$2000 - $4000, Personnel Hoists and Quick Release Retrieval Winches, Pelsue

PHQR-T45 45' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PH07R Personnel Hoist with 70' x 1/4" Synthetic Cord & Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PH07C Personnel Hoist with 70' Stainless Steel Cable and Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PH05C Personnel Hoist with 50' Stainless Steel Cable and Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PH10C Personnel Hoist with 100' x 3/16" Stainless Steel Cable and Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PH10R Personnel Hoist with 100' x 1/4" Synthetic Cord & Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PH15C Personnel Hoist with 150' x 3/16" Stainless Steel Cable and Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PH15R Personnel Hoist with 150' x 1/4" Synthetic Cord & Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PHQR No Rope, Hoist Only by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQR-S45 45' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQR-T70 70' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQR-X45 45' Technora Rope and Wichard Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQRR Reverse Winding, No Rope, Hoist Only by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQRR-S45 Reverse Winding with 45' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQRR-T45 Reverse Winding with 45' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQRR-T70 Reverse Winding with 70' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHQRR-X45 Reverse Winding with 45' Technora Rope and Wichard Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

PHT07C Personnel Hoist with 70' Stainless Steel Cable and Tripod Bracket by Pelsue

Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features, line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. These hoists are designed for use with a tripod for davit base compatible systems please see the PH series hoists.

All PHT Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• "Free-wheeling" preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PHT07R Personnel Hoist with 70' x 1/4" Synthetic Cord and Tripod Bracket by Pelsue

Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features, line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. These hoists are designed for use with a tripod for davit base compatible systems please see the PH series hoists.

All PHT Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• "Free-wheeling" preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PHT10C Personnel Hoist with 100' x 3/16" Stainless Steel Cable and Tripod Bracket by Pelsue

Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features, line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. These hoists are designed for use with a tripod for davit base compatible systems please see the PH series hoists.

All PHT Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• "Free-wheeling" preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PHT10R Personnel Hoist with 100' x 1/4" Synthetic Cord and Tripod Bracket by Pelsue

Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features, line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. These hoists are designed for use with a tripod for davit base compatible systems please see the PH series hoists.

All PHT Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• "Free-wheeling" preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PHT15C Personnel Hoist with 150' x 3/16" Stainless Steel Cable and Tripod Bracket by Pelsue

Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features, line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. These hoists are designed for use with a tripod for davit base compatible systems please see the PH series hoists.

All PHT Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• "Free-wheeling" preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PHT15R Personnel Hoist with 150' x 1/4" Synthetic Cord and Tripod Bracket by Pelsue

Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features, line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. These hoists are designed for use with a tripod for davit base compatible systems please see the PH series hoists.

All PHT Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• "Free-wheeling" preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included