$200 - $300, Test and Measurement, Test Products International

192 True RMS 50,000 count DMM with Inductance by Test Products International

The Triple Display 192 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 192 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The meter also has RS232 output and software for recording information into a PC.

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP: Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Data logging
• 50,000 count display
• 0.05% DCV basic accuracy
• Inductance, Frequency and Capacitance
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1
• CATIII-1000VC, CATIII-1000V, CAT IV-600V, CAT III 1000V
• True RMS DMM
• Time Stamp Logging
• Optional PC Output with A192
• Pulse Width
• Duty cycle (% pulse width modulation) for measuring modulating gas valves

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Motor start and run capacitance
• Frequency on controls and line voltages
• Record min/max voltage of controls and line voltages
• Temperature with optional temperature adapter (A310)
• Bar graph to indicate rapid fluctuations in measurements
• Voltage of direct drive DC motors
• Measure power supply voltage
• Match components
• Compare readings in circuits and components
• Frequency of line and control voltage

TPI-1200 BNC Attenuator Kit by Test Products International

Includes

• 805-53-000 BNC Shunt
• 120082 Individual BNC Attenuator, 3 dB 1.0 Watt
• 120083 Individual BNC Attenuator, 6 dB 1.0 Watt
• 120085 Individual BNC Attenuator, 20 dB 0.5 Watt
• 105-52-000 BNC Termination

120085 BNC Attenuator Kit by Test Products International

Features

• Increase the input range of an oscilloscope.
• Reduce the output level of fixed amplitude signal sources.
• Connect low impedance sources to instruments with high-impedance inputs.

Includes

• 120082 Individual BNC Attenuator, 3 dB 1.0 Watt
• 120083 Individual BNC Attenuator, 6 dB 1.0 Watt
• 120084 Individual BNC Attenuator, 10 dB 0.5 Watt
• 120085 Individual BNC Attenuator, 20 dB 0.5 Watt

194 True RMS 50,000 Count DMM with CAT IV, 1000V Rating with A106 and GK13M by Test Products International

The Triple Display 194 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 194 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The meter also has RS232 output and software for recording information into a PC

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP: Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Data logging
• 50,000 count display
• 0.05% DCV basic accuracy
• Inductance, Frequency and Capacitance
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1
• CATIII-1000VC, CATIII-1000V, CAT IV-600V, CAT III 1000V
• True RMS DMM
• Time Stamp Logging
• Optional PC Output with A192
• Pulse Width
• Duty cycle (% pulse width modulation) for measuring modulating gas valves

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Motor start and run capacitance
• Frequency on controls and line voltages
• Record min/max voltage of controls and line voltages
• Temperature with optional temperature adapter (A310)
• Bar graph to indicate rapid fluctuations in measurements
• Voltage of direct drive DC motors
• Measure power supply voltage
• Match components
• Compare readings in circuits and components
• Frequency of line and control voltage

196 Process Meter by Test Products International

The Triple Display 196 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 196 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The DMM 196 also has RS232 output and software for recording information into a PC.

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP:Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Large 50,000 count display: increases resolution and improves accuracy (1.7" x 2.75", 43mm x 70mm)
• 0-24mA output: t for process controls
• Triple Display: shows more than one reading simultaneously
• 51 Segment Analog Bar Graph: to catch fast AC fluctuations
• Logic Test: Indicates transitions up to 2 MHz.
• Frequency Counter: Measure low frequency signals from 1Hz to 2 MHz and display duty cycle, pulse width and period.
• Back Light (LED Type) allows viewing in any light condition
• Auto Range automatically selects the best range for the measurement
• Separate battery and fuse compartment for easy replacement
• Auto Power Off DMM will automatically power down after approximately 15 minutes of inactivity to extend battery life. Disable Auto Power Off: Hold down the REC button and turn the meter on
• Increased safety with Silicone rubber 1,000V CAT III, 600V CAT IV, 10A test leads (CE & cUL listed)
• Diode Test displays approximate forward bias voltage
• Process DMM with 0 to 24mA output
• 0.05% DCV basic accuracy
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1

Applications:

• View industrial signals such as motor control, UPS, switching power supplies, and PLC controls with 1MHz bandwidth
• Capture noise spikes, glitches, and intermittents with 20 megasamples per second sampling rate
• Full autoranging, True RMS, DMM capabilities
• Measure resistance and test for continuity
• Continually updated display provides a live presentation
• Water Purification
• Chemical Processing
• Oil & Gas
• Power Generation
• Pulp & Paper
• Food & Beverage

343C5 Dual Input K-Type Thermocouple Thermometer with Two GK13M Probes and Two CK24M Probes A901 Carrying Case by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Auto Field Calibrate in less than 10 seconds in ice water to achieve ± 1°F system (tester & probe) accuracy within 30°F to 120°F temperature range
• Temp1, Temp2, Temp1-Temp2 display modes
• Min / Max Record
• Auto Resolution (0.1° / 1°)
• °C/°F Selectable
• Hold feature freezes reading on display
• Auto Off
• Protective rubber boot
• Easy to read LCD display

Includes:

• Two GK13M temperature probe
• A908 Case
• Two CK21M pipe clamp probes

377BT Infrared Thermometers (IR) With Bluetooth Comunication by Test Products International

Thoroughly testing and diagnosing high efficiency HVACR systems or large surface areas can be labor intensive and expensive. Using the appropriate non-contact thermometer can reduce man hours and help insure system performance more easily, accurately and affordably.

Measure Hard-to-reach, sensitive, or large moving target areas. Use the 380, 381, and 383 to measure surface temperature and watch the LCD immediately display accurate data without the use of a probe.

Features:

• Bluetooth Communication
• Laser pointer
• Record function (Min/Max)
• Display data hold function
• Back light
• Trigger switch
• 8:1 distance to spot ratio
• °C and °F selectable
• Gun-type compact design
• Operating lock function
• 9V battery and soft pouch included

Appications:

• Heating & AC/R system measurements on all non-metallic and many metallic surfaces
• Troubleshootoverheating devices
• Vent air and return temperature measurements
• Tubing, piping and sheet metal temperature

TPI-5000A Deluxe Adpater Connector Kit by Test Products International

TPI-3000A Universal Cables & Connector Kit. Technicians and engineers turn to TPI for their connecting needs. With the TPI-3000A and TPI-5000A kits, technicians can create connections on the spot in seconds.

Features

• Includes 11 types of connectors for male and female adapters
• Simply screw on any combination of 35 connectors to any of the six universal interfaces with no soldering or crimping needed
• Reusable connectors can be used over and over in different combinations to fit and assist customizing the installation
• Works with universal cables GEX-60 (36"), GEX-48 (48"), and GEX-75 (72")
• Connector bodies are silver-plated machine brass with Teflon insulation
• Hard plastic case protects and organizes the individual pieces

575C1 Vane and Hotwire Velocity Meter by Test Products International

Combo Vane & hot wire anemometer and temperature. The 556 Digital Air Velocity Meter is a state of the art, easy to use instrument designed to provide temperature and air velocity readings.

The TPI 575 Vane/Hotwire Air Velocity Meter is a state of the art, easy to use instrument designed to provide temperature and air velocity readings. The instrument is ruggedly constructed and comes with a 3 Year Guarantee.

Features

• Increased versatility, uses both hot wire and vane type probes
• Measure air velocity and temperature simultaneously
• Record, minimum, maximum and average
• Data hold
• Auto power off (10 min.)
• Low battery display
• Multiple units of measure: (m/s, k/h, mile/h, knots, ft./min)
• Download data to a computer using the RS-232 port and optional A500 cable
• 39" cable length

Applications

• Air velocity measurements in heating, ventilation and air conditioning systems
• Where low and high feet per minute readings are critical you must use a hotwire below 80 ft. per minute

Standard Accessories

• TPI 575 Instrument
• Hotwire Probe Head
• Vane Probe Head
• Rubber Boot
• Soft Carrying Case
• Batteries
• Instruction Manual

Optional Accessories

• Serial Computer Interface RS232

621C3 Dual Input Differential Manometer Kit by Test Products International

Differential input high resolution manometer with A612 protective boot, two A603 1/8" barbed NPT fittings, two A605 1/8" barbed T fittings, two A776 static tips, and A908 carrying case with shoulder strap.

The TPI 621C3 is a hand held pressure meter with superior resolution.

All of these models measure over the range of -40.0 to +120.0 mbar. Each unit has a resolution of 0.01 mbar to +19.00 mbar and automatically auto-ranges above ± 19.00 mbar to 0.1 mbar resolution. Each model is supplied complete with carry pouch, battery and instruction manual.

The 621C3 includes all of the specs of the Model 621 and additionally consists of the following:

• 621 Manometer: + A612 Boot with tilt stand
• A605 T Fitting (x2): Ideal for use on setting pressure switches
• A776 Static Tip (x2): Measure static pressure with A776. It has a magnet to secure in place in duct work 1/4" hole required to use
• A774 Tubing: 6 foot length of silicone tubing for pressure measurements. Very flexible and will not go hard in cold temperatures.
• A791 Adapter Tube: Flexible tubing for connecting to larger fittings
• A908 Carrying Case: Soft padded case with shoulder strap holds the thermometer and probes.

623 Dual Input Differential Manometer by Test Products International

The TPI 623 Dual Input Differential Manometer is a high accuracy hand held pressure meter with superior resolution.

The TPI 623 is a hand held pressure meter with superior resolution.

Features and Benefits

• 0.001 inH2O / kPa resolution up to +/-9.999 inH2O / kPa input
• Accuracy: ±0.02 inH2O (< 2 inH2O) ±1% (> 2 inH2O)
• Dual input differential
• Autoranging
• Seven selectable units of measure (mbar, kPa, PSI, mmHg, inHg, mmH2O, inH2O)
• Backlit Display

Applications

• Check for positive building pressure
• Perform room to room pressure diagnostics
• Test duct pressure and perform static pressure checks
• Adjust appliance regulators
• Test pressure switch operation on a 2-sage gas furnace in both positive and negative pressures

Standard Accessories (Included)

• 9V Alkaline battery (A009A)
• Soft Pouch (A600)
• Protective boot with magnets (A6XX)
• Silicone tubing with 1/4" barbed 1/8" NPT fitting (A603)

625 Dual Input Differential Manometer by Test Products International

Dual Differential Input Manometer with ±80 inH2O range and 0.01 in H2O resolution. Seven units of pressure: inH2O, mbar, KPa, PSI, mmH2O, mmHg, inHg, Auto power off, Record/Min/Max, Backlight display, Zero function, Trim mode to stabilize readings.

The TPI 625 is a hand held pressure meter with superior resolution.

All of these models measure over the range of -40.0 to +120.0 mbar. Each unit has a resolution of 0.01 mbar to +19.00 mbar and automatically auto-ranges above ± 19.00 mbar to 0.1 mbar resolution. Each model is supplied complete with carry pouch, battery and instruction manual.

Features:

• Dual input with ±80" H2O range
• Seven units of measure (mbar, kPa, PSI, mmHg, inHg, mmH2O, inH2O)
• Display - 4 digit dual line with backlight
• Smooth - Stabilizes display when measuring fluctuating pressures
• Data Hold - Freezes reading on display
• Min / Max - Records Min/Max readings
• Auto Off - Conserve battery power.

635 Dual Input Differential Manometer by Test Products International

Dual Differential Input Manometer with ± 5 psi range and 0.001 psi resolution. Seven units of pressure: inH2O, mbar, KPa, PSI, mH2O, mmHg, inHg, Auto power off, Record/Min/Max, Backlight display, Zero function, Trim mode to stabilize readings.

The TPI 600 Tuffman series is a hand held range Of pressure meters and can be summarized as follows:

• TPI 635 5 PSI pressure range
• TPI 645 30 PSI pressure range
• TPI 655 100 PSI pressure range

All of these models are dual input differential pressure meters with 7 selectable scales to choose from: mbar, kPa, PSI, inHg. mmHg,inH20, and mH20.

Features

• Dual input with ±80" H2O range
• Seven units of measure (mbar, kPa, PSI, mmHg, inHg, mmH2O, inH2O)
• Display - 4 digit dual line with backlight
• Smooth - Stabilizes display when measuring fluctuating pressures
• Data Hold - Freezes reading on display
• Min / Max - Records Min/Max readings
• Auto Off - Conserve battery power.

Standard Accessories (Included)

• 9V alkaline battery (A009A)
• Replacement tubing (A601)

645 Dual Input Differential Manometer by Test Products International

Dual Differential Input Manometer with ± 29 psi range and 0.1 psi resolution. Seven units of pressure: inH2O, mbar, KPa, PSI, mH2O, mmHg, inHg, Auto power off, Record/Min/Max, Backlight display, Zero function, Trim mode to stabilize readings.

The TPI 600 Tuffman series is a hand held range Of pressure meters and can be summarized as follows:

• TPI 635 5 PSI pressure range
• TPI 645 30 PSI pressure range
• TPI 655 100 PSI pressure range

All of these models are dual input differential pressure meters with 7 selectable scales to choose from: mbar, kPa, PSI, inHg. mmHg,inH20, and mH20.

Features

• Differential input with + 29 PSI range
• Seven units of measure (mbar, kPa, PSI, mmHg, inHg, mH2O, inH2O)
• Display - 4 digit dual line with backlight
• Smooth - Stabilizes display when measuring fluctuating pressures
• Data Hold - Freezes reading on display
• Min / Max - Records Min/Max readings
• Auto Off - Conserve battery power.

Standard Accessories (Included)

• 9V alkaline battery (A009A)
• Replacement tubing (A601)

645NPT Dual Input Differential Manometer by Test Products International

Dual Differential Input Manometer with ± 29 psi range and 0.1 psi resolution. Seven units of pressure: inH2O, mbar, KPa, PSI, mH2O, mmHg, inHg, Auto power off, Record/Min/Max, Backlight display, Zero function, Trim mode to stabilize readings. 1/4" NPT fittings.

The TPI 600 Tuffman series is a hand held range Of pressure meters and can be summarized as follows:

• TPI 635 5 PSI pressure range
• TPI 645 30 PSI pressure range
• TPI 655 100 PSI pressure range

All of these models are dual input differential pressure meters with 7 selectable scales to choose from: mbar, kPa, PSI, inHg. mmHg,inH20, and mH20.

Features

• Differential input with + 29 PSI range
• Dual 1/4" NPT Fittings
• Seven units of measure (mbar, kPa, PSI, mmHg, inHg, mH2O, inH2O)
• Display - 4 digit dual line with backlight
• Smooth - Stabilizes display when measuring fluctuating pressures
• Data Hold - Freezes reading on display
• Min / Max - Records Min/Max readings
• Auto Off - Conserve battery power.

Standard Accessories (Included)

• 9V alkaline battery (A009A)
• Replacement tubing (A601)

665 Manometer with Data Logging by Test Products International

Dual Input Differential Manometer with ± 100 psi range and 0.01 psi resolution. Data logging with optional A665 software and docking station. Seven units of pressure: inH2O, mbar, KPa, PSI, mH2O, mmHg, inHg, Auto power off, Record/Min/Max, Backlight display, Zero function, Trim mode to stabilize readings. 1/4" NPT fittings.

The slim design 665 is a hand-held, differential input manometer with data logging capability. Digital filter, min/max, one touch zero, and backlight display are just a few of the features of the 665.

Features

• Differential input with + 29 PSI range
• Seven units of measure (mbar, kPa, PSI, mmHg, inHg, mH2O, inH2O)
• Data Logging: Record test data with time stamp and display with optional software
• PC Communication: IR to USB Interface and PC Application software (optional p/n A665)
• Display: 4 digit dual line with backlight
• Printing: Print test results directly to the optional A740 IR printer
• Data Hold: Freezes reading on display
• Min / Max: Records Min/Max readings
• Auto Off: Conserve battery power.

Standard Accessories (Included)

• Two 1.5 Volt Alkaline Battery (A002)
• Protective Boot with magnets (A614)

721 Combustible Gas Leak Detector with LCD Display by Test Products International

The 721 offers 10ppm sensitivity to detect combustible gasses. Easily operated with one hand, leaks are pinpointed using the audio and visual indicators. An adjustable tic rate helps eliminate background gas concentration in contaminated environments.

The ergonomically designed 721 is a hand-held, combustible gas leak detector. It is capable of finding combustible gas leaks in pipes, fittings, regulators, etc. Additional features include the capability to display %LEL, leak level in ppm, and user adjustable alarm point.

Features

• Combustible Gas Leak Detector capable of displaying real ppm, stepped ppm, and %LEL (Lower Explosive Limit).
• 10ppm sensitivity (methane)
• Detect combustible gases including natural gas, propane, butane, etc.
• Thumbwheel adjustable tic rate to locate leaks quickly and accurately
• Two line display with bargraph and backlight
• Audio / Visual alarm indication with user adjustable alarm point
• Earphone jack for use in noisy environments
• Approximately 20 hours of continuous use (C cell alkaline batteries x2)

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

Standard Accessories

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

770 Carbon Monoxide Monitor by Test Products International

The 770 CO Single Gas Monitor is a state-of- the-art Carbon Monoxide Instrument designed to measure Carbon Monoxide in ambient air and to perform a carbon monoxide build up test . It has a measurement range of 0 to 999 ppm (parts per million) and displays the readings in 1ppm increments.

The unit features a personal audible and visual alarm, which is factory set at 30ppm CO but can be changed in the field to keep current with government legislation.

Other features include: maximum reading hold, elapsed time and manual zero. The audible alarm may be switched on and off as required. Battery changing is made easy by use of a simple slide off battery compartment cover.

The detector uses an advanced electrochemical sensor that measures Carbon Monoxide and should not be used for any other purpose.

When the audible alarm is switched off a small 'double speaker' symbol will be displayed at the bottom left of the LCD. When the alarm setting is exceeded a 'warning' symbol is displayed at the bottom center of the screen and the red warning indicator is illuminated. As the battery level approaches 2 volts a 'BAT' warning symbol is displayed to indicate low battery level. When the battery level gets too low the unit will automatically switch off.

Features

• Measure CO from O to 999ppm
• Displays the max. CO reading in PPM since power on
• Displays in hours and minutes, time elapsed since power on
• Displays user set value of audible and visual alarm
• The audible alarm can be switched on and off by pressing the SEL button

Applications

• Ambient CO safety checks

A254 AC/DC Amp Low Current Probe Adapter by Test Products International

Most TPI brand and any competitor DMM, clamp-on or oscilloscope having the capability of measuring up to 2000mV AC/DC (2V AC/DC), 10M Ohm input impedance, and equipped with industry standard spaced input jacks 19mm on center.

A620 Pressure Adapter by Test Products International

Most TPI brand and any competitor DMM, clamp-on or oscilloscope having the capability of measuring up to 2000mV AC/DC (2V AC/DC), 10M Ohm input impedance, and equipped with industry standard spaced input jacks 19mm on center.