Ammonia Detector

2106B1806 Sensepoint Hazardous Area Approved Gas Detector, CO 0-200 ppm Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2106B1810 Sensepoint Hazardous Area Approved Gas Detector, Cl2 0-5 ppm Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2106B1813 Sensepoint Hazardous Area Approved Gas Detector, NH3 0-50 ppm Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2106B1816 Sensepoint Hazardous Area Approved Gas Detector, H2 0-1000 ppm Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2106B1818 Sensepoint Hazardous Area Approved Gas Detector, NO 0-100 ppm Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2106B1820 Sensepoint Hazardous Area Approved Gas Detector, SO2 0-15 ppm Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2106B1822 Sensepoint Hazardous Area Approved Gas Detector, NO2 0-10 ppm Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2106B1830 Sensepoint Hazardous Area Approved Gas Detector, 0-25 V/V O2 Toxic Sensor 3/4NPT CSA by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

M-600104 R22 Vent Line Sensor, Linear Pre-amp, with Mounting Kit by Honeywell Analytics

The Manning Vent Line sensor continuously monitors vent line headers for ammonia and fluorocarbons.

The Manning Vent Line (VL) is designed to continuously monitor for high concentrations of ammonia or fluorocarbons in vent lines of refrigeration systems.

High concentrations of refrigerant gases in vent lines are warnings of system overpressure or leaking relief valves. Either can pose danger to employees and equipment. Wasted refrigerants are costly and can mean overtime labor and plant downtime.

Designed to be installed in refrigeration vent lines, the VL sensor is supplied with a 2" cast steel "T", plug and nipple.

The sensor is embedded in a 2" forged steel bull plug and houses a four-point terminal strip for electrically connecting the sensor and preamp. The linear 4/20 mA output pre-amp is housed in a separate enclosure.

The Manning Vent Line leak detector is designed to be electrically connected to and monitored by all Honeywell Analytics readouts or can send a signal directly to a PLC.

Beneficial Features

• Improves personnel, product and equipment safety
• Extremely reliable sensor assembly
• Easy to calibrate and adjust
• Simple to install
• Continuous monitoring
• Can potentially lower insurance rates
• Input directly to central alarm systems
• Linear 4/20 mA output

Applications

• Ammonia or Fluorocarbon Monitoring of Refrigeration System Vent Lines
• Equipment Rooms
• Refrigeration Systems

D03-0009-000 RAEGuard 2 PID Transmitter Kit, UL, 0.01 - 100 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

D03-0010-000 RAEGuard 2 PID Transmitter Kit, UL, 0.1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

D03-0012-000 RAEGuard 2 PID Transmitter Kit, UL, 1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-03-0010-000 RAEGuard 2 PID Transmitter Kit, Range: 0.1 to 1000 ppm by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0001-000 RAEGuard 2 PID Diffusion Transmitter Kit, 0.01-100 PPM, FGM-2001, HONHON by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0002-000 RAEGuard 2 PID Diffusion Transmitter Kit, 0.1-1000 PPM, FGM-2002, HONHON by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0004-000 RAEGuard 2 PID Transmitter Kit, ATEX/IECEx, 0.01 - 100 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0005-000 RAEGuard 2 PID Transmitter Kit, ATEX/IECEx, 0.1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0008-000 RAEGuard 2 PID Transmitter Kit, ATEX/IECEx, 1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0009-000 RAEGuard 2 PID Transmitter Kit, UL, 0.01 - 100 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0010-000 RAEGuard 2 PID Transmitter Kit, UL, 0.1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0012-000 RAEGuard 2 PID Transmitter Kit, UL, 1 - 1000 ppm Isobutylene Equivalent by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0015-000 RAEGuard 2 PID Diffusion Transmitter Kit, 0.01-100 PPM, FGM-2001, UL, HONHON by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab

H-D03-0016-000 RAEGuard 2 PID Diffusion Transmitter Kit, 0.1-1000 PPM, FGM-2002, UL, HONHON by Honeywell Analytics

The RAEGuard 2 PID operates on 10 to 28 VDC and provides an analogue (4-20 mA) three-wire signal output, and RS-485 Modbus digital signal output. It is available in two different models, pumped or diffusion, to best fit your needs.

Calibration has been greatly simplified with the introduction of Electronic Auto-Zero patented by Honeywell.

The RAEGuard 2 PID is utilizing many of Honeywell's PID patents such as the Electronic Auto-Zero that guarantees an incomparable base line stability making it the best in class product.

Polynomial based calibration provides superior calibration linearity throughout the full range.

The RAEGuard 2 PID has a graphic display and LED light status indicator for fault and alarm conditions. In addition, low, high, and fault relays1 can be configured to trigger external alarms or process controls.

A magnetic key interface enables the detector to be calibrated and operational parameters adjusted with the explosion-proof enclosure in place.

MODEL OPTIONS: PUMPED OR DIFFUSION

• Pumped is used for sticky gas
• Diffusion is used for high humidity ambients

REDUCED MAINTENANCE COSTS

• Easy to remove sensor module in hazardous locations without use of tools

REDUCED LIFE COSTS

• Unique lamp design makes the product more robust and enables longer life time

AVAILABILITY

• Continuous VOC monitoring in hazardous and non-hazardous locations

PROVIDES FASTER RESPONSE TIMES

• The sample flow-through design powered by an internal diaphragm pump provides faster response times

ACCURATE READINGS

• Guaranteed by humidity compensation even in humid environments

ADVANCED TECHNOLOGY

• Patented pump duty cycle extending the sensor and lamp cleaning interval
• Patented Electronic Zero keeping the zero point stable
• Patented 3D sensor technology lower quenching effect - faster response to high concentration - lower RH response

SUITABLE FOR A WIDE RANGE OF APPLICATIONS

• Over 200 correction factors are pre-programmed and allow users to display readings of specific target gas

KEY APPLICATIONS AND THEIR VOCS

• Benzene in refinery analyser shelters
• Ammonia in industry
• Vinyl Chloride in chemical manufacturing
• Toluene or Ammonia in semi-conductor plants
• Solvent and chemicals storage
• Phenol and DME in pharmaceutical
• Toluene in printing
• Air quality
• Methyl Ethyl Ketone in paint spray booths
• Heat transfer fluids
• Acetone, Xylene, Phenol in medical, pathology, histology lab