$200 - $300

Part Number: 116L-99-25

194 True RMS 50,000 Count DMM with CAT IV, 1000V Rating with A106 and GK13M by Test Products International

The Triple Display 194 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 194 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The meter also has RS232 output and software for recording information into a PC

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP: Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Data logging
• 50,000 count display
• 0.05% DCV basic accuracy
• Inductance, Frequency and Capacitance
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1
• CATIII-1000VC, CATIII-1000V, CAT IV-600V, CAT III 1000V
• True RMS DMM
• Time Stamp Logging
• Optional PC Output with A192
• Pulse Width
• Duty cycle (% pulse width modulation) for measuring modulating gas valves

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Motor start and run capacitance
• Frequency on controls and line voltages
• Record min/max voltage of controls and line voltages
• Temperature with optional temperature adapter (A310)
• Bar graph to indicate rapid fluctuations in measurements
• Voltage of direct drive DC motors
• Measure power supply voltage
• Match components
• Compare readings in circuits and components
• Frequency of line and control voltage

A254 AC/DC Amp Low Current Probe Adapter by Test Products International

Most TPI brand and any competitor DMM, clamp-on or oscilloscope having the capability of measuring up to 2000mV AC/DC (2V AC/DC), 10M Ohm input impedance, and equipped with industry standard spaced input jacks 19mm on center.

AM-DS1215 12"x15' Duct with Cinch Strap by Schaefer

Industry standard quality ducting for everyday use. Single ply, PVC vinyl-coated polyester fabric with 15-gage spring steel wire helix and external PVC wearstrip. PVC coated polyester fastening cuffs at both ends with industry standard spring buckle cinches. Flame retardant. Available in 8" (15', 25'), 12" (15', 25') and 20" (25') sizes. Integrated carrying bags available with 8"x 25', 12"x 25' and 20"x 25' ducts.

WD-35807-35 Teflon-junction, CPVC-body pH Electrode with Pt 100 temp (Use with pH 100, 200, 800, and 1000 controllers) by Oakton

A. In-line submersible electrodes feature a probe guard to protect sensor from damage. They can be placed in a tee fitting for in-line use. CPVC body with 3/4" NPT thread on both ends withstands temperatures up to 80°C.

B. Submersible electrodes are permanently encapsulated in a 3-ft pipe - perfect for tank installation. ABS plastic body withstands temperatures up to 80°C.

C. Semi-domed bulb electrodes with solution ground have a unique surface design that protects electrode from particulates and increases flow across the junction to keep the bulb clean. Graphite body acts as a solution ground. Withstand temperatures up to 100°C.

D. Self-cleaning flat electrodes have an innovative flat surface that prevents solids buildup. CPVC body with 3/4" NPT thread on both ends withstands temperatures up to 80°C.

E. PTFE junction electrodes are excellent for simple wastewater applications. PTFE junction and polymer gel reference electrolyte resist clogging. CPVC body with 3/4" NPT thread on both ends withstands temperatures up to 80°C.

F. PTFE junction electrodes with solution ground are excellent for tough wastewater applications. Solution ground pin eliminates ground loop and electrical noise problems. PTFE junction and polymer gel reference electrolyte resist clogging. Ryton body with 3/4" NPT thread on both ends withstands temperatures up to 100°C.

• Include BNC connector
• Built-in Pt RTD sensor with stripped ends for temperature (ATC) element
• ORP electrodes feature Pt band sensor
• Use electrodes with solution ground with our pH 200, 800, or 1000 controllers in areas with high electrical noise

*Please note we can only ship RKI products to customers within the United States

CS200TC-K=10 Light Duty Online Conductivity Sensor, Platinum, 12mm, TC, K=10 TL by Sensorex

The CS200 and CS200TC conductivity probes are a cost effective solution for measuring conductivity in light industrial and laboratory applications.

Models CS200 and CS200TC feature platinized measuring surfaces that provide accurate and repeatable measurements. Rugged epoxy bodies make the sensors virtually unbreakable. These are an excellent choice to use as standard laboratory conductivity electrodes.

By adding a simple mounting gland fitting, customers may use these in process applications. Mount them in-line, in a pipe "T" fitting, or submerse them into a tank.

Features

• Ideal for laboratory and light duty process applicationsAvailable with or without ATC (temperature sensor)
• Easy to submerge in a tank or mount inline in a pipe
• Cell constant choices of 0.1, 1, or 10
• Compatible with most portable and benchtop meters

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

Part Number: 58L-408

WD-27003-12 Self-cleaning pH Electrode, CPVC Housing, 100Ohm Pt RTD, Tinned End by Oakton

Note: 100 Ω Pt RTD ATC elements conform to DIN curve 43760.

• Flat surface prevents buildups, while fluid flow cleans surface for longer life
• Use with most meters and controllers - BNC connector and ATC element work with a variety of units
• Double junction for difficult applications

Part Number: Z105325PM29

*Please note we can only ship RKI products to customers within the United States