Sample Extraction Kit

Conf. with 3900000 (Extract), I00654B (Diluent 12/box) and 2 x 1005101 (Ampule Meth 10mL 6/box)

Conf. with 3900000 (Extract), I00623B (Diluent 12/box) and 2 x 1005105 (Ampule Meth 20mL 6/box)

7085000 EnSys RDX Explosives Soil Test Kit with Extraction Jars by Modern Water

Ensys® explosives kits are rapid field or laboratory colourimetric tests for the analysis of explosives in soil. The kits are based on a method developed by Dr. Thomas Jenkins at the US Army Corps of Engineers - CRREL.

Features:

• Detects RDX, HMX and related explosives
• Convenient and rapid testing in the field or laboratory
• Extractions can be performed simultaneously with analysis in singlicate
• Can test sample extract from EnSys TNT test
• Training recommended
• EPA SW-846 Method #8510 (proposed status final with 4th update)

Test result type

• Quantitative data

Samples per kit

• 20 soil samples

Assay range

• Soil: 1 ppm to 30 ppm total RDX
• Higher sample concentrations can be quantified by sample extract dilution

Sample preparation

• Soil samples require prior extraction using the included extraction components
• Soil samples should be dried prior to analysis
• Soil sample extracts from TNT soil test kit may be used

Sampling time

• 'Dirt-to-Data' in approximately 30 minutes
• Typically about six samples can be run in about one hour
• Soil extraction time is typically 2 - 10 minutes per sample plus test run time of approximately 20 minutes

Specificity

The Ensys® RDX test is specific for RDX, HMX and related explosive compounds and exhibits the following sensitivities. The RDX does not measure TNT, TNB or DNB.

Basic Test Procedure

• Clean cuvettes and set spectrophotometer
• Extract soil sample: Weigh 10 grams of soil sample, Add sample to extraction jar, Measure 50mL acetone into 50mL tube, Pour acetone into extraction jar and shake for three minutes, Allow to settle for five minutes
• Draw into syringe 5.5mL liquid from above the sediment layer in extraction jar
• Attach filter tip to syringe and transfer 5mL of sample extract into a 13mL tube
• NOTE: if nitrate/ nitrate interferents are present, attach an Alumina-A cartridge to the syringe and dispense through this
• Cut open an acetic acid bulb and add contents to the 13mL tube. Cap and shake
• Cut open a NitriVer pillow and add it to a 50mL reaction vial containing water
• Quickly pour acetic acid and sample into 13 mL zinc tube and cap. Invert twice and expose sample to zinc for EXACTLY 15 seconds
• With the filter attached to syringe and plunger removed, hold over reaction vial and pour zinc solution into it
• Rapidly filter the solution into the 50mL reaction vial, cap and shake for 30 seconds
• Incubate for 15 minutes for colour development and transfer contents to 30mL syringe barrel. Attach syringe filter and dispense into spectrophotometer cuvette
• Place cuvette in spectrophotometer and record absorbance
• Calculate results

Test kit components

• 20 weigh boats and wooden spatulas
• 20 extraction jars
• One 50mL graduated tube
• 20 - 50mL reaction vials with H2O
• 20 - 13mL zinc tube in foil pouches
• 20 - 10cc, 20cc and 30cc syringes
• 20 - 30mL tubes
• 20 NitriVer pillows
• 20 acetic acid bulb pipettes
• 60 syringe filters
• 1 bulb pipette
• 1 RDX control vial and ampoule cracker
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging.
• Store kits at room temperature (less than 80°F (27°C))
• Operate the test at temperature greater than 40°F/4°C and less than 100°F/39°C
• Do not expose the kits to direct sunlight

Required test materials

• EnSys RDX explosivessoil test kit (7085000)
• EnSys TNT explosives soil test kit (7002000)

Required test equipment

• Acetone: hardware or laboratory grade (min 50mL per sample)
• Alumina-A cartidges (if nitrate/nitrate interferents present) (6021200)

Other recommended materials

• Scissors
• Tap or laboratory grade water for cuvette rinsing
• Hach DR/2000, DR/2010 or DR/2800
• 2 matched hach cuvettes
• 2 cuvette stopper plugs
• Balance
• Marker pen, calculator
• Absorbent paper
• Liquid waste container
• PPE: Disposable gloves, eyewear

7310000 EnviroGard DDT Soil Kit by Modern Water

Envirogard® is a rapid field enzyme immunoassay method for the analysis of soil remediation, assessment and industrial testing. It uses a coated tube technology to detect the analyte of concern.

Features:

• Rapid and simple field testing procedures
• Semi-quantitative data results at set calibrator (action) levels
• Test up to 17 samples at once for increased cost efficiency
• Results available in less than 30 minutes
• Coated tube immunoassay
• EPA SW-846 Method #4042

Test result type

• Semi-quantitative or qualitative data

Samples per kit

• Up to 17 soil sample test results can be obtained per kit, depending upon the number of runs and action levels used.
• Typical applications use two or three calibrators and one negative control.

Assay range

• Semi-quantitative results (greater or less than) at calibrator (action) levels of 0.2, 1.0 and 10.0 ppm DDT
• Minimum detection level (MDL) is 0.2 ppm DDT.
• No maximum screening level as extracts can be diluted into test range

Sample preparation

• Soil samples require prior extraction using the MWI Sample Extraction Kit (sold separately).
• The Sample Extraction Kit provides material for 12 soil sample extractions with methanol.

Sampling time

• Soil extraction time is typically 2 minutes per sample plus assay run time of approximately 30 minutes.

Specificity

The EnviroGard DDT immunoassay test does not differentiate between DDT and other organochlorines. The table below shows compounds at the minimum detection limit (MDL) -an approximate concentration required to yield a positive result atthe lowest standard. The IC50 is the concentration required to inhibit one half of the color produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Basic Test Procedure

• Extract the soil sample using the MWI Sample Extraction Kit
• Pipet DDT assay diluent into the antibody coated tubes, then add either DDT calibrator or sample extract to the tubes along with DDT enzyme conjugate.
• Wait 15 minutes, then decant and wash the tubes.
• Add substrate.
• Wait for 10 minutes, add stop solution
• Read the absorbance using a photometer, and interpret the results. (Refer to DDT Soil Test Kit Instruction Guide procedures.)

Test kit components

• 20 antibody coated tubes
• Enzyme conjugate, colour developing and colour stop solution reagents
• Calibrators for 0.2, 1.0 and 10.0 ppm DDT.
• Negative control calibrator
• Test tube rack and pipet tips.
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Components must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight
• Portable spectrophotometer battery should be charged prior to use

Required test materials

• EnviroGard® DDT Soil Kit (7310000)
• Sample extraction kit (soil)(7310000EB)

Required test equipment

• Field soil lab (Accessory kit) (6050400) which includes: Repeating pipette*, Adjustable pipette*, Balance*, Repeating pipette tips*, Timer*
• Differential spectrophotometer - 110V (6000001), 220V (6000002)
• Field lab system rental (includes items marked with * above) (6997020)

Other recommended materials

• Latex gloves
• Absorbent paper for blotting test tubes
• Liquid and solid waste containers
• Calculator

7020301 PCB EnviroGard 12T Soil Test Kit by Modern Water

Envirogard® is a rapid field enzyme immunoassay method for the analysis of soil remediation, assessment and industrial testing. It uses a coated tube technology to detect the analyte of concern.

Features:

• Convenient and rapid testing in the field or labatory
• Tests up to 10 samples at once
• Two detection levels of your choice are provided with each sample
• High level of accuracy
• EPA SW-846 Method #4020

Test result type

• Semi-quantitative or qualitative data
• Knowledge of specific aroclor(s) present will aid accuracy

Samples per kit

• Dependent on batch size and number of detection levels
• Each sample can be tested one at a time or in batches of two to ten samples

Assay range

• Soil: 0.5 ppm to 500 ppm with dilutions
• Wipes: 5.0 ug/100cm² to 5000 ug/100cm² with dilutions

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately)
• The sample extraction kit provides materials for 12 soil sample extractions with methanol

Sampling time

• Approximately two minutes per sample plus assay run time of approximately 30 minutes

Basic Test Procedure

• Transfer soil or wipe to extraction jar
• Cap and shake for one minute
• Filter extracted sample
• Pipette and dilute samples with dilution ampule
• Transfer 1 ml of buffer to glass buffer tubes
• Pipette and transfer sample to buffer tubes
• Fit antibody coated tubes on buffer tubes; invert and mix;return to antibody coated tube
• Incubate for 10 minutes
• Connect antibody coated and conjugate tubes; invert and mix, return to antibody coated tube
• Incubate five minutes
• Wash antibody coated tubes vigorously four times
• Using a repeater pipette at setting two and 5 mL tip,transfer 200 uL substrateA to each tube
• Add 200 uL substrate B to each tube and mix
• Inclubate for 2.5 minutes
• Add 200 uL STOP to each tube
• Read tubes in photometer.Record data

Test kit components

• 48 antibody coated tubes and PCB enzyme conjugate vials
• 48 glass buffer tubes
• Substrate and stop solution reagents
• PCB standard
• Pipette tips and bulb pipettes
• Buffer
• Amber vials
• Wash solution
• 12 ampule crackers

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging.
• Store at ambient temperature 64° to 81°F (18° to 27°C)
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not freeze test kit components

Required test materials

• PCB EnviroGard 12T accessory kit (6050400)
• PCB EnviroGard 12T accessory kit rental (Includes all equipment required to operate test and interpret results)(6997020)

Required test equipment

• PCB EnviroGard 12T soil test kit (7020301)
• PCB soil sample extraction kit (7020301EB)
• EnviroGard PCB wipe sample extraction kit (7020301WA)

Other recommended materials

• Absorbent paper
• Liquid waste container
• Disposable gloves
• Marker pen
• Liquid and solid waste containers

A00134 RaPID Assay PCBs 100 Tube Kit by Modern Water

RaPID Assay® is a rapid field or laboratory enzyme immunoassay method for the analysis of soil and water for remediation, assessment, and industrial testing.

Features:

• Rapid field testing procedure for analysis of soil and water samples
• Quantitative data results with excellent analytical precision
• Results available in approximately 60 minutes
• Training available
• Magnetic particle immunoassay
• EPA SW-846 method #4020

Test result type

• Quantitative, semi-quantitative or qualitative

Samples per kit

• 100 test kit (tests up to 80+ samples)

Assay range

• Soil: 0.5 ppm to 10 ppm total PCB's as Aroclor 1254
• Water: 0.25 to 5.0 ppb total PCB s as Aroclor 1254
• Wipes: 5 to 100μg per wipe total PCB s as Aroclor 1254
• Range can be extended with additional dilutions

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately).
• The sample extraction kit provides materials for 12 soil sample extractions with methanol.
• Water samples must be diluted one part sample to one part methanol to prevent adsorptive loss.

Sampling time

• Soil extraction time is typically two minutes per sample plus assay run time of approximately 60 minutes

Specificity

The table below shows compounds at the method detection limit(MDL) which isthe lowest concentration of the compound that can be picked up in the assay. The limit of quantification (LOQ)- an approximate concentration required to yield a positive result at the lowest standard. The IC50 is the concentration required to inhibit one-half of the colour produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Basic Test Procedure

• Add calibrators and sample, enzyme conjugate, and antibody coupled magnetic particles to a test tube. Vortex.
• Incubate for 15 minutes
• Using the RaPID magnetic separator, decant and wash two times
• Add colour solution and incubate for 20 minutes
• Stop the reaction and read colour at 450 nm
• Quantitive results and QC parameters are calculated and printed automatically using the RPA spectrophotometer

Test kit components

• Antibody coated magnetic particles for analysis of 100 test tubes
• Zero standard, wash, enzyme conjugate, colour development and stop reagents
• Standards for 0.25, 1.00 and 5.0 ppb as Aroclor 1254
• Kit control as 3.0 ppb as Aroclor 1254
• Disposable test tubes
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• PCB Assay 100 tube kit (A00134)
• Sample extraction kit(for soil samples only) (A00137EB)
• Sample extraction kit(for wipe samples only) (A00137WB)
• PCB sample diluent 100mL (A00136)

Required test equipment

• RaPID Assay accessory kit which contains (6050100 (P)/6997010 (R)): RPA-I1 RaPID analyser (6000081), Printer (6000082), Magnetic separation rack (A00004), Repeator pipet (A00008), Adjustable volume pipet (A00176), Vortex mixer (A00014), Portable balance (A00131), Digital timer (A00015)
• Repeator pipet tips(12.5 mL) (A00009)
• Adjustable pipet tips (A00013)

Other recommended materials

• Latex gloves
• Liquid and solid waste containers
• Calculator
• Absorbant paper for blotting
• Marking pen

A00111 RaPID Assay Pentachlorophenol (PCP) 100 Tube Test Kit by Modern Water

RaPID Assay® is a rapid field or laboratory enzyme immunoassay method for the analysis of soil and water for remediation, assessment, and industrial testing.

Features:

• Rapid field testing procedure for analysis of soil and water samples
• Quantitative data results with excellent analytical precision
• Tests up to 50 samples at once
• Results available in approximately 60 minutes
• Magnetic particle immunoassay
• Training available
• EPA SW-846 method #4010

Test result type

• Quantitative, semi-quantitative or qualitative

Samples per kit

• 100 test kit (tests up to 80 samples)

Assay range

• Soil: 0.1 ppm to 10 ppm as pentachlorophenol
• Water: 0.1 to 10.0 ppb as pentachlorophenol
• Other applications are also available
• Range can be extended with additional dilutions

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately).
• The sample extraction kit provides materials for 12 soil sample extractions with alkaline methanol.

Sampling time

• Soil extraction time is typically two minutes per sample plus assay run time of approximately 60 minutes.

Specificity

The PCP RaPID Assay® immunoassay test does not differentiate between PCP and other organochlorines. The table below shows compounds at the limit of quantitation (LOQ)- an approximate concentration required to yield a positive result at the lowest standard. The IC50 isthe concentration required to inhibit one-half of the colour produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Basic Test Procedure

• Add prepared sample, enzyme conjugate, and antibody coupled magnetic particles.Vortex
• Incubate for 30 minutes
• Separate using the RaPID magnetic separator. decant and wash
• Add colour solution and incubate for 20 minutes
• Stop the reaction and read colour at 450 nm
• Quantitive results and QC parameters are calculated and printed automatically using the RPA-1I spectrophotometer

Test kit components

• Antibody coated magnetic particles for analysis of 100 test tubes
• Zero standard, wash, enzyme conjugate, colour development and stop reagents
• Standards for 0.1, 2 and 10 ppb as PCP
• Kit control as 1.0 ppb as PCP
• Disposable test tubes
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) for up to eight hours
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight
• Portable spectrophotometer battery should be charged prior to use

Required test materials

• PCP 100 tube test kit (A00111)
• Sample extraction kit (A00128EA)
• PCP sample diluent(as needed) (A00113)

Required test equipment

• RaPID Assay accessory kit which contains (6050100 (P)/6997010 (R)): RPA-I1 RaPID analyser (6000111), Magnetic separation rack (A00004), Repeator pipet (A00008), Adjustable volume pipet (A00176), Vortex mixer (A00014), Portable balance (A00131), Digital timer (A00015)
• Repeator pipet tips (A00009)
• Adjustable pipet tips (A00013)

Other recommended materials

• Latex gloves
• Liquid and solid waste containers
• Calculator
• Absorbant paper for blotting
• Marking pen

A00157 RaPID Assay PAHs 100 Test Tube Kit by Modern Water

RaPID Assay® is a rapid field or laboratory enzyme immunoassay method for the analysis of soil and water for remediation, assessment, and industrial testing.

Features:

• Rapid field testing procedure for analysis of soil and water samples
• Quantitative data results with excellent analytical precision
• Results available in approximately 60 minutes
• Tests up to 50 samples at once
• Magnetic particle immunoassay
• Training available
• EPA SW-846 method #4035

Test result type

• Quantitative, semi-quantitative or qualitative

Samples per kit

• 100 test kit (tests up to 80+ samples)

Assay range

• Soil: 0.2 ppm to 5 ppm as Phenanthrene
• Water: 2.66ppb to 66.5ppb as Phenanthrene
• Range can be extended with additional dilutions
• Site specific calibration required to meet total PAH analysis

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately).
• The sample extraction kit provides materials for 12 soil sample extractions
• Water samples must be diluted three parts sample to one part methanol to prevent adsorptive loss

Sampling time

• Soil extraction time is typically two minutes per sample plus assay run time of approximately 60 minutes

Specificity

The total PAHs (sum of 16 PAH compounds) of the indicated contaminant types in soil samples are expressed below, at each of the three kit calibrator (standards) levels, in units comparable to results from GC method 8270 or HPLC method 8310.

The RaPIDAssay® PAH immunoassay test does not differentiate between phenanthrene and other polyaromatic hydrocarbons.The table below shows compounds at the limit of quantitation (LOQ) - an approximate concentration required to yield a positive result at the lowest standard.The IC50 is the concentration required to inhibit one-half of the colour produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Test kit components

• Antibody coated magnetic particles for analysis of 100 test tubes
• Diluent zero, wash, enzyme conjugate, colour development, stop reagents and wash solution
• Standards for 2, 10 and 50 ppb as Phenanthrene
• Kit control as 25 ppb as Phenanthrene
• Disposable test tubes
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• PAH 100 test tube kit (A00157)
• Sample extraction kit(for soil samples only) (A00160EA)

Required test equipment

• RaPID Assay accessory kit which contains (6050100 (P)/6997010 (R)): RPA-II RaPID analyser (6000081), Printer (6000082), Magnetic separation rack (A00004C), Repeator pipet (A00008), Adjustable volume pipet (A00176), Vortex mixer (A00014), Portable balance (A00131), Digital timer (A00015)
• Repeator pipet tips (A00009)
• Adjustable pipet tips (A00013)

Other recommended materials

• Latex gloves
• Liquid and solid waste containers
• Calculator
• Absorbant paper for blotting
• Marking pen

A00205 RaPID Assay Carcinogenic PAHs (CPAH) 100 Tube Kit by Modern Water

RaPID Assay® is a rapid field or laboratory enzyme immunoassay method for the analysis of soil and water for remediation, assessment, and industrial testing.

Features:

• Rapid field testing procedure for analysis of soil and water samples
• Quantitative data results with excellent analytical precision
• Test up to 50 samples at one time
• Results available in approximately 60 minutes
• Training available
• Magnetic particle immunoassay
• EPA SW-846 method #4035 with increased sensitivity to carcinogenic PAHs

Test result type

• Quantitative, semi-quantitative or qualitative

Samples per kit

• 100 test kit (tests up to 80+ samples)

Assay range

• Soil: 10 ppb to 500 ppb as Benzo(a)pyrene
• Water: 0.1 to 5.0 ppb as Benzo(a)pyrene
• Range can be extended with additional dilutions
• Site specific calibration required to meet total PAH/C-PAH analysis requirements

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately).
• The sample extraction kit provides materials for 12 soil sample extractions with methanol.
• Water samples must be diluted with an equal volume of methanol to prevent adsorptive loss.

Sampling time

• Soil extraction time is typically two minutes per sample plus assay run time of approximately 60 minutes

Specificity

The total Carcinogenic PAH concentrations (sum of seven Carcinogenic PAH compounds) of the indicated contaminant types in soil samples are expressed below, at each of the three kit calibrator levels, in units comparable to results from GC method 8015 (TPH).

The RaPID assay Carcinogenic PAH immunoassay test does not differentiate between benzo(a)pyrene and other polyaromatic hydrocarbons. The table below shows compounds at the limit of quantitation (LOQ)- an approximate concentration required to yield a positive result at the lowest standard. The IC50 is the concentration required to inhibit one-half of the colour produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Test kit components

• Antibody coated magnetic particles, enzyme conjugate, colour development and stop and wash solutions for analysis of 100 test tubes
• Standards for 0.1, 1.0 and 5.0 ppb as Benzo(a) pyrene
• Kit control as 2.0 ppb as Benzo(a)pyrene
• Disposable test tubes
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• CPAH 100 tube kit (A00205)
• Sample extraction kit(for soil samples only) (A00204EA)
• cPAH sample diluent (100 mL) (A00203)

Required test equipment

• RaPID Assay accessory kit which contains (6050100 (P)/6997010 (R)): RPA-II analyser (6000081), Printer (6000082), Magnetic separation rack (A00004), Repeator pipet (A00008), Adjustable volume pipet (A00176), Vortex mixer (A00014), Portable balance (A00131), Digital timer (A00015)
• Repeator pipet tips(12.5 mL) (A00009)
• Adjustable pipet tips (A00013)

Other recommended materials

• Latex gloves
• Liquid and solid waste containers
• Calculator
• Absorbant paper for blotting
• Marking pen

A00162 RaPID Assay Total BTEX / TPH 100 Tube Kit by Modern Water

RaPID Assay® is a rapid field or laboratory enzyme immunoassay method for the analysis of soil and water for remediation, assessment, and industrial testing.

Features:

• Rapid field testing procedure for analysis of soil and water samples
• Quantitative data results with excellent analytical precision
• Results available in approximately 60 minutes
• Training available
• Magnetic particle immunoassay
• Correlated to TPH methods (knowledge of fuel source required)

Test result type

• Quantitative, semi-quantitative or qualitative

Samples per kit

• 100 test kit (tests up to 80+ samples) (Five kit minimum order)

Assay range

• Soil: 0.9 ppm to 30 ppm as total BTEX standard
• Water: 0.02 to 3.0 ppm as total BTEX standard
• asTPH:range varies based on fuel source

Sample preparation

• Soil samples require prior extraction using the sample extraction kit (sold separately).
• The sample extraction kit provides materials for 12 soil sample extractions with methanol.

Sampling time

• Soil extraction time is typically two minutes per sample plus assay run time of approximately 60 minutes.

Specificity

The total BTEX/TPH concentrations of the indicated contaminant types in soil samples are expressed below, at each ofthe three kit calibrator levels, in units comparable to results from GC method 8015 (TPH).

The total BTEX/ TPH RaPID assay immunoassay test does not differentiate between BTEX and other petroleum hydrocarbons.The table below shows compounds at the limit of quantitation (LOQ) - an approximate concentration required to yield a positive result at the lowest standard. The IC50 is the concentration required to inhibit one-half of the colour produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Test kit components

• Antibody coated magnetic particles for analysis of 100 test tubes
• Zero standard, wash, enzyme conjugate, colour development and stop reagents
• Standards for 0.09, 0.35 and 3.0 ppm as total BTEX
• Kit control as 2.1 ppm as total BTEX
• Disposable test tubes

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• Total BTEX/TPH 100 tube kit (A00162)
• Sample extraction kit(for soil samples only) (A00165EB)
• Total BTEX sample diluent 100ml (as needed to increase range)

Required test equipment

• RaPID Assay accessory kit which contains (6050100 (P)/6997010 (R)): RPA-II RaPID analyser (6000111), Magnetic separation rack (A00004), Repeator pipet (A00008), Adjustable volume pipet (A00176), Vortex mixer (A00014), Portable balance (A00131), Digital timer (A00015)
• Repeator pipet tips (A00009)
• Adjustable pipet tips (A00013)

Other recommended materials

• Latex gloves
• Liquid and solid waste containers
• Calculator
• Absorbant paper for blotting
• Marking pen

7002000 EnSys TNT Explosives Soil Test Kit by Modern Water

EnSys® explosives kits are rapid field or laboratory colourimetric tests for the analysis of explosives in soil. The kits are based on a method developed by Dr. Thomas Jenkins at the US Army Corps of Engineers - CRREL.

Features:

• Detects TNT, DNT and related explosives
• Convenient and rapid testing in the field or laboratory
• Extractions can be performed simultaneously with analysis in singlicate
• TNT extracts can be used with EnSys RDX test
• Training available
• EPA SW-846 Method #8515

Test result type

• Quantitative data

Samples per kit

• 20 soil samples

Assay range

• Soil: 1 ppm to 30 ppm total TNT
• Higher sample concentrations can be quantified by sample extract dilution

Sample preparation

• Soil samples require prior extraction using the included extraction components
• Soil samples should be dried prior to analysis
• Soil sample extracts may be saved for use with the RDXsoil test kit

Sampling time

• 'Dirt-to-Data' in approximately 30 minutes
• Typically about ten samples can be run in about 40 minutes
• Soil extraction time is typically 2 - 10 minutes per sample plus test run time of approximately 2 minutes

Specificity

The EnSys® TNT test is specific for TNT and related explosive compounds and exhibits the following sensitivities. The TNT test does not measure RDX or HMX.

Basic Test Procedure

• Clean cuvettes and set spectrophotometer
• Extract soil sample: Weigh 10 grams of soil sample, Add sample to extraction jar, Measure 50mL acetone into 50mL tube, Pour acetone into extraction jar and shake for three minutes, Allow to settle for five minutes
• Draw 25mL liquid into the syringe from above the sediment layer in extraction jar
• Attach filter tip to syringe and transfer 25mL of sample extract into a cuvette.
• Place cuvette in spectrophotometer and record initial absorbance
• Add one drop of developer solution, cap and shake for three seconds.
• Remove stopper and place the'sample' cuvette in cell holder and read sample absorbance.
• NOTE: For analysis of samples containing DNT,and/or where DNT concentration is of concern, samples must be allowed to develop for 10 minutes before reading sample absorbance. This will not affect colour development for other nitroaromatics.
• Record data and calculate results.

Test kit components

• 20 weigh boats and wooden spatulas
• 20 extraction jars
• One 50mL graduated tube
• 20 - 30cc syringes and syringe filters
• 1 bulb pipette
• 1 TNT control vial and ampoule cracker
• Developer solution
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging.
• Store at ambient temperature 64° to 81°F (18° to 27°C)
• Operate the test at temperature greater than 40°F/4°C and less than 100°F/39°C (4°C)

Required test materials

• EnSys TNT explosives soil test kit (7002000)

Required test equipment

• EnSys TNT accessory kit (rental, includes HACH DR2800) (6999700)
• Acetone: hardware or laboratory grade (min 50mL per sample)

Other recommended materials

• Hach DR/2000, DR/2010 or DR/2800
• 2 matched hach cuvettes
• 2 cuvette stopper plugs
• Balance
• Tap or laboratory grade water for cuvette rinsing
• Marker pen, calculator
• Absorbent paper
• Liquid waste container
• PPE: Disposable gloves, eyewear

A00082 2, 4-D 100 Tube Kit by Modern Water

RaPID Assay® is a rapid field or laboratory enzyme immunoassay method for the analysis of soil and water for remediation, assessment, and industrial testing.

Features:

• Rapid field testing procedure for analysis of soil and water samples
• Quantitative data results with excellent analytical precision
• Test up to 50 samples at one time
• Results available in approximately 60 minutes
• Training available
• Magnetic particle immunoassay
• EPA SW-846 method #4015

Test result type

• Quantitative, semi-quantitative or qualitative

Samples per kit

• 100 test kit (tests up to 80+ samples)

Assay range

• Soil: 0.15 ppm to 7.5 ppm as 2, 4-D
• Water: 1.0 to 50.0 ppb as 2, 4-D
• Range can be extended with additional dilutions

Sample preparation

• Soil samples require prior extraction as indicated in the application procedure

Sampling time

• A 16 hour extraction time is recommended for soil Method 4015

Specificity

The 2, 4D RaPID Assay immunoassay test does not differentiate between 2,4-D and other chlorophenoxy acids. The table below shows compounds at the limit of quantitation (LOQ) -an approximate concentration required to yield a positive result at the lowest standard. The IC50 is the concentration required to inhibit one-half of the color produced by the negative control. It is also used to calculate cross-reactivity values to similar compounds.

Basic Test Procedure

• Add standards, prepared sample, enzyme conjugate, and antibody coupled magnetic particles.Vortex.
• Incubate for 30 minutes
• Using the magnetic separator, decant and wash
• Add colour solution, incubate 20 minutes
• Stop the reaction and read colour at 450 nm
• Quantitative results and QC parameters are calculated and printed automatically using the RPA-1I spectrophotometer

Test kit components

• Antibody coated magnetic particles for analysis of 100 test tubes
• Zero standard, wash, enzyme conjugate, colour development and stop reagents
• Standards for 1, 10 and 50 ppb as 2, 4-D
• Disposable test tubes
• Test kit instructions

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use for up to 8 hours
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• 2, 4-D 100 tube kit (A00082)
• 2, 4-D sample diluent (A00079)

Required test equipment

• RaPID Assay accessory kit (6050100 (P)/6997010 (R)) which contains: RPAI1 analyser (6000081), Magnetic separation rack (A00004), Repeator pipet (A00008), Adjustable volume pipet (A00176), Vortex mixer (A00014), Portable balance (A00131), Digital timer (A00015)
• Repeator pipet tips (12.5 mL) (A00013)
• Adjustable pipet tips

Other recommended materials

• Latex gloves
• Liquid and solid waste containers
• Calculator
• Absorbant paper for blotting
• Marking pen

7540000 EnviroGard Microcystins Plate Kit by Modern Water

Envirogard® is a rapid laboratory enzyme immunoassay method for the analysis of water. It uses a plate technology to detect the analyte of concern.

Features:

• Rapid lab testing method for the detection of microcystins and nodularins in drinking and environmental water samples
• Conforms to ISO standards for environmental immunoassays such as ISO 15089
• Quantiative data results with excellent analytical precision
• Test up to 88 samples* at once for increased cost efficiency
• Results available in approximately 120 minutes
• Microtiter plate immunoassay
• Ideal for source water monitoring

Test result type

• Quantitative data

Samples per kit

• 96 well test kit (tests up to 88 samples*)

Assay range

• 0.1 ppb to 1.6 ppb
• Extended range available

Sampling time

• Sample-to-data in approximately 120 minutes

Specificity

The proprietary antibody used in this assay detects microcystins and nodularins. The crossreactivity of the Microcycstins EnviroGard® Plate Kit for various microcystin variants is shown below at 50% B/B₀

Basic Test Procedure

• Prepare standards
• Add 100 uL of sample or standard
• Incubate for 30 minutes
• Add 100 uL enzyme conjugate
• Incubate for 30 minutes
• Decant and wash five times
• Add 100 uL colour solution
• Incubate for 30 minutes
• Stop the reaction and read colour at 450nm

Test kit components

• Antibody coated microtiter plate strips, enzyme conjugate, colour development and stop reagent for analysis of 96 wells
• One vial each of 0.1, 0.2, 0.4, 0.56, 0.8 and 1.6 ppb microcystin-LR surrogate (nontoxic) calibrators
• Test kit instructions
• Optional 1.5 ppb check standard

Storage & precautions

• Shelf life is typically one year from date of manufacture, with specific kit expiration date information provided on product packaging
• Reagents must be stored at 39° to 46°F (4° to 8°C) when not in use
• Store at ambient temperature 64° to 81°F (18° to 27°C) is acceptable for day of use for up to eight hours
• Kits must be brought to 64° to 81°F (18° to 27°C) before use
• Do not expose colour solution to direct sunlight

Required test materials

• Microcystins EnviroGard® plate (7540000)

Required test equipment

• 10 cc syringes
• 0.45 micron non-sterile filter units
• Pipette to deliver 100 mL
• Distilled or DI water for rinsing wells
• Microtiter plate reder or stip reader
• Timer
• Parafilm or tape
• Marker pen

Other recommended materials

• Orbital shaker
• Multi-channel pipette
• Repeater pipette
• Calculator
• Microtiter plate washer
• Solid extraction devices

MIDAS-K-B2H MIDAS Sensor Kit includes Transmitter, Sensor (Diborane (B2H6) - (36-400 ppb)) by Honeywell Analytics

Bringing new visibility, reliability and ease of use to gas detection in semiconductor processing and industrial manufacturing

Choose the MIDAS Gas Detector to detect more than 35 gases - easily, quickly and error-free. All with extended sensor calibration periods, patented diagnostics and lower cost of ownership.

The MIDAS Gas Detector uses reliable sensor technology to detect many key toxic, ambient and flammable gases in a plant. The device monitors points up to 100 feet (30 meters) away while using patented technology to regulate flow rates and ensure error-free gas detection. Thanks to Honeywell's use of advanced robotics, the MIDAS Gas Detector offers unbeatable quality and reliability:

• Improved visibility and ease of use. The MIDAS Gas Detector is equipped with bright LED lights and an intuitive, interactive interface that provides instant alerts to gas readings or alarm levels. The interface also includes passwordprotected menus for configuration, test and calibration.
• Easy installation. Compact in size with an easy-to-handle metal chassis, the MIDAS Gas Detector is simple to install. That s especially important in crowded, complex process environments where space is at a premium.
• A complete solution. The MIDAS Gas Detector is complemented by our innovative Chemcassette® technology, which detects ultrasensitive toxic gases at low parts-per-billion (ppb) levels. And we offer the support of a worldwide network of service engineers who operate on a 24/7 basis.
• Numerous applications. With feature-rich capabilities that are easy to use, the MIDAS Gas Detector is suitable for many industry applications, including semiconductor processing, light industrial manufacturing, university laboratories, aerospace, wastewater and more.

Features:

• Over 35 gases available with extended 2 year warranty
• Smart sensor cartridge with on board 'e-calibration' certificate
• 3 built in relays (Form C) for Alarm 1, 2 and Fault
• Power over Ethernet (PoE) communication
• Keypad interface and remote web browser interface
• Optional MIDAS Pyrolyzer module that connects to any MIDAS Gas Detector
• Password protected menu levels to preserve system integrity
• Bright LEDs and intuitive icon driven, large multicolor backlit LCD display
• Factory-calibrated sensors to reduce need for frequent gas testing
• Isolated 0-22 mA analog output with fault and event reporting
• Modbus/TCP Ethernet for easy connectivity to all control and alarm systems ports for control connectivity and service interaction
• Robust extractive pump system (2 year lifetime) sampling up to 100 feet
• CE marked for total immunity to Radio Frequency Interference
• Reflex® sensor health check for improved safety
• TempraSureTM temperature compensation technology as appropriate
• Event logging to review sensor history

Plug-and-play gas detection

With flexible features and options, the MIDAS Gas Detector works right out of the box and configures easily to meet your needs. Each plug-and-play sensor cartridge is pre-calibrated, so it's ready when you are. That means longer sensor life, quick and easy replacement, and no operator error due to incorrect or depleted sensors.

The standard power supply and communications capabilities include three onboard relays, 0-22 mA analog output and Modbus/TCP Ethernet digital outputs. Plus, the MIDAS Gas Detector includes the innovative Power over Ethernet (PoE) protocol - a single Ethernet connection for all power, control and communication requirements. Thanks to the MIDAS architecture, cost-effective integration with PLC and Fieldbus systems is greatly simplified.

MIDAS® Pyrolyzer

Offered as an option, the MIDAS Pyrolyzer allows for the detection of NF₃ and other CxFy gases. Cost of ownership is low, as the Pyrolyzer has a replaceable heater assembly with a lifespan of greater than two years. Even more, thanks to our new proprietary catalyst to improve efficiency in gas conversion, the Pyrolyzer delivers automatic flow control, temperature control, and fast and accurate performance. Additionally, the Pyrolyzer can run from a MIDAS Gas Detector that s powered by either PoE or 24 VDC.

MIDAS-K-CFX MIDAS Sensor Kit includes Transmitter, (Difluoromethane (CH2F2) - (6-120 ppm)) by Honeywell Analytics

Bringing new visibility, reliability and ease of use to gas detection in semiconductor processing and industrial manufacturing

Choose the MIDAS Gas Detector to detect more than 35 gases - easily, quickly and error-free. All with extended sensor calibration periods, patented diagnostics and lower cost of ownership.

The MIDAS Gas Detector uses reliable sensor technology to detect many key toxic, ambient and flammable gases in a plant. The device monitors points up to 100 feet (30 meters) away while using patented technology to regulate flow rates and ensure error-free gas detection. Thanks to Honeywell's use of advanced robotics, the MIDAS Gas Detector offers unbeatable quality and reliability:

• Improved visibility and ease of use. The MIDAS Gas Detector is equipped with bright LED lights and an intuitive, interactive interface that provides instant alerts to gas readings or alarm levels. The interface also includes passwordprotected menus for configuration, test and calibration.
• Easy installation. Compact in size with an easy-to-handle metal chassis, the MIDAS Gas Detector is simple to install. That s especially important in crowded, complex process environments where space is at a premium.
• A complete solution. The MIDAS Gas Detector is complemented by our innovative Chemcassette® technology, which detects ultrasensitive toxic gases at low parts-per-billion (ppb) levels. And we offer the support of a worldwide network of service engineers who operate on a 24/7 basis.
• Numerous applications. With feature-rich capabilities that are easy to use, the MIDAS Gas Detector is suitable for many industry applications, including semiconductor processing, light industrial manufacturing, university laboratories, aerospace, wastewater and more.

Features:

• Over 35 gases available with extended 2 year warranty
• Smart sensor cartridge with on board 'e-calibration' certificate
• 3 built in relays (Form C) for Alarm 1, 2 and Fault
• Power over Ethernet (PoE) communication
• Keypad interface and remote web browser interface
• Optional MIDAS Pyrolyzer module that connects to any MIDAS Gas Detector
• Password protected menu levels to preserve system integrity
• Bright LEDs and intuitive icon driven, large multicolor backlit LCD display
• Factory-calibrated sensors to reduce need for frequent gas testing
• Isolated 0-22 mA analog output with fault and event reporting
• Modbus/TCP Ethernet for easy connectivity to all control and alarm systems ports for control connectivity and service interaction
• Robust extractive pump system (2 year lifetime) sampling up to 100 feet
• CE marked for total immunity to Radio Frequency Interference
• Reflex® sensor health check for improved safety
• TempraSureTM temperature compensation technology as appropriate
• Event logging to review sensor history

Plug-and-play gas detection

With flexible features and options, the MIDAS Gas Detector works right out of the box and configures easily to meet your needs. Each plug-and-play sensor cartridge is pre-calibrated, so it's ready when you are. That means longer sensor life, quick and easy replacement, and no operator error due to incorrect or depleted sensors.

The standard power supply and communications capabilities include three onboard relays, 0-22 mA analog output and Modbus/TCP Ethernet digital outputs. Plus, the MIDAS Gas Detector includes the innovative Power over Ethernet (PoE) protocol - a single Ethernet connection for all power, control and communication requirements. Thanks to the MIDAS architecture, cost-effective integration with PLC and Fieldbus systems is greatly simplified.

MIDAS® Pyrolyzer

Offered as an option, the MIDAS Pyrolyzer allows for the detection of NF₃ and other CxFy gases. Cost of ownership is low, as the Pyrolyzer has a replaceable heater assembly with a lifespan of greater than two years. Even more, thanks to our new proprietary catalyst to improve efficiency in gas conversion, the Pyrolyzer delivers automatic flow control, temperature control, and fast and accurate performance. Additionally, the Pyrolyzer can run from a MIDAS Gas Detector that s powered by either PoE or 24 VDC.

MIDAS-K-CO2 MIDAS Sensor Kit includes Transmitter, Sensor (Carbon Dioxide (CO2) - (0.15-2.0%)) by Honeywell Analytics

Bringing new visibility, reliability and ease of use to gas detection in semiconductor processing and industrial manufacturing

Choose the MIDAS Gas Detector to detect more than 35 gases - easily, quickly and error-free. All with extended sensor calibration periods, patented diagnostics and lower cost of ownership.

The MIDAS Gas Detector uses reliable sensor technology to detect many key toxic, ambient and flammable gases in a plant. The device monitors points up to 100 feet (30 meters) away while using patented technology to regulate flow rates and ensure error-free gas detection. Thanks to Honeywell's use of advanced robotics, the MIDAS Gas Detector offers unbeatable quality and reliability:

• Improved visibility and ease of use. The MIDAS Gas Detector is equipped with bright LED lights and an intuitive, interactive interface that provides instant alerts to gas readings or alarm levels. The interface also includes passwordprotected menus for configuration, test and calibration.
• Easy installation. Compact in size with an easy-to-handle metal chassis, the MIDAS Gas Detector is simple to install. That s especially important in crowded, complex process environments where space is at a premium.
• A complete solution. The MIDAS Gas Detector is complemented by our innovative Chemcassette® technology, which detects ultrasensitive toxic gases at low parts-per-billion (ppb) levels. And we offer the support of a worldwide network of service engineers who operate on a 24/7 basis.
• Numerous applications. With feature-rich capabilities that are easy to use, the MIDAS Gas Detector is suitable for many industry applications, including semiconductor processing, light industrial manufacturing, university laboratories, aerospace, wastewater and more.

Features:

• Over 35 gases available with extended 2 year warranty
• Smart sensor cartridge with on board 'e-calibration' certificate
• 3 built in relays (Form C) for Alarm 1, 2 and Fault
• Power over Ethernet (PoE) communication
• Keypad interface and remote web browser interface
• Optional MIDAS Pyrolyzer module that connects to any MIDAS Gas Detector
• Password protected menu levels to preserve system integrity
• Bright LEDs and intuitive icon driven, large multicolor backlit LCD display
• Factory-calibrated sensors to reduce need for frequent gas testing
• Isolated 0-22 mA analog output with fault and event reporting
• Modbus/TCP Ethernet for easy connectivity to all control and alarm systems ports for control connectivity and service interaction
• Robust extractive pump system (2 year lifetime) sampling up to 100 feet
• CE marked for total immunity to Radio Frequency Interference
• Reflex® sensor health check for improved safety
• TempraSureTM temperature compensation technology as appropriate
• Event logging to review sensor history

Plug-and-play gas detection

With flexible features and options, the MIDAS Gas Detector works right out of the box and configures easily to meet your needs. Each plug-and-play sensor cartridge is pre-calibrated, so it's ready when you are. That means longer sensor life, quick and easy replacement, and no operator error due to incorrect or depleted sensors.

The standard power supply and communications capabilities include three onboard relays, 0-22 mA analog output and Modbus/TCP Ethernet digital outputs. Plus, the MIDAS Gas Detector includes the innovative Power over Ethernet (PoE) protocol - a single Ethernet connection for all power, control and communication requirements. Thanks to the MIDAS architecture, cost-effective integration with PLC and Fieldbus systems is greatly simplified.

MIDAS® Pyrolyzer

Offered as an option, the MIDAS Pyrolyzer allows for the detection of NF₃ and other CxFy gases. Cost of ownership is low, as the Pyrolyzer has a replaceable heater assembly with a lifespan of greater than two years. Even more, thanks to our new proprietary catalyst to improve efficiency in gas conversion, the Pyrolyzer delivers automatic flow control, temperature control, and fast and accurate performance. Additionally, the Pyrolyzer can run from a MIDAS Gas Detector that s powered by either PoE or 24 VDC.