$200 - $300

SCT-108.002.31 SCT LEMA IR Thermo Anemometer by ScichemTech

Includes:

• 9V battery
• Instruction manual
• Carrying case

Features:

• A complete portable SCT meter for air velocity, air flow and temperature measurements.
• Simultaneous display air flow in CFM/CMM or air velocity plus ambient temperature
• Combination of hotwire and standard thermistor, deliver rapid and precise measurements event at low air velocity
• Infrared thermometer measures remote surface temperature to 999F (537C) with 30:1 distance to spot ratio and laser pointer
• Wide range measurements of air velocity, fast response time
• Multifunction for air flow measurements : m/s, km/h, ft/ min, knots, mile/h
• Super large LCD with dual function display, read the air velocity and temperature at the same time.
• Ac power operated.

Part Number: 58L-414

*Please note we can only ship RKI products to customers within the United States

Part Number: 34L-460

Part Number: 34L-436

0560 8314 830-T4 IR Thermometer, 30:1 optics & dual laser by Testo

This universal infrared thermometer is designed to perform fast and accurate surface temperature measurements in the HVAC area and industry. At a distance of 1 m the point diameter is only 3.6 cm. From a secure distance even smaller, difficult to access or dangerous targets can be measured without any problems. The new high resolution processor enables measurement results of unbelievable accuracy. And due to the min./max. function you can define your temperature limit values according to your needs. To control the limits with the help of an audible and visual alarm has never been easier.

• 30:1 optics for measuring temperature at a distance, even on small objects
• 2-point laser for spot sighting
• Display of current value and Hold value
• Emissivity determination with external temperature probe
• Audible and optical alarm when limit values are exceeded
• Fast measurement value recording at two measurements per second
• Display illumination
• °C contact measurement with connectable TC probe
• Input of upper and lower limit value

*Please note we can only ship RKI products to customers within the United States

6231M pH/mV/Temp Microprocessor Handheld Meter with 3-Point Calibration by Jenco

pH/mV/Temp. microprocessor handheld meter in splash proof case with 3 point calibration, 40 memory storage, BNC, pH/ORP connector with 8-pin DIN ATC connector. AC/DC power. CE Approved

• 3 point calibration
• 40 memory storage
• Power down memories
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficients
• ATC
• CE approved
• Splash resistant/watertight case
• Battery/ac adaptor
• High 50/60hz noise rejection
• UL approved ac line adaptor
• Aconventional 9v battery
• Highly reliable mechanical touch keys with audio feedback

Part Number: 44L-481

94035 Smart DewHeater Controller 2X by Celestron

Work smarter, not harder, when it comes to combating dew. The Smart DewHeater and Controller 2x prolongs your battery life by optimizing power usage for up to two dew heaters. The controller gathers and analyzes information in real time to warm your optics just enough to prevent dew.

The Smart DewHeater and Controller comes with two ports to control two dew heaters at once. You can use one port to heat your optical tube while the other warms a second optical tube, a guide scope, an eyepiece, or another accessory. The controller also features an additional 12V DC output port so you can power another 12V DC device, such as your mount.

The Smart DewHeater and Controller works seamlessly with Celestron's Dew Heater Rings, which have a built-in thermistor to provide temperature readings of the corrector lens. Third-party dew heater bands or straps are also compatible; you simply need to add Celestron's Thermistor for Smart DewHeater Controllers (sold separately).

Smart Controls

At the heart of the controller is a powerful microprocessor that gathers information from the sensors, computes the data, and automatically adjusts your dew heaters. The controller monitors the ambient temperature and humidity using its integrated environmental sensor and monitors the heaters' temperatures using thermistors.

You can run the Smart DewHeater and Controller 2x as a standalone accessory. Or, if you want to view data from the controller and make manual adjustments, you can connect it to your Celestron telescope's hand control or your PC. The controller works with NexStar+ or StarSense hand controls running the latest firmware or Celestron CPWI telescope control software, included with every Celestron mount.

Power

The Smart DewHeater and Controller 2x runs on a 12V DC battery (like our PowerTank Lithium Pro or PowerTank 17) and can handle a maximum power of 120W (10A max current @ 12V DC). The controller also features a 12V DC output port. You can use this extra port to power another device, like your mount. This way, you can power your entire setup from a single source. Resettable electronic fuses prevent damage if input or output current draw becomes too high.

NOTE: If you are using two dew heaters in heavy dew conditions and powering a 12V DC device, the controller may be operating near its power limit. In this case, one PowerTank Lithium Pro or PowerTank 17Ah will not have enough capacity to run your setup all night; you'll need a larger capacity battery or multiple batteries.

Unique Industrial Design

The Smart DewHeater and Controller 2x features a heavy-duty metal housing. Inside, a cooling fan protects the controller's electronics.

The Bridge – On top of the controller, you will find the bridge, which is home to the device's status LEDs and environmental sensors. It also helps with cable management. We have positioned the temperature and humidity sensors here, away from the control box and other components that could generate heat. Unlike competitor products, our sensors do not require additional cables to obtain accurate readings.

The LED lights on the bridge indicate the device's current status. The LEDs provide warnings if the controller is drawing more current than your power source can supply or if the battery charge needs recharging. You can dim the lights if you are under dark skies.

Mounting – The Celestron Smart DewHeater and Controller 2x mounts on your CGE or CG-5 dovetail with the integrated dovetail clamps. If you prefer to mount the controller on your tripod leg, use the included strap.

Smart DewHeater and Controller 2x comes complete with:

• Smart DewHeater and Controller 2x
• Tripod leg strap
• Controller power cable
• Power cable for external 12V DC device
• AUX cable for connecting to Celestron mounts
• Thermistor extension cable to attach to Celestron's Dew Heater Ring

Enhance your setup

We highly recommend pairing this controller with Celestron Dew Heater Rings. They fit seamlessly on your Schmidt corrector lens and will improve your observing or imaging year-round.

For the highest level of dew prevention, we also suggest adding a dew shield to your setup. While not required, a dew shield will cut down on the amount of power the controller needs to provide to the dew heater rings to keep your optics clear.

• Using real-time data, the controller provides just enough heat to prevent dew from forming, prolonging battery life
• "Smart control" system monitors ambient temperature and humidity and adjusts power to the dew heaters automatically
• Compatible with Celestron Dew Heater Rings and third-party heating bands or straps (with thermistor accessory)
• Supports up to two dew heaters plus one additional 12V DC device, such as your mount
• Works with your Celestron telescope's hand control or CPWI telescope control software so you can view data and make manual adjustments
• Mounts securely to your telescope's dovetail or tripod leg
• Durable metal housing features an integrated cooling fan to protect the controller's electronics

Part Number: 58L-446

94460-37 Traceable® Memory-Loc™ Datalogging Thermometer with Calibration; 1 Bottle Probe by Digi-Sense

Easily monitor temperatures overnight or for any time period stores over 1 million temperature observations. Datalogger will stop recording when storage is full and will not overwrite recorded data. Memory can be cleared after downloading data and alarm events. Set high and low alarms in 1° increments; alarm sounds when temperature rises above or falls below set points. The alarm tracking feature stores data for up to 10 different alarm events detailing when the alarm state occurred, as well as when the unit returned within range. Alarm state indicator include audio alerts and flashing LCD segments.

Transfer data recorded in a CSV format to any computer via a USB flash drive no software is required. Unit continues to record data while downloading data. Sampling rate is 5 sec (10 sec for models 98768-55, -56, -59, and -60). Select logging interval ranging from 1 min to 24 hours. Other status indicators include low-battery, memory full, USB data transfer, and active alarm state. Probe is attached to a 10-ft (3 m) microcable that permits a door to close on it. Mount meter with included Velcro™ strips, wall-mount slots, or use flip-open stand on benchtop.

Select from glycol-filled glass, or vaccine bottle probe(s), standard plastic Bullet™ probe(s), or stainless steel probe(s). Bottle probes contain nontoxic glycol solution which is considered GRAS (generally recognized as safe) by the FDA. The solution filled bottle simulates the temperature of other stored liquids and eliminates the rapid temperature fluctuation caused by opening the refrigerator/freezer door. Vaccine bottles are designed to fit vaccine trays. Use standard Bullet probe to measure air and liquid temperatures. Bullet probe sensor and cable may be completely immersed; sensor measures 3/4"L x 0.187" dia (19 x 4.75 mm). Durable stainless steel probes measure 6-1/4"L x 0.125" dia (159 x 3.18 mm) and withstand both low and high temperatures ideal for measuring temperatures of air, liquids, and semi-solids.

Thermometer comes with a bottle probe filled with nontoxic glycol, eliminating the possibility of contamination from mercury. Solution is GRAS (generally recognized as safe) by the FDA.

Key Features

• Get accurate, reliable measurements with included NIST-traceable calibration
• Store up to 10 unique alarm events, memory can be cleared after downloading data
• Smart-Alarm™ with visual/audible alarm continues to alert even if the unit returns to nonalarm conditions
• Triple-display shows high, low, and current temperature simultaneously
• Temperature-buffered glycol bottle probe mimics solution

Includes

NIST-Traceable calibration certificate with data, bottle probe with 10-ft cable, magnetic strips, Velcro® strips, flip-open stand, and batteries.

TK9950-Z EndPoint ID Orthophosphate Test Kit, 10-100 ppm as PO4 by AquaPhoenix

In boiler water treatment, orthophosphate is primarily added to control scaling as it reacts with calcium hardness. Orthophosphate also works well has a corrosion inhibitor. Our EndPoint ID test kit includes filtering equipment, which is recommended before testing. Each kit is packaged in a durable plastic case and includes all items to complete approximately 60 tests.

EndPoint ID Test Kits Feature:

• Photographic instructions to simplify testing
• Quick reference safety and testing icons for best practices
• Waterproof and chemical-resistant instructions
• Private-labeled reagent labels and test kit box

3010KA Conductivity Meter Kit by Jenco

Includes:

• 3010 Conductivity Meter
• 107A: Conductivity Probe, Glass, K=10, 3-ft

Part Number: 66L-99-200

Part Number: 58L-402E

Part Number: 34L-490T