Temperature/RH, Fieldpiece

ATB1 K-Type Thermocouple by Fieldpiece

The ATB1, K-type bead thermocouple is used to take temperatures of air, surfaces, or liquids up to 400°F. Using the included Velcro strap allows for easy pipe temperature measurements, though not as accurately as the ATC1 Pipe Clamp Thermocouple. Use the ATB1 for outdoor dry bulb temperatures when finding target superheat. The ATB1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple.

The wrap-tab allows the thermocouple wire to conveniently store on the plug. Just wrap the excess wire around the wrap-tab and feed it through one of the eyes. Keep a few of them set at different lengths for fast, job-specific, switching between thermocouples. No more tangled messes in your tool bag.

SPK2 Pocket-Rod Temp, T1-T2 by Fieldpiece

The newly designed SPK2 Folding Pocket Thermometer is great for taking quick air temperatures. It fits directly in your pocket so you're ready for common temperature checking. The folding rod has a hanging hook so you can easily hang it in a duct or on a grille. The large display shows Min/Max/Hold, has measurements in both Fahrenheit and Celsius, and has a low battery indicator. It also quickly calculates T1-T2, as well as features an Auto Power Off function to save battery power on it's already phenomenal 8,000 hours of battery life on one single AA battery!

ATAF1 High Temperature K-Type Thermocouple with Alligator Clip by Fieldpiece

The ATAF1, K-type thermocouple clips to HVAC/R equipment for convenient placement and hands free testing. Fiberglass insulation withstands high temperatures up to 900°F. Clip it to residential and commercial ovens, broilers, boilers or any other high temperature application. You can also clip it to condenser fins when finding target superheat, evaporator filters, or hard to reach supply vents. The ATAF1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple. The convenient alligator clip is a great time saver when data logging or anytime an extra hand is needed. Great for meters with a 1000°F range.

The wrap-tab allows the thermocouple wire to conveniently store on the plug. Just wrap the excess wire around the wrap-tab. No more tangles.

ATC2 Large Pipe-Clamp Thermocouple 3/8" to 2/14" for Air Conditioning by Fieldpiece

The ATC2, K-type, pipe clamp thermocouple is used to take temperatures of medium to large pipes or any other cylindrical surface within its 3/8" to 2 1/4" jaw range. Using a pipe clamp thermocouple greatly facilitates taking superheat or subcooling measurements. Use the ATC2 for most A/C units. The ATC2 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple.

Because the jaw is designed for HVAC/R, its clamping ability lets you measure temperatures of pipes that are fixed, at any angle, to walls or other surfaces. The sensor reaches correct temperature within a minute.

ATR1 Piercing K-Type Thermocouple for Ventilation Ducts by Fieldpiece

The ATR1, K-type thermocouple is perfect for testing the temperature of air flowing through ductwork. The long rod can reach the middle of ducts for accurate air temperature readings of the entire cross-section. The large handle gives the HVAC/R technician the leverage to push the sharp tip through soft ducts. The ATR1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple.

ATWB1 K-Type Wet Bulb (sock) Thermocouple with Alligator Clip by Fieldpiece

The ATWB1, K-type wet bulb thermocouple can clip to HVAC/R equipment for convenient placement and hands free testing. Wet the durable sock and clip to evaporator filters for indoor wet bulb great for finding target evaporator exit temperature. Clip to return vents for indoor wet bulb temperature great for target superheat calculations. The ATWB1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple. HVAC/R technicians find the ATWB1 extremely helpful when data logging or anytime an extra hand is needed.

The wrap-tab allows the thermocouple wire to conveniently store on the plug. Just wrap the excess wire around the wrap-tab. No more tangled messes in your tool bag.

ATC1 Pipe-Clamp Thermocouple 3/8" to 1 3/8" for Air Conditioning by Fieldpiece

The ATC1, K-type, pipe clamp thermocouple is used to take temperatures of pipes or any other cylindrical surface within its 3/8" to 1 3/8" jaw range. Using a pipe clamp thermocouple greatly facilitates taking superheat or subcooling measurements. Use the ATC1 for most A/C units. The ATC1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple.

The sensor is virtually isolated from ambient conditions, allowing the thermocouple to read the true pipe temperature for as long as it is attached. The sensor's large surface area and increased clamping force help the sensor reach the correct temperature within 30 seconds. Because the jaw is designed for HVAC/R, its clamping ability lets you measure temperatures of pipes that are fixed, at any angle, to walls or other surfaces.

ATS1 Disk K-Type Thermocouple for Surfaces by Fieldpiece

The ATS1, K-type thermocouple is great for measuring the temperature of flat surfaces. The disk tip on the thermocouple is designed to establish good thermal contact. There's no better way to measure a flat metal surface than the ATS1. Infrared gets a close temperature measurement but the ATS1 is more accurate. Fiberglass insulation withstands high temperatures up to 900°F. The ATS1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple.

ATEXT10 10' Extension Cable by Fieldpiece

The ATEXT10 is a K-type thermocouple extension cable designed to give you that extra reach you need when measuring temperatures. It's 10' in length and has a female k-type port on one end and the male plug on the other. It's great for use with rigid thermocouples.

SDP2 Dual In-Duct Psychrometer by Fieldpiece

The SDP2 Dual In-Duct Psychrometer is more than just your everyday HVACR psychrometer. It gives HVACR professionals more insight into HVAC evaporator performance than any other psychrometer, because it takes four evaporator measurements at one time: supply wet bulb, supply dry bulb, return wet bulb, and return dry bulb.

So HVACR professionals get a live, real-time snap shot of the evaporator performance, even while conditions are changing. Based on these live, dynamic readings, the SDP2 Dual In-Duct Psychrometer registers system changes as they happen, and automatically calculates actual Delta-T, Target Delta-T, actual Evaporator Exit Temperature, and Target Evaporator Exit Temperature. Plus enthalpy (BTU/LBM) and Dew Point can be displayed in real-time.

* The SDP2 is a great tool to help HVACR professionals do more all by itself. But couple it with the HG3 System Analyzer and/or the SMAN4 Digital Manifold, and your work improves dramatically in an instant. Not only are you checking and servicing a unit based on live real-time measurements, but the wireless communication lets you be in two or more places at one time!

• Sends live indoor wet bulb readings to the SMAN4 Digital Manifold while charging at the condenser
• Real-time Target Evaporator Exit Temperature and Target Delta T
• Displays actual indoor unit performance, AND calculates how indoor unit should be performing
• Shows enthalpy change across the evaporator -- in real-time
• Wirelessly sends all 4 evaporator temperatures to the HG3 System Analyzer for full system diagnostics
• Plus: Hands-free testing, Bright backlight, Threaded probe locks, Ruled - 38" telescoping probes, Magnetic hanger, Rugged design, Dual display

Includes

• Dual In-Duct Psychrometer - SDP2
• Two Threaded RCONEs - RCONE1
• Blow Molded Case with Padding
• Operator's manual

ATA1 K-Type Thermocouple with Alligator Clip by Fieldpiece

The ATA1, K-type thermocouple can clip to HVACR equipment for convenient placement and hands free testing. Clip to condenser fins for accurate outdoor dry bulb measurement great for finding target superheat. Clip to evaporator filters for indoor dry bulb great for finding target evaporator exit temperature. Clip to supply vents for dry bulb supply temperature. The ATA1 can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple. HVACR technicians find the ATA1 extremely helpful when data logging or anytime an extra hand is needed. The wrap-tab allows the thermocouple wire to conveniently store on the plug. Just wrap the excess wire around the wrap-tab. No more tangled messes in your tool bag.

ATC1R Pipe-Clamp Thermocouple 1/8" to 3/4" for Refrigeration by Fieldpiece

The ATC1R, K-type, pipe clamp thermocouple is used to take temperatures of pipes or any other cylindrical surface within its 1/8" to 3/4" jaw range. Using a pipe clamp thermocouple greatly facilitates taking superheat or subcooling measurements. Use the ATC1R for most refrigeration units. The ATC1R can be used with any of our meters that measure temperature and any thermometer accepting a K-type thermocouple.

The sensor is virtually isolated from ambient conditions, allowing the thermocouple to read the true pipe temperature for as long as it is attached. The sensor's large surface area and increased clamping force help the sensor reach the correct temperature within 30 seconds. Because the jaw is designed for HVAC/R, its clamping ability lets you measure temperatures of pipes that are fixed, at any angle, to walls or other surfaces.