FS7 Flame Detectors, Honeywell Analytics

FS7-2173-2RPT15 FS7 Multi-Spectrum Fire and Flame Detector, 20FT CBL 180IN TFLN VITON 2 RLY by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-KALO FS7 Multi-Spectrum Fire and Flame Detector, Kal-rez O-ring for use with FS7-130-SX Controller, FSWB Control Panel or S7-2175 Control Panel by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-RP FS7 Multi-Spectrum Fire and Flame Detector, 20FT CBL 72IN TFLN VITON 1 RLY by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

FS7-2173-RPK FS7 Multi-Spectrum Fire and Flame Detector, 20'C/6'T, KALREZ O-RING by Honeywell Analytics

The Fire Sentry FS7-2173 electro-optical radiant energy fire detector - and the Fire Sentry FS7-2173-2RP (unitized model) with multi-spectral WideBand IR™, Near Band IR and Visible Band fire detection are designed specifically for semiconductor Clean Room fire protection applications.

The Fire Sentry FS7 fire detector provides and intelligent two-stage response to semiconductor wet bench fires:

Stage 1: Alert. This is the first-stage response to a small fire with a heat energy output of 3 kW (the equivalent of a 4-inch diameter polypropylene pool fire). This allows time for the fire to self-extinguish.

Stage 2: Alarm. If the fire does not self-extinguish, and grows to the Factory Mutual specified heat energy threshold of 13 kW (the equivalent of an 8-inch diameter polypropylene pool fire), the second-stage response is activated.

The Fire Sentry FS7-2173 is used with Fire Sentry FS7-130-SX Controller or Control Panel FSWB. Controller and Control Panel supply power to detectors monitor the status of all detectors and communicate with the detectors via the digital RS-485 communication channel. Fire Sentry FS7-2173 is supplied with a standard 20 ft. cable connector. Detectors are connected to the controller or control panel using the self-locking connectors and Fire Sentry junction boxes. This allows for fast and easy connections eliminating wiring problems. Each detector can store up to six time and date stamped FirePics™ (pre-event multi-spectral sensor array data) in non-volatile memory. Controller and control panel can also store event history table in the non-volatile memory, which contains the time and date stamped alert, alarm and fault histories. FirePics™ and event histories can be retrieved from the controller or control panel.

Fire Sentry FS7-2173-2RP unitized model's microprocessor, with digital signal processing algorithms, continuously monitors the circuitry, sensor's built-in selftest and verifies proper operation. Fire Sentry FS7-2173-2RP with discrete relay outputs is designed to operate as a stand-alone detector and interface with any approved fire alarm panel. The detector requires an external 24 VDC power source and is supplied with a standard 20 ft. pigtail cable. It can store up to six time and date stamped FirePics™ and 200 events in non-volatile memory. FirePics™ and event histories can be retrieved using a Fire Sentry FS7 Interface Kit and the Fire Sentry Windows-based PC software.

Features:

• Multi-Spectral digital electro-optical radiant energy infrared fire detector
• Unique two-stage fire detection response
• Immune to false alarm sources
• NOT affected by absorbing smoke, gasses or chemical vapors
• NOT sensitive to background radiant energy from electric heaters and ovens
• Detects hydrocarbon and non-hydrocarbon fires
• Rugged leak-proof, heat-sealed, acid-resistant, injection-molded polypropylene housing
• Wide 120° field-of-view
• Digital communication with RS-485 interface
• FirePic™; time and date-stamped digital fire signatures
• Built-in detector automatic self test
• Unitzed model design for stand-alone operation

Applications include:

• Open Areas of Clean Room
• Wet Bench Working Surface
• Wet Bench Subsurface (Plenum)
• Pumps and Equipment Located Behind the Wet Bench Area
• Under-floor Areas
• IPA Stations (Unitized model only)

Junction Box for connecting Model FS7-2173 Fire Detectors in a daisy chain or star configuration. Complete with (4) Lemo female connectors. Required for Model FS7-130-SX applications.

Wall Mount, S7/FS7 Detector

Replacement Battery for FT-S7 Tester (1 required)

Swivel Mount for FS17 PolyPro