$50 - $75, Test and Measurement

725 Pocket Combustible Gas Detector by Test Products International

The 725 offers 1000ppm sensitivity to detect combustible gasses including natural gas, methane, propane (LPG), diesel, and kerosene.

Trace fuel lines, tanks and containers for gas leaks. Once a leak is detected, the 725 will sound an alarm and the red LED s will light showing level of leak.

Features

• 1000ppm sensitivity
• Trace natural gas lines and fittings for leaks
• Check gas equipment for leaks
• Test propane tanks, fittings, lines, and heaters for leaks
• Check propane tanks, fitting lines, and heaters for leaks.
• Test confined spaces for gas build-up
• Fits in shirt pocket
• Responds instantly

Applications

• Check gas generation for leaks

Standard Accessories

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

22277-2 Power Cable - 20 FT by WeatherHawk

WeatherHawk input power cable in a 20 foot (6 meter) length. Use for connection of an external power supply (12-18 volt DC, 1 amp source) to any WeatherHawk weather station.

Terminated with a weatherproof connector on the WeatherHawk end, and terminated, with a jack connector with strain relief (5.5 mm O.D. x 2.5 mm I.D. x 9 mm deep) on the other end.

Shipping weight: less than 1 pound (0.45 Kg).

0560 8051 805 Mini IR Thermometer by Testo

The compact 80 mm infrared thermometer fits into any pocket and is always within reach e.g. for measurements in Incoming goods and for checking the cold shelves in supermarkets. Also ideal for rapid measurements in the food industry and in the home.

• High accuracy in a critical area for food
• Packaging remains undamaged
• TopSafe is dishwasher-proof
• Display of minimum and maximum values
• Scan mode for permanent measurement
• Robust, waterproof protection case (IP65), optional
• Practical and compact, pocket-size
• High accuracy in the critical range for food
• Water-proof and robust on account of dishwasher-safe protection sleeve TopSafe (IP65)
• Minimum and maximum value display
• Scan mode for long-term measurements

16775 TP1-GR Grounding Kit by WeatherHawk

The grounding kit consists of a 36 inch (91.4 cm) long copper plated steel electrical ground rod, electrical couplings for connection to the ground rod and the TP1 Tripod, a 5 foot length of plastic coated 00 stranded copper cable, and a three foot length of 14 AWG stranded copper ground wire with a connection lug on one end. This kit enables proper earth grounding of the TP1 Tripod and WeatherHawk weather station if installed by a qualified electrician.

pH630F pH/Temperature & Replaceable pH Electrode by Jenco

VisionPlus pH630 is a rugged, easy to use, IP67 rated pH tester with temperature readout. Key features include IP67 rated body, automatic temperature compensation, up to 3 point calibration and replaceable electrode module. Available in degrees Celsius and degrees Fahrenheit models.

This pH tester is RoHS compliant.

• Automatic temperature compensation
• 1, 2 or 3 point calibration
• Stores calibration data
• Replaceable electrode module
• High noise resistance
• Simultaneous display of pH and temperature
• Large temperature range
• Dedicated button for data hold
• Low battery indicator
• IP67 rated body for water-proof and dust-proof
• RoHS compliant

77A-T Thermocouple/RTD 2-Wire Transmitter, Type T, Ambient Temperature Range -40 to 85 °C by Jenco

2-wire thermo well head type 4-20 mA current loop output signal temperature transmitter for thermocouple or RTD applications, 3 user selectable temperature ranges and adjustable Zero Span with current output proportional to the display LED s brightness. Two ambient temperature ranges are available model 77 and 77A. Specify type J, K, E, T or RTD and specify temperature range.

• Fits standard thermo well heads
• 12-36 vdc powered
• 3user-select measurement ranges
• Current proportional led brightness
• Factory calibrated
• User adjustable zero/span
• 2ambient temperature ranges
• Factory custom calibration available

Measuring Range: -50 to +250°C

08610-26 Traceable® Wall-Mount Digital Clock/Calendar/Thermometer with Calibration by Digi-Sense

Perpetual calendar shows month, date, day of week, and automatically adjusts for leap year. Selectable temperature display for °F or °C; shows room temperature to the nearest 0.5°. Attractive two-tone housing with built-in wall mount bracket.

Traceable® products are calibrated to NIST-traceable standards and ready to use as soon as you receive it. Each product goes through an intense vetting process before it can carry the Traceable name, and it includes NIST-traceable certification. This means that a 17025-accredited calibration test lab has confirmed that the product meets or exceeds all stated specifications, saving you both time and money by not having to calibrate separately.

NIST-traceable calibration also helps you meet quality standards and regulatory compliance for ISO, FDA, cGMP, VFC, CAP, CLIA and Joint Commission requirements.

Features:

• Get accurate, reliable measurements with included NIST-traceable calibration
• Quartz-crystal timing accuracy of 0.01%

Includes:

Two AAA batteries and NIST-traceable calibration certificate with data.

16772 TP1-GK Guy-wire Kit by WeatherHawk

The Guy-wire Kit contains three precut lengths of plastic coated, steel guy-wire cable, and all hardware required to secure the guy-wires to the top of the TP1 tripod mast, and the bottom of the tripod legs. Alternatively, the bottom connection can be made to eye-bolts set into a concrete pad, or other fixed structure. The guy-wire kit is designed for permanent WeatherHawk installations, or for TP1 tripod configurations with two extension poles, or for locations that experience sustained periods of very high wind.

Box size/Wgt: 11 x 8 x 3 inches (28.6 x 20.8 x 7.8 cm), 3.1 pounds (1.4 kg). NOTE: May be packed with other items if ordered as a part of a system.

SCT-108.002.NA Flexible Electrode Holder by ScichemTech

• Flexible electrode holder
• Nice appearance of the arc-type bracket
• You can turn 360 degrees
• Vertical lift

17488 TP1-EP Tripod Extended Footpads by WeatherHawk

Extended, oversized footpads that enable the use of sandbags to stabilize a WeatherHawk weather station tripod for temporary site locations or quick response applications.

Just site the tripod, establish proper orientation and drop a sandbag on each footpad. No need to drive difficult to remove ground stakes.

Box Size/Shipping Wgt: 6 x 6 x 12 inches (15.2 x 15.2 x 30.4 cm), 2.5 pounds (1.1 kg).

TLSHVACR1 HVAC/R Test Lead Kit by Test Products International

Includes

• A052 M4.0/0.7 Thread Safety Plug Adaptor
• A054 Modular Test Prod Set with Sharp Steel Point
• A057 Pair Back Probing Probes Part
• A066 1000V Fully Insulated Crocodile Clip.
• A067 Modular Grabber Clips
• A081 Modular Silicone Test Lead Set

IP250 Switchable Passive Oscilloscope Probe, 250MHz, 1.5M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

ACH4 400A Amp Clamp Accessory Head by Fieldpiece

The ACH4 current clamp is a small size accessory head for quickly reading up to 400 AC amps. The claw feature on the clamp makes it easy to quickly pick out the wire you need to measure. Once the current carrying conductor is isolated, the amperage is converted to mVAC for reading directly on the meter. The ACH4 works with the Fieldpiece "Stick" meter, EHDL1 Electronic Handle, EH4W Wireless Handle, DL3 Data Logger, the HG2 and HG3 HVAC Guide® System Analyzers, or any other digital multimeter (with mVAC range) connected by Fieldpiece ADLS2 detachable silicone leads or AHDL1 handle adapter.

Features

• Connect directly to any Fieldpiece stick meter (shown attached to HS36)
• Remote the amp clamp for hard to reach areas using our deluxe silicone leads with detachable probe tips (model ADLS2)
• Angled jaw opens to 1.8 inches and makes singling out a wire fast and easy

Included

• 400A Amp Clamp Accessory - ACH4
• Operator's Manual

120085 Individual BNC Attenuator, 20 dB 0.5 Watt by Test Products International

Features

• Increase the input range of an oscilloscope.
• Reduce the output level of fixed amplitude signal sources.
• Connect low impedance sources to instruments with high-impedance inputs.