), weight 2 lbs (0.9Kg) - Kit 5x18x13in (125x465x335mm), weight 11 lbs (5Kg)

Measured Values

• Differential Flue Gas and Ambient Air Temperatures
• Incoming Air Temperature and Ambient Air Temperature
• Draft and Differential Pressure
• Ambient CO
• O2 and CO in flue gas

Calculated Values

• Combustion Efficiency, including condensing units
• Stack losses and excess air
• Flow velocity with optional Pitot tube
• CO Air Free

4021-TS-H RAM 4021 Respiratory Air Monitor with Toggle Switch, Carbon Monoxide (CO), Low H2 Interference CO Sensor by GfG

The RAM 4021 AutoCal® series is the unit of choice where specific and accurate measurement of carbon monoxide, oxygen or dew-point levels are required. Designed to meet OSHA requirements for monitoring of Grade D respirable air, this unit is equipped with a reliable electrochemical sensor that accurately indicates the level of carbon monoxide on an illuminated liquid crystal display. Adding versatility, this unit offers optional oxygen or dew point sensors for applications where detection or measurement is needed.

Calibration and maintenance are simple with our innovative AutoCal® system. Additional features including alarm relay contacts, user adjustable alarm point, low flow alarm indicator and many more make this unit an intelligent choice. The RAM 4021 is available in four models, the 4021 (CO), 4021-1 (CO and O2), 4021-DPX (CO and dew point levels) and 4021-PR (CO and additional relay to signal power loss to monitor, complies with newest NFPA regulation). All models may be purchased with or without airline filter systems

Respiratory air specifications

All GfG Instrumentation RAM Instruments satisfy the requirements of OSHA rule 29 CFR 1910.134 (d) (2) (ii) for carbon monoxide monitoring. They will also monitor Grade E air, generally specified for breathing air in cylinders (SCBA).

Wall mounted filter panel option

The 25, 50 and 100 CFM panels filter out dangerous toxins from supplied air sources and ensure clean, breathable air. The threestage filter system efficiently removes particulates, oil vapors and hydrocarbons from an air supply. After filtration, the regulator sets the pressure for the respiratory equipment and the manifold assembly provides multiple outlets for airline hose quick connections. The model 8025 panel includes two user female quick connect outlets; the 8050 includes four, and the 8100 includes eight. A 1/2" FPT connection is standard on all 50 and 100 CFM panels, and a 3/8" FPT connection is standard on all 25 CFM panels.

Features

• Continuous compressed air CO monitor
• Integrated dew point measurement
• Robust easy-to-operate design

Features

• RAM 4021 Monitor
• Carbon monoxide (CO) sensor
• Other sensors (as specified)
• Manual

FS10-R30 FS10 Stand Alone (Unitized) Electro-Optical Fire Detector, Copper-Free Aluminum Housing includes Alert / Fire Early Warning Relay, 30 ft Sensitivity (Latching Alert & Alarm Relays) by Honeywell Analytics

Our fire detection systems have been protecting electrostatic paint spray booths worldwide - with millions of booth operational hours and not a single fire loss.

Fire Sentry FS System 10™

A high-speed microprocessor based fire detection and process control system specially designed for liquid and powder coating applications, the Fire Sentry FS System 10™ quickly detects the presence of a flame, reacts by initiating a shutdown of the electrostatic finishing process in a matter of milliseconds; and effectively interrupts the fire before residues and wet paint films can ignite.

The Fire Sentry FS System 10 is the only system that provides a two-stage response: an ALERT for spray gun "fireball" type fires and if the fire continues, a FIRE ALARM is declared in 4-5 seconds.

The Fire Sentry FS System 10 is vastly superior to conventional detectors due to the electro-optical quantum infrared sensors array and the ability to accurately detect fires without false alarms. The FS System 10 is available in both wallmount controller and card controller configurations. (For additional information on card controller, consult the factory.)

The detector is mounted in an explosion-proof housing. The wall-mounted controller is a self-contained system mounted in a NEMA 12 enclosure with LCD display and LED status lights. Three 10-amp mechanical relays have been incorporated for shutting down the paint flow, electrostatics and conveyor. Event history and fire tech data are reported by the detector in real time and data, then stored in the controller's non-volatile memory. FirePic™ and SnapShot™ data can be downloaded from the RS-232 port of the controller from your PC. The controller may operate with one or two detectors.

Fire Sentry FS10-R Unitized

The Fire Sentry FS10-R Unitized is a multi-spectral infrared electro-optical flame detector designed specifically for liquid paint or powder spray booth applications. Based on the Fire Sentry FS System 10, the FS10-R Unitized flame detector meets the need for a stand-alone capability and complies with the NFPA 33 Standard. The WideBand IR™, NearBand IR, and Visible sensors combined with the advanced signal procession provide optimum performance. High spend fire response with optional factory sensitivity settings and alarm outputs provide the best, proven solution to fire detection for the Finishing Industry.

Features

• Multi-Spectral digital electro-optical infrared fire detector
• Meets requirements of NFPA 33
• Unique two-stage ALERT and FIRE ALARM response
• Immune to false alarms caused by arcs or corona discharges
• Built-in automatic "through the lens" self-test
• Not sensitive to background radiant energy sources such as paint heaters
• Not affected by absorbing smoke or paint solvent mist in liquid pant spray booths
• Sees through paint, powder or oil residue on detector's lens
• Digital communications with RS-485 interface
• FirePic™: retrieval of recorded pre-fire data
• SnapShot™: dynamic graphical display of what the detector sees

Applications (indoor use only)

• Liquid Paint Spray Lines
• Aerosol Filling
• Powder Coating Booths
• Curing Ovens

Operation

The Fire Sentry FS10-R Unitized detector is designed to operate with any approved fire alarm panel. Interface with fire alarm panel is accomplished using the detector's ALARM, ALERT and FAULT relays.

When power is applied, a self-test is automatically performed and the FAULT relay is energized to show that the detector has no faults. The front LED blinks every ten seconds to indicate normal operation.

In normal operation, the continuous spectral data stream of information from the sensor array is analyzed by the microprocessor. With two distinct relay outputs, the Fire Sentry FS10-R Unitized provides an ALERT output for spray gun "fireball" type fires, and if the fire continues a FIRE ALARM is declared in 4-5 seconds.

The detector stores all the pre-fire spectral data from the sensor array in non-volatile memory for retrieval and evaluation. The Fire Sentry FS10-R stores the last six FirePic™ events, each 8 seconds long; and 200 event histories with time and date stamp. The FirePic data can then be used to postulate the cause of the fire.

XNX-AMAV-FNIC1 XNX Universal Transmitter, ATEX M25 AL FF MPD IR CO2 VV by Honeywell Analytics

XNX Universal Transmitter, ATEX M25 AL FF HRT FOR TOX/O2 SNSRThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

66-6192-01-R VOC Pro (10.6 eV lamp) 0-10.00 ppm, Low Range Sensor/Transmitter, with J-box, 2 Relays by RKI Instruments

The VOC Pro Series Gas Detector is a versatile assembly that uses a PID sensor to detect a variety of gases. Wired power (12 to 35 VDC) with 4-20 mA analog and RS-485 Modbus outputs are standard. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• PID sensor options: —10.0 eV lamp / 11.7 eV / 10.6 eV ppb / 10.6 eV ppm
• Wired power (3-Wire), 12 to 35 VDC operating voltage
• Operating temperature range -40°C to +54°C Graphical LCD with LED backlight
• 3 Push-button interface (ADD, MENU, SUB) with corresponding magnetic, non-intrusive switches
• 2 Individually configurable alarms
• 2 Front panel LED indicators (amber and red)
• 2 Optional fully programmable alarm relays (dry contacts)
• Output options: 4-20mA (3-wire) analog, RS-485 modbus (4 wire)
• 1-Year warranty (see specifications)

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants

*Please note we can only ship RKI products to customers within the United States

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

2380-300 EC 38 Fixed Transmitter, Base Unit (no sensor) by GfG

The EC 38 transmitter uses advanced technology for the detection of toxic gases and oxygen levels. It is available in the standard version with horn strobe or with a stack light. This monitor has a NEMA 4X enclosure that makes the EC 38 suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to a GfG controller. Autocal® automatic calibration and maintenance is done effortlessly through push buttons. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming.

• Advanced transmitter for oxygen and a wide selection of toxic gases
• 24 VDC
• Available with stack light or standard version with horn strobe
• AutoCal® automatic calibration
• Alarm relays standard (low, high and fault)
• Linear 4-20 mA output signal
• NEMA 4X housing

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

723-115 Eagle 2 Portable Monitor for LEL & PPM/O2/SO2 by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

66-5B51-10-W AirLink Alert Wireless Transmitter, Hydrocarbons (CH4) 0-100% LEL, LDIR, dual battery powered, non explosion proof, 900 MHz radio by RKI Instruments

The RKI AirLink Alert series ambient air toxic gas detector is a versatile assembly that uses an electrochemical, infrared or PID sensor element to detect a variety of gases. Battery powered, it communicates wirelessly with controller. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, or PID sensor element
• Battery powered
• Operating temperature range of -40°C to +70°C
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• Graphical LCD with LED backlight
• Output options: wireless, 900 MHz or 2.4 GHz radio
• 1-Year warranty

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants
• Construction
• Temporary or permanent monitoring applications

*Please note we can only ship RKI products to customers within the United States

0699 6447/3 6447 Compressed Air Meter by Testo

The compressed air counters testo 6441 to testo 6444 are designed for the measurement, monitoring and recording of compressed air consumption, and therefore also for the determination of leakages in compressed air systems, consumption-based allocation of costs and the implementation of peak load management. The compressed air counters testo 6441 to testo 6444 record norm volume flow according to the calorimetric principle, which means the measurement procedure is independent of the process pressure and does not cause a permanent pressure drop.

The version testo 6447 offers everything the testo 6446 provides, in addition the removal of the probe under pressure is possible (patented screw fitting). The larger nominal values refer especially to important compressed air pipelines, often the main supply line after preparation.

• Measurement of norm volume flow in the measuring range 6.7 to 27500 m³/h (DN65 to DN350 or 21/2"-10")
• Exchangeable fitting: Probe removal under pressure possible (testo 6447 only)
• Material selectable between galvanized steel and stainless steel
• Highest flexibility thanks to different signal outputs: Analog output 4 to 20 mA (4-wire), Pulse output, 2 switch outputs (parameterizable: consumption or volume flow-dependent, opener, closer, hysteresis, window)
• Built-in totalizer, even without additional analysis unit
• Operating menu with LED display
• Cleanable sensor

66-5B93-20-W AirLink Alert Wireless Transmitter, VOC (10.6 eV PID) 0-200 ppm, dual battery powered, 900 MHz radio by RKI Instruments

The RKI AirLink Alert series ambient air toxic gas detector is a versatile assembly that uses an electrochemical, infrared or PID sensor element to detect a variety of gases. Battery powered, it communicates wirelessly with controller. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, or PID sensor element
• Battery powered
• Operating temperature range of -40°C to +70°C
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• Graphical LCD with LED backlight
• Output options: wireless, 900 MHz or 2.4 GHz radio
• 1-Year warranty

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants
• Construction
• Temporary or permanent monitoring applications

*Please note we can only ship RKI products to customers within the United States

66-6301-10-W AirLink T3A Sensor/Transmitter with j-box, Carbon Monoxide (CO), 0-1,000 ppm with 900 MHz radio by RKI Instruments

The AirLink T3A Series Gas Detector ambient air hazardous gas detector is a versatile assembly that uses an electrochemical, infrared, catalytic bead sensor element to detect a variety of gases. Wired power (12 to 35 VDC) with wireless communication controller. An RKI wireless T3A also has 4-20 mA analog and RS-485 Modbus outputs as standard. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, catalytic bead sensors
• Wired power (3-Wire), 12 to 35 VDC operating voltage
• Output options: Wireless 900 MHz or 2.4 GHz; 4-20mA (3-wire) analog; RS-485 modbus
• Operating temperature range -40°C to +54°C
• Graphical LCD with LED backlight
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• 2 Individually configurable alarms
• 2 Front panel LED indicators (amber and red)
• 2 Optional fully programmable alarm relays (dry contacts)

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants

*Please note we can only ship RKI products to customers within the United States