All Products

2811-756-001 EC 28 Gas Transmitter, Ammonia (NH3) 0-5,000 ppm Range - No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2811-756-003 EC 28 Gas Transmitter, Ammonia (NH3) 0-5,000 ppm Range - Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2811-756-006 EC 28 Gas Transmitter, Ammonia (NH3) - No Display / MODBUS, 0 - 5,000 ppm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2813-428-001 EC 28i Intrinsically Safe Transmitter with Carbon Monoxide (CO) Sensor, 1 ppm Resolution, 0 - 1,000 ppm Range, No Display by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

2813-428-002 EC 28i Intrinsically Safe Transmitter with Carbon Monoxide (CO) Sensor, 1 ppm Resolution, 0 - 1,000 ppm Range, Display by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

2813-716-001 EC 28i Intrinsically Safe Transmitter with Hydrogen (H₂) Sensor, 0.01% LEL Resolution, 0 - 4% vol. Range, No Display by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

2813-735-001 EC 28i Intrinsically Safe Transmitter, Fluorine (F2) - No Display, 0.01 ppm, 0 - 20.0 ppm by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

2813-735-002 EC 28i Intrinsically Safe Transmitter, Fluorine (F2) - Display, 0.01 ppm, 0 - 20.0 ppm by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

2813-740-001 EC 28i Intrinsically Safe Transmitter, Hydrogen fluoride (HF) - No Display, 0.1 ppm, 0 - 10.0 ppm by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

2813-740-002 EC 28i Intrinsically Safe Transmitter, Hydrogen fluoride (HF) - Display, 0.1 ppm, 0 - 10.0 ppm by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States