Calibration, Oakton

WD-17004-00 InnoCal NIST-Traceable Calibration; IR (Infrared) Thermometer by Oakton

• Testing range from -12 to 500°C (10 to 932°F)
• NIST-traceable infrared calibrations performed by using black-body calibration sources with defined emissivities

WD-17006-03 InnoCal NIST-Traceable Calibration; 2 to 4 Points, Liquid-in-Glass Thermometer by Oakton

Glass thermometers are one of the most common types of temperature instruments and are available in a variety of styles, sizes, and versions. Their unique characteristics of wide range, precision, repeatability, and quick response create a unique challenge for the metrologist who is calibrating these instruments. InnoCal can calibrate spirit-in-glass (SIG) thermometers. Calibrations for glass thermometers use direct comparison in high-stability liquid baths using Precision Reference Thermometers (PRTs) and Standard Platinum Resistance Thermometers (SPRTs) and high precision displays. The glass thermometers are inspected for cracks and liquid-column separations before testing.

• InnoCal is the only authorized service center for ERTCO brand liquid-in-glass (LIG) thermometers in the United States
• We also calibrate any make and model of LIG thermometers including Brooklyn Thermometer, Miller and Weber, Inc., LSW, and H-B Instruments
• Testing range for liquid-in-glass thermometers is from -80 to 420°C (-176 to 788°F)
• Calibrated at manufacturer's recommended points or at your desired points depending on your specific requirements. Correction factors are also provided for your convenience.

To meet your calibration needs:

• All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's), and test uncertainty ratios (TUR's) at no additional cost!
• This NIST-traceable calibration allows you to confirm that the specific asset you purchase meets the manufacturer's published specification
• EPA, USDA, ISO, and GLP/GMPs standards require regular NIST-Traceable calibration of all test equipment being used in critical applications
• Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays

All measurements reported are traceable to SI units via national standards maintained by NIST and performed in compliance with ANSI Z540, ISO17025, and MIL-STD-45662A. FDA Compliant.

InnoCal is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) under certificate number 1746.01. This accreditation is your assurance that the calibration is performed in a qualified, controlled laboratory.

Calibrations on glass thermometers are performed using direct comparison in high-stability liquid baths using high-precision PRT's and SPRT's and displays. Thermometers are inspected for cracks and liquid-column separations before testing. Measurements are performed at 2 to 4 points between -197°C and 550°C.

Points are generally selected at the manufacturer's specified points but customer-specified points can be accommodated. For certificates with more calibrations points, see 17006-05 for 5 to 9 points, and 17006-06 for 10 to 15 points.

WD-17006-05 InnoCal NIST-Traceable Calibration; 5 to 9 Points, Liquid-in-Glass Thermometer by Oakton

Glass thermometers are one of the most common types of temperature instruments and are available in a variety of styles, sizes, and versions. Their unique characteristics of wide range, precision, repeatability, and quick response create a unique challenge for the metrologist who is calibrating these instruments. InnoCal can calibrate spirit-in-glass (SIG) thermometers. Calibrations for glass thermometers use direct comparison in high-stability liquid baths using Precision Reference Thermometers (PRTs) and Standard Platinum Resistance Thermometers (SPRTs) and high precision displays. The glass thermometers are inspected for cracks and liquid-column separations before testing.

• InnoCal is the only authorized service center for ERTCO brand liquid-in-glass (LIG) thermometers in the United States
• We also calibrate any make and model of LIG thermometers including Brooklyn Thermometer, Miller and Weber, Inc., LSW, and H-B Instruments
• Testing range for liquid-in-glass thermometers is from -80 to 420°C (-176 to 788°F)
• Calibrated at manufacturer's recommended points or at your desired points depending on your specific requirements. Correction factors are also provided for your convenience.

To meet your calibration needs:

• All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's), and test uncertainty ratios (TUR's) at no additional cost!
• This NIST-traceable calibration allows you to confirm that the specific asset you purchase meets the manufacturer's published specification
• EPA, USDA, ISO, and GLP/GMPs standards require regular NIST-Traceable calibration of all test equipment being used in critical applications
• Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays

All measurements reported are traceable to SI units via national standards maintained by NIST and performed in compliance with ANSI Z540, ISO17025, and MIL-STD-45662A. FDA Compliant.

InnoCal is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) under certificate number 1746.01. This accreditation is your assurance that the calibration is performed in a qualified, controlled laboratory.

Calibrations on glass thermometers are performed using direct comparison in high-stability liquid baths using high-precision PRT's and SPRT's and displays. Thermometers are inspected for cracks and liquid-column separations before testing. Measurements are performed at 5 to 9 points between -197°C and 550°C.

Points are generally selected at the manufacturer's specified points but customer-specified points can be accommodated. For certificates with more calibrations points, see 17006-06 for 10 to 15 points.

WD-17040-10 InnoCal NIST-Traceable Calibration; Pressure/Vacuum Gauge, Accuracy ?1% by Oakton

If your experiment or process relies on pressure and vacuum measurements, make sure these instruments remain precise through regular calibrations. InnoCal® performs NIST-traceable pressure calibrations on absolute, gauge, and vacuum measuring instruments from:

• Gauge, Absolute and Differential Pressure from 0 to 20,000 psig (1.38 mPa)
• Vacuum from 0 to 29.2 in. Hg (986 mBar)
• Barometric pressure from 700 to 1100 mBar

We can calibrate all styles of pressure and vacuum equipment including analog/dial gauges, digital gauges, transducers and transmitters, pressure calibrators, manometers, barometers, deadweight testers, and pressure comparators.

InnoCal services all major brands of pressure equipment including Ashcroft®, WIKA®, Crystal Engineering, Fluke®, Druck, GE Sensing, Cole-Parmer®, Extech®, 3D Instruments™, and many more!

To meet your calibration needs:

• All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's), and test uncertainty ratios (TUR's) at no additional cost!
• This NIST-traceable calibration allows you to confirm that the specific asset you purchase meets the manufacturer's published specification
• EPA, USDA, ISO, and GLP/GMPs standards require regular NIST-Traceable calibration of all test equipment being used in critical applications, FDA compliant
• Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays

All measurements reported are traceable to SI units via national standards maintained by NIST and performed in compliance with ANSI Z540, ISO17025, and MIL-STD-45662A.

InnoCal is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) under certificate number 1746.01. This accreditation is your assurance that the calibration is performed in a qualified, controlled laboratory.

Calibrations on pressure and vacuum gauges are performed using direct comparison against ultra-precise quartz reference transducers. Pressure measurements can be taken up to 20,000 psi and vacuum measurements down to 29.2 inches of Mercury. The calibration consists of 5 points upscale and 5 points downscale across the range of the instrument.

WD-17040-30 InnoCal NIST-Traceable Calibration; Pressure/Vacuum Gauge, Accuracy ?1% by Oakton

If your experiment or process relies on pressure and vacuum measurements, make sure these instruments remain precise through regular calibrations. InnoCal® performs NIST-traceable pressure calibrations on absolute, gauge, and vacuum measuring instruments from:

• Gauge, Absolute and Differential Pressure from 0 to 20,000 psig (1.38 mPa)
• Vacuum from 0 to 29.2 in. Hg (986 mBar)
• Barometric pressure from 700 to 1100 mBar

We can calibrate all styles of pressure and vacuum equipment including analog/dial gauges, digital gauges, transducers and transmitters, pressure calibrators, manometers, barometers, deadweight testers, and pressure comparators.

InnoCal services all major brands of pressure equipment including Ashcroft®, WIKA®, Crystal Engineering, Fluke®, Druck, GE Sensing, Cole-Parmer®, Extech®, 3D Instruments™, and many more!

To meet your calibration needs:

• All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's), and test uncertainty ratios (TUR's) at no additional cost!
• This NIST-traceable calibration allows you to confirm that the specific asset you purchase meets the manufacturer's published specification
• EPA, USDA, ISO, and GLP/GMPs standards require regular NIST-Traceable calibration of all test equipment being used in critical applications, FDA compliant
• Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays

All measurements reported are traceable to SI units via national standards maintained by NIST and performed in compliance with ANSI Z540, ISO17025, and MIL-STD-45662A.

InnoCal is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) under certificate number 1746.01. This accreditation is your assurance that the calibration is performed in a qualified, controlled laboratory.

WD-17060-00 InnoCal NIST-Traceable Calibration; Timer/Stopwatch by Oakton

Calibrations on timers and stopwatches are performed using a precision timometer. Measurements can be taken from 60 seconds to 720 hours.

WD-17080-00 InnoCal NIST-Traceable Calibration; Air/Gas Flowmeter by Oakton

With the variety of flowmeter types - from differential pressure to magnetic to ultrasonic - it helps to have highly trained metrologists calibrating the meters for optimal performance. At InnoCal, our computerized, automated standards allow us to perform NIST-traceable mass and correlated flow measurements using air or nitrogen gas. When correlation to other gases is needed, our metrologists will provide you with correlated data or a gas correlation table.

Typical brands that we calibrate include Cole-Parmer, Alicat, Aalborg Instruments, Gilmont, Sierra Instruments, Bios International, and many more.

All measurements reported are traceable to SI units via national standards maintained by NIST and performed in compliance with ANSI Z540, ISO17025, and MIL-STD-45662A.

InnoCal is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) under certificate number 1746.01. This accreditation is your assurance that the calibration is performed in a qualified, controlled laboratory.

Key Features

• All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's), and test uncertainty ratios (TUR's) at no additional cost!
• This NIST-traceable calibration allows you to confirm that the specific asset you purchase meets the manufacturer's published specification
• EPA, USDA, ISO, and GLP/GMPs standards require regular NIST-Traceable calibration of all test equipment being used in critical applications, FDA compliant
• Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays
• Testing includes measurement at 5 to 10 points - depending on the meter - equidistant across the range of the flowmeter
• Testing range 0-500 LPM air flow
• Calibration service for an Air/gas flowmeter
• Testing range 0.1 to 80,000 sccm at uncertainties as low as (K=2) ±0.2% of reading
• Testing includes measurement at five to seven points - depending on the meter - equidistant across the range of the flowmeter
• Certificate includes measured data, graphs, and correlations (if required) to meet the most stringent quality and scientific requirements

WD-17080-10 InnoCal NIST-Traceable Calibration; Mass Flowmeter by Oakton

With the variety of flowmeter types - from differential pressure to magnetic to ultrasonic - it helps to have highly trained metrologists calibrating the meters for optimal performance. At InnoCal, our computerized, automated standards allow us to perform NIST-traceable mass and correlated flow measurements using air or nitrogen gas. When correlation to other gases is needed, our metrologists will provide you with correlated data or a gas correlation table.

Typical brands that we calibrate include Cole-Parmer, Alicat, Aalborg Instruments, Gilmont, Sierra Instruments, Bios International, and many more.

All measurements reported are traceable to SI units via national standards maintained by NIST and performed in compliance with ANSI Z540, ISO17025, and MIL-STD-45662A.

InnoCal is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) under certificate number 1746.01. This accreditation is your assurance that the calibration is performed in a qualified, controlled laboratory.

Key Features

• All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's), and test uncertainty ratios (TUR's) at no additional cost!
• This NIST-traceable calibration allows you to confirm that the specific asset you purchase meets the manufacturer's published specification
• EPA, USDA, ISO, and GLP/GMPs standards require regular NIST-Traceable calibration of all test equipment being used in critical applications, FDA compliant
• Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays
• Testing includes measurement at 5 to 10 points - depending on the meter - equidistant across the range of the flowmeter
• Testing range 0-500 LPM air flow
• Calibration service for an Air/gas flowmeter
• Testing range 0.1 to 80,000 sccm at uncertainties as low as (K=2) ±0.2% of reading
• Testing includes measurement at five to ten points - depending on the meter - equidistant across the range of the flowmeter
• Certificate includes measured data, graphs, and correlations (if required) to meet the most stringent quality and scientific requirements

WD-17090-00 InnoCal NIST-Traceable Calibration, Multimeter, Handheld, 45-digit by Oakton

All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's) and test uncertainty ratios (TUR's) at no additional cost!

NIST-traceable calibration allows you to confirm that the specific asset you purchase does in fact meet the manufacturer's published specification. Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays. EPA, USDA, ISO and GLP/GMP standards require regular NIST-Traceable calibration of all test equipment being used in critical applications.

Calibrations on 4.5 digit handheld multimeters are performed using high-accuracy multi-function calibrators and standards-grade reference multimeters per manufacturer's recommended procedures. Measurements can be taken up to 40,000 Volts, 1000 Amps, 10 Tera-Ohms, 110 Mega-Farads, and 1.1 Giga-Hertz.

Key Features

• Provides traceability to NIST
• Lists the environmental conditions present at time of calibration
• Certificate lists actual values, uncertainties, and tolerances
• Regular calibration helps you meet ISO, EPA, GLPs/GMPs and other quality standards
• Not an accredited certificate
• Calibration service for a handheld multimeter, 4.5-digit

Includes

Calibration reports issued by InnoCal may not be reproduced, except in full, without written permission of InnoCal. The results stated in our reports relate only to the items tested or calibrated.

WD-17100-00 InnoCal NIST-Traceable Calibration; Recorder, (non-temp or X-Y) by Oakton

Calibration reports issued by InnoCal may not be reproduced, except in full, without written permission of InnoCal. The results stated in our reports relate only to the items tested or calibrated. Measurements reported on our reports are traceable to SI units via national standards maintained by NIST and are performed in compliance with MIL-STD-45662A, ANSI/NCSL Z540-1-1994, 10CFR50, Appendix B, ISO9002-94, and ISO/IEC 17025:2005

• NIST-Traceable calibrations for non-temp or X-Y recorders

WD-17100-10 InnoCal NIST-Traceable Calibration; Recorder, X-Y by Oakton

Calibration reports issued by InnoCal may not be reproduced, except in full, without written permission of InnoCal. The results stated in our reports relate only to the items tested or calibrated. Measurements reported on our reports are traceable to SI units via national standards maintained by NIST and are performed in compliance with MIL-STD-45662A, ANSI/NCSL Z540-1-1994, 10CFR50, Appendix B, ISO9002-94, and ISO/IEC 17025:2005

• NIST-Traceable calibrations for non-temp or X-Y recorders

WD-17104-00 InnoCal NIST-Traceable Calibration; Pipettors, with 10 Measurements at 3 Volumes by Oakton

Calibrations on pipettes, dispensers and graduated cylinders are performed per the procedures in ISO8655 using a precision pipette accuracy tester. Before testing, the valves and seals on pipettes and dispensers are tested for integrity using a leak tester. Variable pipettors and dispensers are measured at 3 points at 10, 50 and 100% of the maximum value. Fixed pipettors and dispensers are measured at the nominal value. Evaluation of the unit under test is done for dispensed volume and the coefficient of variability (CV) value.

• NIST-Traceable calibration for pipettors with 10 measurements

WD-17105-00 InnoCal NIST-Traceable Calibration; Refractometer by Oakton

Calibration reports issued by InnoCal may not be reproduced, except in full, without written permission of InnoCal. The results stated in our reports relate only to the items tested or calibrated. Measurements reported on our reports are traceable to SI units via national standards maintained by NIST and are performed in compliance with MIL-STD-45662A, ANSI/NCSL Z540-1-1994, 10CFR50, Appendix B, ISO9002-94, and ISO/IEC 17025:2005

WD-17107-00 InnoCal NIST-Traceable Calibration; Hydrometer, 1-point by Oakton

All calibration certificates contain as-found and as-left data, estimated measurement uncertainties (emu's) and test uncertainty ratios (TUR's) at no additional cost!

NIST-traceable calibration allows you to confirm that the specific asset you purchase does in fact meet the manufacturer's published specification. Receive your product calibrated and ready to use rather than sending it to a third-party or internal calibration lab and incurring additional delays. EPA, USDA, ISO and GLP/GMP standards require regular NIST-Traceable calibration of all test equipment being used in critical applications.

• Provides traceability to NIST
• Lists the environmental conditions present at time of calibration
• Certificate lists actual values, uncertainties, and tolerances
• Regular calibration helps you meet ISO, EPA, GLPs/GMPs and other quality standards
• Not an accredited certificate

Includes

Calibration reports issued by InnoCal may not be reproduced, except in full, without written permission of InnoCal. The results stated in our reports relate only to the items tested or calibrated.