$750 - $1000, GfG Instruments, GfG

2109-500 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 500 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

Phosgene (COCl2), 0 - 2 ppm, Replacement Sensor with 6-Months Sensor Warranty

1316-004 G315 Single Gas Detector for Toxic Gases, Optimized for Ammonia (NH3) with NiMH Rechargeable Battery Pack by GfG

Pinpoint the Smallest Leaks

Small leaks in pipes or storage tanks can release enough gas to build up dangerous concentrations. The careful inspection of flanged, threaded and soldered connections before and after installation will ensure equipment and worker safety. The G300 leak detector will make leakage sprays a thing of the past

Clear and simple displays and warnings

Changing gas concentrations are indicated audibly and visually. The frequency of the audible warning rises with gas concentrations, allowing the user to pinpoint leaks. The bar graph display will warn the user if dangerous gas concentrations arise.

Light, compact and durable

Designed for one-handed operation, the G300 reacts to concentrations as small as 5 ppm and measures up to more than 10,000 ppm or 1% volume. The sensor is located at the end of a flexible gooseneck or a helix cable to allow the user to reach difficult or unreachable locations. The G300 is available with or without explosion protection for ammonia and combustible gases. The G311 operates on four "AA" alkaline batteries. All others have a rechargeable battery with run times of more than eight hours.

Features

• Small, light, and durable leak detector
• For combustible gases and ammonia
• More than 8 hours of continuous operation
• Explosion-proof models available

Standard Accessories

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

Charging Cradle, 5-unit (includes 110 VAC power supply) (charge only)

2104-2000 EC 21 Fixed Gas Transmitter with Internal Sensor, Carbon Monoxide (CO), 1 ppm, 0 - 2000 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

1418-130 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Hydrogen (H2), 0 -2000 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1316-002 G313 Single Gas Detector for Methane (Natural Gas), Propane, Refrigerant and other MOS Detectable VOCs, with NiMH Rechargeable Battery Pack by GfG

Pinpoint the Smallest Leaks

Small leaks in pipes or storage tanks can release enough gas to build up dangerous concentrations. The careful inspection of flanged, threaded and soldered connections before and after installation will ensure equipment and worker safety. The G300 leak detector will make leakage sprays a thing of the past

Clear and simple displays and warnings

Changing gas concentrations are indicated audibly and visually. The frequency of the audible warning rises with gas concentrations, allowing the user to pinpoint leaks. The bar graph display will warn the user if dangerous gas concentrations arise.

Light, compact and durable

Designed for one-handed operation, the G300 reacts to concentrations as small as 5 ppm and measures up to more than 10,000 ppm or 1% volume. The sensor is located at the end of a flexible gooseneck or a helix cable to allow the user to reach difficult or unreachable locations. The G300 is available with or without explosion protection for ammonia and combustible gases. The G311 operates on four "AA" alkaline batteries. All others have a rechargeable battery with run times of more than eight hours.

Features

• Small, light, and durable leak detector
• For combustible gases and ammonia
• More than 8 hours of continuous operation
• Explosion-proof models available

Standard Accessories

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

Chlorine Dioxide (ClO2), 0 - 2 ppm, Replacement Sensor with 2-Years Warranty

Tetrahydrothiophene (THT), 0 - 100 mg/m3, Replacement Sensor with 1-Year Warranty

Silane (SiH4), 0 - 20 ppm, Replacement Sensor with 1-Year Warranty

Ozone (O3), 0 - 1 ppm, Replacement Sensor with 1-Year Warranty

Hydrogen fluoride (HF), 0 - 10 ppm, Replacement Sensor with 1-Year Warranty

1418-022K Micro IV Value Kit with 3-Years Sensor Warranty, Oxygen (O2), 0 -0.25 vol. by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

1418-024K Micro IV Value Kit with 3-Years Sensor Warranty, Hydrogen Sulfide (H2S), Standard 0 - 100 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

1418-027K Micro IV Value Kit with 3-Years Sensor Warranty, Carbon Monoxide (CO), Standard 0 - 300 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

1418-103K Micro IV Value Kit with 2-Years Sensor Warranty, Carbon Monoxide (CO-H), 0 - 300 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

1418-106K Micro IV Value Kit with 2-Years Sensor Warranty, Carbon Monoxide (CO-H), 0 - 500 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

1418-107K Micro IV Value Kit with 3-Years Sensor Warranty, Carbon Monoxide (CO), 0 - 1000 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

1418-108K Micro IV Value Kit with 3-Years Sensor Warranty, Carbon Monoxide (CO), 0 - 2000 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

1418-111K Micro IV Value Kit with 3-Years Sensor Warranty, Hydrogen Sulfide (H2S), 0 - 500 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

1418-115 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Nitric Oxide (NO), 0 - 100 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1418-122 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Ethylene Oxide (C2H4O), 0 - 20 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1418-131 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Hydrogen (H2), 0 -0.01 vol. by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1418-132 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Hydrogen (H2), 0 -0.04 vol. by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual