GfG

2801-34-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Methylisobutylketone (C6H12O), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2214019 CS 21 Fixed Gas Transmitter, CFC-113 (CCl2FCClF2), 30 to 5000 ppm by GfG

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants
• Long sensor life
• Fast response

2211005 CI 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 to 1000 ppm by GfG

The charge carrier injection (CI 21) sensor is a progressive development to improve upon current ammonia refrigeration detection methods. With CI 21 technology sensor life is no longer limited to ammonia exposure levels. This reduces replacement costs associated with electrochemical sensors.

Charge carrier injection technology also eliminates false alarms frequently associated with metal oxide sensing (MOS). These, along with other features, provide reliable, cost effective, longterm safety.

The CI 21 transmitter is an advanced development to which all other ammonia transmitters will be compared.

• Stable long-life charge-carrierinjection sensor
• Sensor is unaffected by exposure to high gas concentrations
• Low temperature operation to -40oF
• Low cross-sensitivity
• Eliminates costly false alarms
• Low cost of ownership

G460-11-03-20-00-66 G460 Multi-Gas Detector with NiMH Smart Pump and NiMH Battery with Flashlights, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor, HCN by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

2801-38-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Propylene (C3H6), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2811-709-002 EC 28 Gas Transmitter with Sensor, Chlorine (Cl2), Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2200-004 GMA 200-MT6/4 GMA 200 Controller, configured for 4 measuring points by GfG

For more than 50 years, the key goal of GfG has been to meet the highest demands of occupational health and safety, industrial equipment reliability and environmental protection. This goal has been reached by developing innovative and reliable gas warning systems. Development of the new GMA 200 gas warning system satisfies these requirements while taking into account suitability testing in line with ATEX Directive 94/9/EC. If switching functions for explosion protection are required, the GMA 200 gas warning system is the optimal solution. It also meets the requirements for gas warning systems without necessary ATEX certification and functional safety requirements (SIL).

Design of the GMA 200 gas warning system

The design of the GMA 200 gas warning system ensures flexible and simple operation in industrial and commercial applications for measuring combustible and toxic gases / vapors, and for measuring oxygen concentrations. The compact design of the GMA 200 as a DIN rail module enables cost-effective and space-saving installation.

Modular design of the GMA 200 MT6 / MT16 gas warning system

Up to 16 detectors can be connected to the GMA 200 gas warning system. A software program enables the quick and easy configuration of the measuring points for already installed GMA 200 gas warning systems. Measuring point designations, the detector type, the type of gas and measuring range as well as three individual or specified alarm thresholds can be programmed for each measuring point using the configuration software. A microprocessor evaluates the analog input signals of the connected detectors.

Integrated relays

As a result of the increasing requirements being placed on safety measures, even redundant protection against gas hazards, complex gas warning systems are in demand. The GMA 200 gas warning system is equipped with 8 internal relays. 6 relays can be freely configured using the software program in order to implement safety measures and alarms. The configuration software offers numerous and flexible options, such as the assignment of one or several measuring points to relays, single alarms per measuring point and alarm threshold, configuration of collective or group alarms and fault messages and voting functions. Two further relays are available for safety-related fault messages and for maintenance.

Relay modules

Using a GMA RT relay module, it is possible to extend the GMA 200 gas warning system by 16 additional freely configurable relays. A total of 4 additional relay modules and thus 64 additional relays can be managed via the GMA 200 gas warning system. Digital connection of the GMA RT relay module to the GMA 200 gas warning system enables the local positioning of the relay modules. The local and thus flexible installation of the relay modules results in large cost savings due to reduced cabling and assembly functions.

Availability of the gas warning system

Besides the traditional voltage supply, the GMA 200 gas warning system can also be operated with a redundant, safety-related voltage supply and therefore meets the highest demands of functional safety and the required permanent availability of gas warning systems for detecting potential gas hazards.

System functions: LED displays

The status of the GMA 200 gas warning system operation, fault, service is shown via LEDs.

Graphical display

The clearly structured layout of the GMA 200 gas warning system enables the quick detection of hazardous situations. Currently measured values are permanently displayed on the LCD graphical display. In the event of gas alarms, the display lighting is automatically activated with a red background.

Additionally, the LED display for Alarm 1, Alarm 2, Alarm 3 is shown. In the event of an alarm, the status of the active relays 1-8 is displayed simultaneously via LEDs.

The integrated memory enables the reading of alarm levels and minimum / maximum values per measuring point at the LCD for an initial, quick hazard assessment.

Data logger function

The GMA 200 gas warning system can be equipped with a micro SD card for saving the measured values. The measured values, mean values, alarm events and faults are permanently stored at individually configurable intervals, and can be read out for evaluation.

Operation via keyboard

Five buttons enable operation at the GMA 200 gas warning system. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the gas warning system, detector and the relays can be retrieved in the operating menu.

Configuration

A USB port at the GMA 200 gas warning system can be used for connection to the configuration software.

Features

• A variety of transmitters can be connected for measurement of combustible, toxic gases/vapors and oxygen
• Multiple relay configurations
• Flexible, reliable and economic
• Intuitive, backlit graphical LCD with "traffic light function" (green, amber, red)
• SIL certification
• DIN rail mounting

2813-000-002 EC 28i Intrinsically Safe Transmitter with Sensor, Display by GfG

Features

• Full-featured smart transmitter for oxygen or a wide range of toxic gas measurement
• Non-intrusive AutoCal calibration adjustment
• Increased safety design to reduce installation cost in potentially hazardous locations
• Intrinsically safe (i) EX-Proof version
• BVS 04 ATEX E 132 X (electrical ex-protection) II 1G EEx ia IIC T4 C 0158
• Available in two configurations: Blind (no display), Display
• Barriers are required
• EX- conduit is not required
• Reduced installation costs

3708-050 Dynagard Stand-alone System, Chlorine (Cl2) by GfG

Single-point Area Monitors

Dynagard AutoCal^® monitors are single point detection instruments that accurately measure toxic gases and oxygen levels. Alarm lights on the front panel illuminate and an internal horn sounds when gas concentrations are exceeded.

Simple and effective

The units accurately display values on a large backlit LED and can transmit a linear 4-20 mA output. AutoCal® calibration and maintenance is done effortlessly through front panel push-buttons. Smart sensors enable the user to change measuring ranges or gas types in the field without a need for additional programming. The Dynagard is equipped with onboard relays for two adjustable alarm points. It also has one sensor fault for local connection and activation or deactivation of external devices like strobes, fans, auto dialers etc.

Features

• AutoCal® automatic calibration
• Smart sensor technology
• Digital display / control connection
• Internal push-button alarm settings

3607-050 EC 36 Fixed Gas Transmitter, Sulfur Dioxide (SO2), Display / Alarm Relays by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment

2801-07-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Ethyl acetate (C4H8O2), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2811-712-001 EC 28 Gas Transmitter with Sensor, Chlorine Dioxide (ClO2), No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2801-08-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Hexane (C6H14), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-39-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Xylene (C8H10), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2313003-1 2 GMA 313 & GMA 313EQ Stand-Alone System, Complete Set with External Alarm/Reset by GfG

State of the Art Technology

The best solution for CO2 monitoring fromthe specialists in gas detection. The GMA 313 indicates a gas hazard immediately and reliably. The built-in alarm LED and loud horn provide a warning before entering the room. The external alarm GMA 313 EQ also gives a warning wherever you want it, e.g. at the stairway or at the bar. The GMA 313 offers state-of-the-art sensor and microprocessor technology from a compact unit.

The sensor and electronics, horn and lights are integrated in one enclosure, thus saving installation costs. The robust casing is splashwater proof (IP 54), so splash-water cannot enter and damage the monitor. Thermostat control and temperature compensation of the sensor ensure reliable measurements and safety even in case of sudden temperature changes.

Low Maintenance and Long Lifetime

The infrared (NDIR) sensor has a considerably longer lifetime than an electrochemical CO2 sensor. The GMA 313 is low maintenance, robust, and reliable. Installation of the GMA 313 is very simple, just plug it into a standard 110 v ac wall outlet.

Infrared Principle

Carbon dioxide (CO2) absorbs light in the infrared range of the spectral. The NDIR technology of GfG's sensor detects the carbon dioxide concentration precisely and reliably. The infrared light emitted by a lamp passes through the gas sample. Carbon Dioxide absorbs the light in a narrow spectral range.

The remaining light is measured at the detector. The difference between emitted and detected light is proportional to the gas concentration. Water vapor and other gases, which may be presenting the sensor chamber, do not affect the light absorption in this spectral range.

Safe detection results, even with temperature changes. Precise optical measurement ensures the best accuracy and repeatability. The IR principle is as distinct as a fingerprint in criminology.

This means that only carbon dioxide is detected, thus eliminating false alarms from interfering gases. GfG Products use electronics with voltage stabilization and temperature compensation.

This results in stable measurement vales even with considerable temperature variations.

The GMA 313 has no moving parts which could be subject to wear and tear. This ensures a long lifetime and reduced service requirements. Permanent self-check of functional capability provides additional safety. Sensor and electronics are protected by a robust enclosure (IP 54).

2901-37-001 IR 29 i Gas Transmitter without Display, IP67, Propane (C3H8), 0 - 100 LEL by GfG

Measuring Principle

IR transmitters have become recognized as reliable gas warning systems for explosion protection. They are used to detect individual combustible gases or a wide range of gases. This involves sending an IR beam with a certain light intensity through a measuring space and then capturing it with a detector. Parts of this beam are absorbed by, amongst other things, hydrocarbon molecules. The reduced light intensity of the beam is registered by beam detectors and converted into a signal as the existing % LEL gas concentration.

Benefits

A special feature of our IR technology is its ability to also measure combustible gases above the lower explosion limit. Moreover, the measurement does not require oxygen.

With this technology there is basically no risk of contaminating the sensor, through silicone vapors or hydrogen sulfide, when using catalytic combustion sensors.

Operation

IR transmitters are usually used with 2 wavelengths, a so-called reference wavelength and just one measuring wavelength. Strict limits are applied to these systems. The absorption spectra of many hydrocarbons are located in the wavelength range of 3.3 μm and overlap to a large extent.

This means that gases with overlapping spectra and just one measuring wavelength can no longer be clearly distinguished. Some hydrocarbons, e.g. the frequently used welding gas acetylene, are non-absorbing in the wavelength range of 3.3 µm, but absorb instead in neighboring wavelength ranges.

In many practical applications, it is not essentially important which gas is responsible for the explosion risk. Therefore, early warnings through the broadband measurement of hydrocarbons in order to monitor the lower explosion limit (LEL) must be guaranteed. False alarms with uncritical concentrations of individual gases or solvents are thus absolutely unacceptable.

These requirements are problems for systems with 2 wavelengths.

Patented GfG Technology

The internationally patented technology of the IR 29 has been developed to solve these problems. The gold-plated mirror optics of the sensor contains 2 radiators and up to 4 detector elements with different optical filters. The precisely calculated, microstructured and pure gold coated mirror optics of the IR 29 are supplied for the first time without beam splitters.

This helps to cut signal losses by 50 % and to completely avoid the physically-related disadvantages of a beam splitter. The measured values from two additional wavelengths (4 wavelengths in total) ensure improved detection of individual gases and thus enhanced selectivity. This results in the prevention of false alarms. Only a 4 wavelength system always guarantees early warnings and the simultaneous prevention of false alarms.

New Technology

The IR 29 is the first and only intrinsically safe IR gas transmitter with patented 4-beam 4-wavelength technology.

The ignition protection class "intrinsically safe", which is so essential for industrial plants and the mining industry, is achieved by the additional use of the SB1 safety barrier and its internationally patented and innovative design.

Complete Safety Even In Zone 0

The IR 29 is the first IR gas transmitter that can also be used in Ex zone 0 and which enables maintenance as well as replacement of the sensor head without additional expense when energized.

Universal Application

The IR 29 with its robust V4A stainless steel housing has been designed to withstand the harshest environmental conditions.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Internal Data Logger

A standard built-in data logger records all the measuring data, minimum / maximum values, average values and alarm events of the last 24 hours in a ring buffer.

The recording can also be shown on the display as a 2 and 8 hour trend indicator.

The histogram mode can be selected as a permanent display of the measured values. These values are continuously updated.

Graphical Display

Measured values are shown on the high-contrast graphical display. The display can be rotated 180° depending on the installation of the IR 29.

Self Diagnosis

Processor-based signal processing enables the systematic compensation of temperature dependencies, aging influences and soiling effects. Safety-relevant functions are monitored permanently via self-diagnosis procedures and a possibly required service is indicated automatically. Daily interfering factors, such as dust and dirt accumulation, are almost completely eliminated by the innovative design.

Pressure Sensor, Moisture and Temperature Compensation

The measuring accuracy of IR sensors depends on partial pressure and thus also air pressure. Climatic fluctuations or barometric high pressure therefore influence the measuring result. Furthermore, the absorption spectrum of water almost completely covers that of hydrocarbon absorption in the 2.7 to 3.3 μm range. Air humidity therefore initially generates a measuring signal the same as the actual measuring gas. This cross-sensitivity is of particular importance in warm areas with high relative humidity. An increase in the absolute water absorption capacity of air is not linear with the temperature, i.e. three times as much water can be absorbed at 40 °C than at 20 °C. This influence can only be compensated if the current moisture content of the air is known. The IR 29 can be optionally equipped with a pressure and moisture sensor for compensation.

Maximum Safety

The innovative display enables the realization of completely safe warning concepts.

Local displays and signals directly at the device can be used to provide an early warning of potential risks.

The display at the upstream safety barrier SB1 D enables the detection of risks outside the danger zone being monitored.

This allows immediate on-site action before really hazardous situations occur.

Dust Protection

A gas permeable, water-repellent diaphragm protects the absorption space of the transmitter against dust. The additional impact protection made from robust V4A stainless steel prevents mechanical damage to the optical components.

The diaphragm can be cleaned or replaced in a matter of minutes.

Remote Controls

The IR 29 transmitter does not feature control elements for setting or servicing tasks. This helps to prevent accidental or unauthorized manipulation.

Service work at the IR 29 transmitter is carried out using the RC 2 remote control.

Features

• First intrinsically safe infrared transmitter for explosion protection
• ATEX II 1G Ex ia IIC T4 Ga C0158 can also be used in Ex zone 0
• Temperature, moisture and pressure compensation
• Patented infrared technology (NDIR)
• The energized IR sensor head can be replaced in Ex areas
• Maintenance and service-friendly

2492-025 Dynagard 25 for CO2 Stand-Alone System with IR 24 Transmitter for Detecting Carbon Dioxide (CO2) from 0-25% vol. and GMA 41B Single Channel Controller by GfG

Simple and Effective

The Dynagard 25 Series accurately measures CO2 levels. The unit offers a local display, a horn / strobe, and a linear 4-20 mA output. The Dynagard 25 Series offers a safe and reliable gas warning system.

Alarm Points

Each alarm can be adjusted separately. The alarm point values can be freely adjusted within the detection range of the transmitter. Every alarm point value can be set to over range / under range, latching / non-latching, or resettable / non-resettable.

Alarm Relays

The controller provides four voltage-free relays for the three alarms and one fault warning. The relays may be used to control additional alarm devices like lights or horns. They can even prompt specific counter measures to prevent or limit dangers from gases or vapors.

IR 24 Detection Principle: Infrared Light

Since carbon dioxide (CO2) absorbs light in the infrared spectral range, the NDIR method used in the GfG sensor can measure the carbon dioxide concentration precisely and reliably. Infrared light is sent through the sensor chamber. Carbon dioxide absorbs a part of this light in a narrow spectral range, and the remaining light is measured at the detector. The difference between the light sent and received is proportional to the gas concentration. Water vapor or other gases that can be present in the sensor chamber do not affect the light absorption in this spectrum band.

Features

• Easy installation
• Local display and horn / strobe
• Adjustable alarm points
• On-board relays for external controls
• 4-20 mA output

G450-11424K G450 Value Kit, Rechargeable Battery with Alkaline Smart Pump, O2, LEL, CO, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.