Charging and A/C Analysis, Fieldpiece

VP85 Vacuum Pump-8CFM by Fieldpiece

Fieldpiece is leading the charge in properly performing system evacuation with its new vacuum pumps with RunQuick™ Oil Change System. Available in an 8 CFM DC motor (model VP85), or in a 5 CFM AC motor (model VP55), these revolutionary pumps make evacuation easier and faster.

Good oil is a key ingredient of every evacuation. Clearly view your pump oil through the huge oil reservoir window to see the condition of the oil, and the system. When it's time to change the oil, it's quick, clean, and easy. With the RunQuick oil change system you can replace the oil in under 20 seconds, even while the pump is running without losing vacuum.

Plus the extra wide base helps prevent tipping and spilling oil. Four in-line ports give you tidy hose routing for three different size hoses. Place the cord on the handle for tangle-free storage. Protect gauges and system from oil in unexpected power outages with anti suck-back design.

• On-the-fly oil change in seconds
• In-line four port manifold for easy access
• Backlit oil reservoir to view condition of oil and system
• Sturdy base to stay upright
• Simple-to-use gas ballast with LED indicator
• Water resistant to withstand direct rain
• 15 micron ultimate vacuum
• Anti oil-suck-back keeps oil out of gauges and system

SSX34 Superheat & Subcooling by Fieldpiece

Most non-electrical HVACR problems are charge related. Many systems in operation are undercharged or overcharged. This can cause decreased efficiency and compressor failure. The higher the efficiency of a system, the more critical it is that it is charged properly.

The Fieldpiece Superheat and Subcooling for Air Conditioning and Refrigeration meter, model SSX34, measures suction line, or low side, line temperature and pressure. It then calculates actual superheat in real time using built in P/T charts. It also measures liquid line, or high side, line temperature and pressure, and calculates actual subcooling. Use it to get actual superheat on R-22, R-410A, R-134A, and R-404A fixed orifice systems and actual subcooling on TXV / TEV regulated systems.

Use the "T" fitting to charge to actual superheat or subcooling by putting the SSX34 in-line between your refrigerant bottle and the system. Use it to monitor superheat and subcooling when recovering too.

• Measures suction/liquid line pressure and temperature to calculate and display superheat/subcooling
• Display pressure in PSI or kPa
• Display temperature in °F or °C
• Display superheat in °F or °C
• Display subcooling in °F or °C
• Compatible Refrigerants: R 134A, R 404A, R 410A, R 22
• Includes "T"
• Accepts K-type thermocouples. ATC1 included
• Magnetic hanger
• Thermocouple calibration pot on meter face
• Atmosphere pressure calibration

Competitive Advantages

Many AC system analyzers include PT charts you don't want or need. The SSX34 gives you actual superheat and subcooling in real time like the expensive analyzers do in a rugged, compact design. The SSX34 constantly displays refrigerant line pressure, toggles between line temp actual superheat, and actual subcooling for four of the most common refrigerants found in HVAC/R field service. If need you need more refrigerants in your daily work, check out the HVAC GUIDE® System Analyzer (link to HVAC GUIDE PRODUCT PAGE), models HG2 or HG3, and the ASX14 for a system analyzer and then some. P/T charts for 12 of the most common refrigerants you use in HVACR are included, as well as the software and firmware to generate for printable work orders for customers. For even easier refrigeration testing take a look at the ATC1R pipe clamp especially designed to fit smaller refrigerant lines.

Includes

• Real-time Superheat and Subcooling for A/C and Refrigeration - SSX34
• Pipe-Clamp Thermocouple 3/8" to 1 3/8" for Air Conditioning - ATC1
• 9V Battery (installed)
• Operator's Manual

SVG3 Digital Micron Vacuum Gauge by Fieldpiece

The SVG3 Digitial Micron Vacuum Gauge is a compact, rugged gauge that is loaded with features HVACR professionals need to help them do more. It includes a large, dual display with a rate indicator, alarms, timer, rugged rubberized case, and a hook at strap that allows the vacuum gauge to be hung at any angle.

The SVG3 contains features to make evacuations easier and faster. The display has a bright backlight for high visibility in any situation. To minimize leaks the SVG3 has a schrader depressor that can connect directly to your core removal tool, or directly to the service port. Fewer connections reduce the potential for leaks unrelated to the system. The rate indicator helps determine if there are any leaks within the system.

When the vacuum reaches the low alarm set point, an audible alarm triggers, the backlight flashes, and the integrated stopwatch restarts to show the technician how long the system has maintained a deep vacuum. You can set both high and low alarms. And the timer can display how long it took to get to the alarm and how long the vacuum has been maintained.

• Rate Calculator: View how fast system pressure is rising or falling
• Schrader Depressor: Minimizes leaks by reducing connections
• 1 Micron Resolution
• 0 - 9999 Micron Range
• Contaminated Sensor Test: Clean it if an oil build-up is detected
• Alarms and Stopwatch: Be alerted when system drops to desired level, and know how long it took

Includes

• Micron Vacuum Gauge - SVG3
• Tee Fitting
• Operator's Manual
• 4 AAA Batteries

S365 Charging Jacket for TXV Systems by Fieldpiece

The S365 Charging Jacket is a reliable way to charge TXV systems in cold weather. Normally, low temperatures remove too much heat from the condenser coils, so HVACR professionals should only work on TXV systems when the outside air temperature is 70°F or higher.

Now, the new Fieldpiece Charging Jacket solves that problem, and TXV systems can be accurately charged down to 37°F outside temps. It's the perfect tool to dramatically extend the hours in a day, and the days in a year, where techs can install, service, and charge TXV systems.

Made from parachute-grade material, the Charging Jacket is attached to the top of a split TXV system with hooks, so that the air inlet is not restricted. Then the unit is turned on the the jacket puffs up from the air being forced out of the air outlet.

The top is then adjusted with a drawstring until the proper pressure differential is reached between the high and low side (between 160psi and 220psi for R410A; and between 100psi and 145psi for R22). Once the systems stabilizes for 15 minutes at the correct pressure differential, the system is ready to be charged.:

• Charge TXV systems from 37°F 70°F outside
• Service maintenance contracts before and after the summer heat
• Easy to adjust to reach correct pressure differential
• Great way to increase business during the slow season
• Field tested for accuracy

There is no other product on the market made specifically for this purpose. Currently, HVACR professionals either do not work on TXV systems if it is below 70°F outside, or, if it's an emergency techs might use their actual jackets or cardboard to block the air inlet. The problem is those methods are inaccurate.

The Charging Jacket's advantage is that it works to bring the pressure drop across the TXV to at least 160 psi, and therefore has the same effect on the system as higher temperatures do.

HVACR professionals can now dramatically extend their billable hours because they can work on systems during the off season. So instead of having the do service contract check-ups during the summer rush, service and maintenance can be start early in the spring, and continue late into the fall. And even year-round in many parts of the country.

Includes

• Charging Jacket
• Manual

SRS3 Scale-252lb Job Link by Fieldpiece

The SRS3 Wireless Refrigerant Scale combines modern wireless electronics and rugged materials to perform at the high level you demand. The platform is made of thick aluminum to maintain accuracy over the life of the product. Rubber bumpers and pad cushion both the tank and the scale itself. A new wireless protocol sends platform measurements to both the included remote display and the Fieldpiece Job Link™ mobile app. Platform electronics are sealed to block the occasional moisture seen from rain and splashing. Hang the remote display from a condenser or anywhere metallic and easy to see. The magnetic folding hat holds it right where you put it.

• Sealed platform electronics
• Solid aluminum construction
• Grip pad for cylinders
• Flat top bumpers support larger cylinders
• Connects to Job LinkTM Mobile App
• Magnetic hanger
• Padded case
• Auto-Power-Off (APO)

SRS1 Scale-110lb by Fieldpiece

The new SRS1 refrigerant scale is big enough to comfortably fit a canister, but compact and light weight enough to carry easily.

Heavy Duty

It has the ruggedness needed for HVACR, with thick aluminum walls to maintain accuracy, and rubber feet and rubber pad to soften the impact of daily use.

Charging and Recovery Alarms

You can quickly set a charge or recovery alarm using the big numeric keypad without scrolling digits. Once you dial in how much refrigerant to charge or recover you can keep working, knowing the alarm will sound when it's close to the time to close the valve.

Easy to Carry

Weighing less than seven pounds, and housed in a heavy duty soft-sided case, the SRS1 is easy to throw over your shoulder when you need to carry other things or climb a ladder.

• Charge/Recover Weight Alarms.
• Light Weight and Easy to Carry.
• Max Weight 110 lbs (50 kgs).
• 0.25 oz (0.01 kg) Resolution.
• Non-slip Cushioned Design.
• Full Numeric Keypad for Fast Operation.
• Strong Magnetic Back on Handle.

MR45 Recovery Machine by Fieldpiece

The Fieldpiece MR45 has onboard system monitoring that adjusts motor performance to handle liquid and run twice as fast on vapor. MR45 also steps up low voltage at the power plug to deliver full power to the motor where high voltage drop is a problem.

With a powerful 1HP motor and super-sized condenser, this machine excels on longer and hotter jobs. The easy-to-read display, lightweight (22lbs), straight hose connection ports, and single dial make this machine user-friendly while being tough enough for everyday use, even in the rain.

• Extra large condenser
• Easy access ports
• Long life, low friction ceramic coated cylinders
• Dual cylinder compressor
• Easy hose connections and built in power cord storage
• Large backlit display with status messages

VP55 Vacuum Pump-5CFM by Fieldpiece

Fieldpiece is leading the charge in properly performing system evacuation with its new vacuum pumps with RunQuick™ Oil Change System. Available in an 8 CFM DC motor (model VP85), or in a 5 CFM AC motor (model VP55), these revolutionary pumps make evacuation easier and faster.

Good oil is a key ingredient of every evacuation. Clearly view your pump oil through the huge oil reservoir window to see the condition of the oil, and the system. When it's time to change the oil, it's quick, clean, and easy. With the RunQuick oil change system you can replace the oil in under 20 seconds, even while the pump is running without losing vacuum.

Plus the extra wide base helps prevent tipping and spilling oil. Four in-line ports give you tidy hose routing for three different size hoses. Place the cord on the handle for tangle-free storage. Protect gauges and system from oil in unexpected power outages with anti suck-back design.

• On-the-fly oil change in seconds
• In-line four port manifold for easy access
• Backlit oil reservoir to view condition of oil and system
• Sturdy base to stay upright
• Simple-to-use gas ballast with LED indicator
• Water resistant to withstand direct rain
• 15 micron ultimate vacuum
• Anti oil-suck-back keeps oil out of gauges and system