Test and Measurement, Fieldpiece

RFL2 Replacement Filters and O-rings for Fieldpiece Refrigerant Leak Detectors by Fieldpiece

Fieldpiece filters and O-rings are designed to help protect your refrigerant leak detector sensor and keep it working properly. When the filter swells up and blocks water and other contaminants from reaching the sensor, it's done its job, and it's time for a replacement. You'll find the RFL2 Replacement Filter and O-ring pack at your favorite Fieldpiece distributor.

ANC8 Large Deluxe Meter Case by Fieldpiece

The Large Deluxe Meter Case, model ANC8, is a technician favorite because it handles a lot of gear for an affordable price. It has four pockets in all, including a deep center pocket that holds a combination of 2 full-size meters and 4 accessory head instruments. Features include rugged nylon construction, padding, durable pockets inside and out, a rugged double zipper and a shoulder strap. The ANC8 is a must have upgrade for any technician that has multiple Fieldpiece meters and accessory heads.

ANC1 Deluxe Meter Case by Fieldpiece

The Deluxe Meter Case, model ANC1, easily holds 1 meter and 2 accessory head instruments. Features include rugged nylon construction, padding, durable pockets inside and out, a rugged double zipper and a shoulder strap. The ANC1 comes standard with our HS30 Series Stick Multimeters.

ADMN2 Dual Port Manometer Accessory Head by Fieldpiece

The ADMN2 is a portable dual port manometer accessory head for use with our modular multimeters (DMMs) and instruments. Measures gas pressure, static pressure and pressure differential. The ADMN2 includes a zero adjust and the Auto Power-Off (APO) function to conserve battery life. Disable APO for data logging. The ADMN2 measures pressure between -60inWC and 60inWC (inches of water column) and -150.0 to 150.0 mBar. The ADMN2 also measures P1 or P2 pressure readings and calculates the difference between P1 and P2. Take static pressure measurements using the resolution mode of 0.01inWC or 0.01mBar.

The modular design of the ADMN2 gives it a distinct advantage over other dual-port manometers in the field. Remoting the ADMN2 with our detachable test leads allows you to measure pressure in hard to reach places. The included 3/16" to 5/16" adapters allow you to measure gas pressure on more makes and models of gas appliances as well.

• Measures duct pressures to balance air flow
• Resolution down to 0.01" WC for static pressure measurement
• -60.0"WC to 60.0"WC range

Includes

• Dual-Port Manometer Accessory - ADMN2
• 2 3/16" Tubes with Brass Fittings
• 2 3/16" to 5/16" Tube Adapters - RMA316
• 9V Battery (installed)
• Operator's Manual

SDMN5 Dual Port Manometer by Fieldpiece

The SDMN5 is a portable, rugged dual-port manometer designed especially for HVACR field service technicians. Measures gas pressure, static pressure and pressure differential. The SDMN5 includes a zero adjust button of the face of the meter, a rugged rubber boot, a magnet on the back for hanging the meter during service, and the Auto Power-Off (APO) function conserves battery life. The SDMN5 measures pressure between -60inWC and 60inWC (inches of water column) and -150.0 to 150.0 mBar. The SDMN5 also measures P1 or P2 pressure readings and calculates the difference between P1 and P2. Take static pressure measurements using the resolution mode of 0.01inWC or 0.01mBar. Includes 3/16" to 5/16" adapter for measuring gas inlet and outlet pressures.

The SDMN5 evolved as a result of testing pressures in the field for 20 years. Its range and resolution allow you to measure the HVAC applications you run into everyday in HVAC/R field service. Measure gas pressure on the inlet and outlets with the standard 3/16" fittings or the included adapters for 5/16" ports, take static pressure measurements across a blower and get the pressure differential with the push of a button to check drafts. Whether you're holding the ergonomic standalone shape in your hand or hang the SDMN5 on the unit with the magnetic hanger to fill out a work order, the SDMN5 make HVAC/R field service easier and faster, with less fatigue than the other guys.

• Measure duct pressures to balance air flow
• Resolution down to 0.01" WC for static pressure measurement
• -60.0" WC to 60.0" WC range
• Includes two 5/16" adapters for measuring inlet and outlet pressures

Includes

• Dual-Port Manometer - SDMN5
• 2 3/16" Tubes with Brass Fittings
• 2 3/16" to 5/16" Tube Adapters - RMA316
• 9V Battery (installed)
• Operator's Manual

HS33 Manual Ranging Digital Multimeter by Fieldpiece

The HS33 Multimeter is a great entry level modular multimeter. Like every Fieldpiece meter, it's packed with the features and functions HVACR technicians need to get the job done. The ergonomic shape fits firmly and naturally in your hand while testing. The magnetic hanger, detachable test leads and alligator clip probe tips, allow you to perform tests hands-free.

Because this multimeter has all the basics and more for a great price, many schools prefer it for their HVACR students. The rugged rubberized bumpers help this meter stand up to tough conditions in the field.

Ranges

• VAC
• VDC
• AAC
• Temperature
• Capacitance (MFD)

Features

• Non-contact voltage alert
• Quick temperature compensation
• 400AAC
• High voltage and continuity indicators
• MIN / MAX and Data HOLD
• Silicone leads with detachable probe tips
• Manual ranging
• Partners with all accessory heads to do more with one meter
• Convenient lead storage
• Safe one-handed testing

All Fieldpiece accessory heads slide directly on top of the HS33, so you can test a wider variety of parameters than what's in a single meter. The modular expandability of the HS33 makes it so you don't have to buy additional expensive meters to preform additional measurements like air flow, amps, static pressure, vacuum, and many more. There are 15 additional accessory heads to choose from.

Includes

• Expandable Manual Ranging Stick Multimeter for HVAC/R - HS33
• 400A Amp Clamp Accessory - ACH4
• Deluxe Silicone Test Leads - ADLS2
• Short Alligator Lead Extensions - ASA2
• Deluxe Meter Case - ANC1
• 9-Volt Battery (installed)
• Operator's Manual

ADLS2 Deluxe Silicone Test Leads by Fieldpiece

The ADLS2 lead set features gold plated tips, removable tip sheaths, high copper strands and are silicone insulated. They offer basket style strain relief and fit inside the test lead holders on all of out meters that have built-in holders. They're rugged and stand up to high and low temperatures better than traditional vinyl test leads and don't become brittle in extreme cold.

EHDL1 Electronic Handle by Fieldpiece

Convert any Fieldpiece accessory head instrument into a standalone with the Electronic Handle model EHDL1. It features a MAX/MIN button to record the highest and lowest reading. And a HOLD button to hold the reading. The EHDL1 has a 200 and 2000 mVAC for use with our Amp Clamp, model ACH4 and the 200 and 2000mVDC range is for use with the rest of our accessory head instruments.

MDSH1 Magnetic Parts Dish by Fieldpiece

This hanging magnet for parts and screws is a great addition to any parts bench and an even better performer in the field. Hang it on the side of a unit or any magnet-compatible metal surface. Right side up, upside down, vertically, it doesn't matter. The MDSH1 holds screws, tools and more firmly in place and out of the way while you work. It combines a strong magnet with a chrome-finish dish featuring our logotype.

RSMANK6 Valve and Knob Kit by Fieldpiece

The RSMANK6 is a replacement valve and knob kit for the SMAN2 and SMAN3 Digital Manifolds.

LT17A Digital Multimeter by Fieldpiece

This manual ranger covers the parameters and ranges you need for most HVACR applications. The LT17A meter measures current, resistance, voltage, capacitance, frequency, continuity, and temperature. Test leads store in the meter body and, with the probe tips removed, connect to any Fieldpiece accessory head. The body is made out of durable ABS plastic and comes with a bright blue backlight for poorly lit test areas. Get great accuracy using the included k-type thermocouple and an easily accessible temperature calibration pot.

The testing capabilities packed into this classic style meter is its main competitive advantage. In addition to all of the ranges, it has direct temperature measurement and works with all of our accessory heads to make it one of the most complete classic style meters available for HVACR professionals.

• Works with Fieldpiece Accessory Heads
• Continuity Indicator
• 400 AAC with included clamp
• Capacitance up to 200MFD
• Temperature up to 1400 degrees F
• Microamps DC - Flame Rectification Tests
• Frequency
• Silicone Leads with Detachable Probe TipsLTCaseStand
• Tilt Stand and Magnetic Hanger
• Bright Blue Backlight
• MAX/MIN hold
• Record the minimum or maximum reading during a measurement. To exit the MIN/MAX function, hold the button for more than 2 seconds
• Volts AC
• Volts DC
• Resistance (Ohms)
• Diode Test
• Rugged ABS case with rubber boot
• Even though it's a classic style meter it still fits naturally in your hand
• Auto power-off (APO) to conserve battery life

Includes

• Classic Style Clamp Meter with Temperature - LT17A
• Deluxe Silicone Test Leads - ADLS2
• 400A Amp Clamp Accessory - ACH4
• Wrap Tab Bead Tip Thermocouple - ATB1
• Short Alligator Lead Extensions - ASA2
• Mail Pouch-Style Instrument Case - ANC5
• 9-Volt Battery (installed)
• Operator's Manual

RFL712 Fuse for HB74 by Fieldpiece

Replace a blown fuse on Fieldpiece HVAC/R multimeter model HB74.

SRL2K7 Infrared Refrigerant Leak Detector by Fieldpiece

Like all of Fieldpiece's test instruments, the SRL2 Infrared Refrigerant Leak Detector is designed exclusively to make the HVACR Technician's job easier, faster, safer and more efficient. We set out to develop the best refrigerant leak detector for HVACR. We believe the SRL2 is it. And now it comes in kit form in a rugged, blow-mold case with all of the extras.

The ergonomic design fits naturally in your hand. The ruggedized construction stands up to abuse most other leak detectors can't handle. The eight-hour battery life lets you work all day before recharging and the included vehicle and wall chargers help you during overtime. The mute and peak functions allow you to work the way you want to work. The magnetic hanger helps keep the detector out of the way when repairing a leak, but visible enough so you won't leave it on the job.

Advantages Over Other Types of Refrigerant Leak Detectors

• Triggers on all CFCs, HFCs, HCFCs and blends.ABMK3_w_SRL2
• Sealed sensor. Unlike heated diode and corona discharge leak detectors, the sensor doesn't "touch" refrigerant as it passes through the instrument. Heated diode and corona discharge units tend to degrade or fail when they come in contact with high concentrations of refrigerant or touch liquid.
• Doesn't trigger on oil or moisture like other types of detectors.
• Senses change in refrigerant levels. Works even in contaminated environments.
• Up and running in less than 30 seconds. Some heated elements and corona discharge units take much longer to warm up. UV dyes can take several hours to travel through a running system and can degrade system components.

Designed for HVACR

• Superior - Controlled Sensitivity. Doesn't trigger on nuisance leaks unless in Turbo Mode.
• Rugged / Ergonomic Features. Ruggedized boot and it fit's in your hand.
• Infrared Sensor. Lasts up to 10 years.
• Three Sensitivity Levels. Meets new SAE standards.
• Audible/Visual Alarm. Turn the beep on or off - you decide.
• 8-hour Battery Charge. Work all day on one charge.
• Non-conductive, Sturdy Probe. Stays where you want it.
• Peak / Mute Buttons. Find leaks in noisy environments.
• Magnetic Hanger. Hang the unit while you repair the leak.
• Weighs 14-oz. Tough doesn't have to mean heavy.

Includes

• Advanced Refrigerant Leak Detector - SRL2(K7)
• (5) O-rings and 10 Replacement Filters - RFL2
• 9-inch Flex-Probe Extension - RFE2
• Rigid Extension Probe - RRE2
• Blow-Molded Case - ABMK3
• Operator's Manual

SSX34 Superheat & Subcooling by Fieldpiece

Most non-electrical HVACR problems are charge related. Many systems in operation are undercharged or overcharged. This can cause decreased efficiency and compressor failure. The higher the efficiency of a system, the more critical it is that it is charged properly.

The Fieldpiece Superheat and Subcooling for Air Conditioning and Refrigeration meter, model SSX34, measures suction line, or low side, line temperature and pressure. It then calculates actual superheat in real time using built in P/T charts. It also measures liquid line, or high side, line temperature and pressure, and calculates actual subcooling. Use it to get actual superheat on R-22, R-410A, R-134A, and R-404A fixed orifice systems and actual subcooling on TXV / TEV regulated systems.

Use the "T" fitting to charge to actual superheat or subcooling by putting the SSX34 in-line between your refrigerant bottle and the system. Use it to monitor superheat and subcooling when recovering too.

• Measures suction/liquid line pressure and temperature to calculate and display superheat/subcooling
• Display pressure in PSI or kPa
• Display temperature in °F or °C
• Display superheat in °F or °C
• Display subcooling in °F or °C
• Compatible Refrigerants: R 134A, R 404A, R 410A, R 22
• Includes "T"
• Accepts K-type thermocouples. ATC1 included
• Magnetic hanger
• Thermocouple calibration pot on meter face
• Atmosphere pressure calibration

Competitive Advantages

Many AC system analyzers include PT charts you don't want or need. The SSX34 gives you actual superheat and subcooling in real time like the expensive analyzers do in a rugged, compact design. The SSX34 constantly displays refrigerant line pressure, toggles between line temp actual superheat, and actual subcooling for four of the most common refrigerants found in HVAC/R field service. If need you need more refrigerants in your daily work, check out the HVAC GUIDE® System Analyzer (link to HVAC GUIDE PRODUCT PAGE), models HG2 or HG3, and the ASX14 for a system analyzer and then some. P/T charts for 12 of the most common refrigerants you use in HVACR are included, as well as the software and firmware to generate for printable work orders for customers. For even easier refrigeration testing take a look at the ATC1R pipe clamp especially designed to fit smaller refrigerant lines.

Includes

• Real-time Superheat and Subcooling for A/C and Refrigeration - SSX34
• Pipe-Clamp Thermocouple 3/8" to 1 3/8" for Air Conditioning - ATC1
• 9V Battery (installed)
• Operator's Manual

SIG1 Gun Style IR Thermometer by Fieldpiece

Among our most popular IR thermometers the SIG2 Gun-Style Thermometer features a 10:1 field of view. A bright blue backlight and laser guide make taking fast and accurate temperature readings easier, better and faster. The SIG1 comes with a protective lens cap and body wrap. It works faster than thermistor-based temperature instruments and has a range of -22°F to 1022°F. Includes Auto-Power Off to conserve battery life.

ATB1 K-Type Thermocouple by Fieldpiece

The ATB1, K-type bead thermocouple is used to take temperatures of air, surfaces, or liquids up to 400°F. Using the included Velcro strap allows for easy pipe temperature measurements, though not as accurately as the ATC1 Pipe Clamp Thermocouple. Use the ATB1 for outdoor dry bulb temperatures when finding target superheat. The ATB1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple.

The wrap-tab allows the thermocouple wire to conveniently store on the plug. Just wrap the excess wire around the wrap-tab and feed it through one of the eyes. Keep a few of them set at different lengths for fast, job-specific, switching between thermocouples. No more tangled messes in your tool bag.

RWA2 Wall Charger for SRL2K7 and SRL8 by Fieldpiece

Whether you need a replacement or an extra charger for your Fieldpiece refrigerant leak detector, the RWA2 works with both the SRL2K7 and SRL8. Keep one in the office and one in your service bag because Fieldpiece leak detectors are operational while charging.

SC620 Loaded Swivel Clamp Meter by Fieldpiece

The SC620 swivel-head clamp meter is packed with all the electrical measurements HVACR professionals use everyday. It also includes a host of safety features like a high-voltage LED and beeper, a continuity warning, push button non-contact voltage (NCV), a lead holder with detachable leads, and alligator probe tips for easy one-handed testing. As far as ranges go, the SC620 clamp meter has temperature, capacitance, and microamps DC for flame diode tests. It's a rugged workhorse you can count on to get the job done easier, faster, and more safely.

The SC620 is fast reacting, easy-to-use, and rugged, with extended temperature tolerances that allow for testing in freezers and on hot rooftops.Designed specifically for HVACR field service, the SC620 is a dedicated digital multimeter that offers specific features and benefits to help HVACR professionals do more, everyday:

• Volts AC/DC
• Swivel clamp
• Magnetic strap
• Dual display
• Temperature F/C
• Capacitance
• Duty cycle %
• 400 amps AC
• Microamps DC
• Frequency via leads and clamp
• Non-contact voltage
• 50 Mega Ohm with 0.1 resolution
• Continuity
• Diode test
• Hold
• Clamp probe holder
• Low battery indicator
• Lead storage

Includes

• SC620 Meter
• ADLS2 Deluxe Silicone Lead Set with Gold Plated Tips and Removable Sheath
• ATB1 Wrap Tab Type K Thermocouple
• ASA2 Short Alligator Lead Extensions
• Velcro Strap
• 9V Battery
• ANC7 Padded Case

SC640 Loaded Clamp Meter by Fieldpiece

The SC640 clamp meter is packed with more features and measurements than any clamp meter in the HVACR industry. The loaded SC640 features lead storage, a swivel head, test lead holder, heavy duty magnetic strap, jaw flashlight, and a backlight on the dial so you can easily choose the right measurement in poorly lit spaces. Plus the SC640 hosts all the electrical measurements HVACR pros use everyday, along with features like True RMS, Inrush current, capacitance, temperature, duty cycle, and microamps DC.

The top-of-the-line SC640 clamp meter helps HVACR professionals do more everyday:

• Volts AC/DC
• True RMS
• Inrush current
• Swivel clamp
• Magnetic strap
• Probe storage
• Dual display
• Temperature F/C
• Capacitance
• Duty cycle %
• 400 amps AC
• Microamps DC
• Frequency via leads and clamp
• Non-contact voltage
• 50 Mega Ohm with 0.1 resolution
• Continuity
• Diode test
• Hold
• Clamp probe holder
• Dial backlight
• Clamp jaw light
• LCD backlight
• Low battery indicator

Includes

• SC640 Meter
• ADLS2 Deluxe Silicone Lead Set with Gold Plated Tips and Removable Sheath
• ATB1 Wrap Tab Type K Thermocouple
• ASA2 Short Alligator Lead Extensions
• Velcro Strap
• 9V Battery
• ANC7 Padded Case

STA2 In Duct Hot-wire Anemometer by Fieldpiece

The STA2 is a Hot-wire Anemometer built for the HVACR professionals' air balancing needs. The compact probe tip makes measuring air velocity directly in the duct a breeze. It's great for traversing a duct and automatically calculating CFM without the hassle and expense of a bulky hood. The 38" telescoping probe's laser etched ruling and flattened edges allows techs to locate proper measurement points within a duct, and ensures that the probe is properly aligned.

This in duct hot-wire anemometer quickly calculates CFM from air velocity and free area. And with the intuitive interface, the STA2 makes it easy to capture the correct data.

• Measures air velocity and temperature
• Calculates CFM
• Slim 38" telescoping probe for in duct traversing
• Fast response time
• Dual display for combo of real-time CFM, air velocity, or temp
• Depth and direction indicators
• Minimizes turbulence effect with time/test point averages
• Hands-free testing with stabilizing cone and magnetic hanger

Includes

• Hot-wire Anemometer - STA2
• Stabilizing Cone
• Blow-molded Case with Padding

AAV3 Air Velocity and Temperature Accessory Head by Fieldpiece

The AAV3 is an anemometer accessory head for use with our modular instruments that measures air velocity and temperature in English or Metric units: Ft/min, M/s, MPH, KM/hr, °F (degrees Fahrenheit) or °C (degrees Celsius). Multiply your air velocity by the register's free area to estimate CFM or diagnose duct blockages and quickly check the airflow balance in a conditioned space. Use with our DL3 Data Logger to track airflow or temperature over time. Features average and real time testing modes.

The AAV3 Anemometer Air Velocity and Temperature Accessory offers several features and benefits to field technicians:

• Works with any Fieldpiece expandable instrument or handle or any DMM with mVDC ranges and our detachable leads.
• Measures air velocity and measures air temperature.
• Measure in hard to reach areas using detachable test leads.
• Display readings smoothly in average mode or switch to real-time measurement.
• Low battery indicator.
• Auto-power off after 10 minutes (may be disabled).
• Estimate CFM
• Large vane covers most of register's free area

Includes

• Air Velocity and Temperature Accessory - AAV3
• 9V Alkaline Battery (installed)
• Operator's Manual

SIL2 Pen Style IR Thermometer with LED Flashlight by Fieldpiece

The SIL2 is among our most accurate IR thermometers. With a 1:1 field of view and a protective IR lens cap, the SIL2, is as small as a pen and delivers big results. Features automatic data hold, measurements in °F or °C, and has excellent accuracy: ±1.5°F and a resolution of 0.5°F. The SIL2 has a range of -27°F to 230°F and includes Auto-Power Off (APO) to conserve battery life.