All Products

18526-98 Miniature Type-J Thermocouple Female Connector, 2 Pin, 5Pk by Digi-Sense

• Glass-filled nylon construction with hollow pins and molded barriers prevent short circuit
• Secure thermocouple wire into positive/negative terminals with screws
• Each connector comes in ANSI color coded material: type J-black, type K-yellow, and type T-blue
• Miniature connectors are suited for small wires and mineral insulated cables

*Please note we can only ship RKI products to customers within the United States

190TMHD-TEC-DF Industrial 190K BTU Direct Fired, Dual Fuel, hidden flame TEC Heater by Master

The MASTER TEC's enclosed flame gives the safety and efficiency of direct-fired technology – all while keeping the flame separate from your workspace and away from construction debris and flammable objects.

Features

• The enclosed flame design makes the workspace safer and allows you duct the heat wherever you need it with optional ducting.
• Dual Fuel ability lets you easily switch from natural gas (NG) to propane (LP), giving you more flexibility in the rental market or jobsite
• With an amazing 99% fuel efficiency, these heaters use almost all the fuel for heat
• Optional Remote thermostat so you can locate the heater away from where the heat needs to go
• Super quiet operation – less than 70 decibels! That's quieter than standard gas fired heaters!
• Don't need heat all the time? Run the MASTER TEC Heater like a fan for air circulation in your workspace
• Certified to top safety standards (ANSI and CSA) and ready for well-ventilated indoor and outdoor use, these heaters deliver peace of mind and high performance
• 1-year limited warranty

BZ1-R000000212 Radius BZ1 Area Monitor, PID, No Pump, ATEx/IECEx, LENS Wireless, French by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

66-5B68-01-W AirLink Alert Wireless Transmitter, Arsine (AsH3) 0-1 ppm, dual battery powered, 900 MHz radio by RKI Instruments

The RKI AirLink Alert series ambient air toxic gas detector is a versatile assembly that uses an electrochemical, infrared or PID sensor element to detect a variety of gases. Battery powered, it communicates wirelessly with controller. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, or PID sensor element
• Battery powered
• Operating temperature range of -40°C to +70°C
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• Graphical LCD with LED backlight
• Output options: wireless, 900 MHz or 2.4 GHz radio
• 1-Year warranty

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants
• Construction
• Temporary or permanent monitoring applications

*Please note we can only ship RKI products to customers within the United States

MX6-H423N201 MX6 iBrid Multi-Gas Monitor, CO(HIGH),H2S,O2,CH4(IR),LE,D,E by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

90536-04 Back-Con Bimetal Thermometer, Dial 5", 24" L; Range; 50-550F/10-290C by Digi-Sense

Accuracy is ±1% full-scale when stem is immersed 2" in liquids or 4" in gases (immerse models with a 2.5" stem length 2" in gases). Measured stem length from the top of the threads to the bottom tip of the stem. Stem dia is 0.25"; threaded connection is 1/2" NPT(M). All thermometers meet or exceed ASME B40.3 standards. Maximum environmental temperature for glass lens thermometers is 500°F (148°C).

• Greater temperature range
• Anti-parallax dial for accurate readings
• Hermetically sealed per ASME B40.3 standard to prevent fogging and protect against tough environments
• Rugged 304 stainless steel construction with a clear glass lens
• Recalibrate using the external reset screw

12017 CGEM II 800 EdgeHD Telescope by Celestron

CGEM II 800 HD combines Celestron's newly redesigned CGEM II computerized equatorial mount with its acclaimed EdgeHD optical system. With 8 inches of aperture and our premium StarBright XLT coatings, the CGEM II 800 HD gives you over 800 times the light gathering power than the unaided eye and is the lightest and most portable telescope in its class.

OPTICAL TUBE INFO:

See the Universe in HD

True Astrograph Quality

Improved Performance

Mechanical Features

• Mirror clutches - Flexible tension clutches hold the mirror in place and reduce image shift when taking long exposure astro-images. Once focused, the flexible rods allow the mirror to be held in place without putting any force or pressure on the mirror assembly, keeping the image centered in the eyepiece (or on the sensor).
• Tube vents - Cooling vents located on the rear cell allow hot air to be released from behind the primary mirror. Each vent has an integrated 95-micron micromesh filter guaranteed to let warm air out without letting dust in.
• Fastar versatility - EdgeHD is the most versatile imaging telescope available today. At its native f/10, you can achieve the image scale necessary to capture the smallest of deep sky objects. Add the optional reducer lens custom designed for your size EdgeHD tube and you can increase your field of view without sacrificing optical performance. A Barlow lens gives you added power for high-resolution planetary, lunar and solar imaging. All EdgeHD optical tubes are Fastar-compatible, allowing the secondary mirror to be removed and replaced with a third party lens accessory for ultra-fast f/2 wide field imaging.

Individually Tested

MOUNT INFO:

A fresh update to the venerable CGEM mount, the CGEM II has a fresh, attractive, bold appearance and is capable of carrying Celestron's higher-end SCT optical tubes (up to 11") securely and vibration free, which is ideal for both imaging and visual observing. Capable of holding 40 lbs. of payload and slewing at 5° per second, you will be able to instantly point to any of the celestial objects in the database.

ERGONOMIC DESIGN

CGEM II was designed to be ergonomically friendly with large Altitude and Azimuth adjustment knobs for quick and easy polar alignment adjustment. The internal RA and DEC motor wiring provides a clean look and an easy and trouble free set up.

INNOVATION

The CGEM II series features Celestron's innovative Polar alignment procedure called All-Star™. All-Star allows users to choose any bright star, while the software calculates and assists with polar alignment. Another great feature of the CGEM II sure to please astroimagers, is the Permanent Periodic Error Correction (PEC) which will allow users to train out the worm gears periodic errors, while the mount retains the PEC recordings.

PERFORMANCE

For objects near the Meridian (imaginary line passing from North to South), the CGEM II will track well past the Meridian for uninterrupted imaging through the most ideal part of the sky. The CGEM II mount has a robust database with over 40,000 objects, 100 user defined programmable objects and enhanced information on over 200 objects. Celestron's CGEM II mount is the perfect fit between the Advanced Series and CGE Series. Offering the portability of the Advanced Series and the precision of the CGE.

VP5-V19Y1100111 Ventis Pro5 Personal Gas Monitor, CO2/CH4 (IR), CO, PH3, O2 (Long-life), Li-ion Battery, Desktop Charger, No Pump, Black, UL/CSA, LENS Wireless, English by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

*Please note we can only ship RKI products to customers within the United States

65-2670-SO21004 M2A Stand Alone Sensor / Transmitter, with j-box, CT-7, non-XP, SO2, 0-10.0 ppm, with remote detector by RKI Instruments

The RKI M2A™ is a state-of-the-art transmitter that can operate as an independent, stand-alone monitor or as part of an integrated system. The M2A connects with an analog or digital signal to virtually any controller, PLC, or DCS. Setup procedures are simplified with user friendly push buttons and OLED menus. It utilizes a magnetic wand technique for performing non-intrusive calibration. The M2A provides an automatic zero drift correction feature, which results in more stable readings and reduces the need for adjustments due to sensor aging.

The housing of the M2A does not need to be opened for zeroing or calibration, making it unnecessary to declassify the area for routine maintenance. It is designed so that a complete field calibration can be performed by one person. Sensor construction is rated Class I, Div. 1 Groups B, C, D for flammables, CO, H2S, O2, and CO2, and Class I, Div. 2 for all other toxics.

The transmitter provides a 4-20 mA output in addition to a Modbus digital output. It also has two levels of alarms with relays, plus a fail alarm with relay. A digital display of the gas concentration, as well as alarm and status lights, can be viewed through the front window.

The toxic sensors are electrochemical type plug-in sensors, which provide high specificity, fast response, and long life. The plug-in design allows quick replacement in the field with no tools required. Toxic sensors are designed for use in Class I, Div. 2 hazardous locations. Sensors available for NH3, SO2, PH3, AsH3, and HCN.

The M2A represents the latest leading edge technology in sensor / transmitters today.

Features

• Operates with or without a controller
• Direct digital readout with OLED cold temperature display
• Available gases include LEL, O2, H2S, CO, CO2, and 100% Vol CH4 / Toxic gases include NH3, SO2, HCN, and more
• Infrared sensor for combustibles and CO2
• 4-20 mA & digital Modbus outputs standard
• 2 fully programmable alarm relays & fail relay
• Non-intrusive calibration via magnetic wand
• Explosion proof construction
• Patented water repellent sensor cover
• User friendly setup, push buttons & OLED menus
• Long-life sensors (2 + years typical)

*Please note we can only ship RKI products to customers within the United States

6302-2172 MGS-450 Gas Detector - IP66, 3 x Relays, Analog Output, Modbus Output, Audible & Visual Alarms - R455A, 0-1,000ppm, Semi-conductor by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

MX6-D1534211 MX6 iBrid Multi-Gas Monitor, NO,CO,SO2,O2,NO2,LE,P,E by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

GS-BC-A-075-G Gasman Single Gas Monitor, 0-100% LEL Methane (unfiltered), Rechargable Battery, Australian Safe Area only by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

MX6-R103Q212 MX6 iBrid Multi-Gas Monitor, PID,CO,O2,CO2,LE,P,F by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

TW20W-PB 20" Twister Oscillating Circulation Fan, White OSHA Guards, Black Square Pedestal by Schaefer

When you're tired of replacing damaged pedestals, use Schaefer OSHA compliant portable circulation fans with heavy-duty pedestal mounts, designed to last many years. Schaefer portable circulation fans deliver quiet, powerful, efficient and long lasting air movement. Use these rugged portable fans in warehouses, work areas, loading docks, greenhouses, farms, and other locations where quality matters.

Features and Benefits:

• Square, round or tripod pedestal for portability needs
• Matched direct drive motors and blades for highest achievable levels of airflow, rated up to 12,000+ cfm
• Powder coated steel guards for corrosion resistance and durability
• Energy efficient design for additional cost savings, draws as little as 1.6 amps
• Thermally protected, heavy-duty, maintenance free, 2-speed motors for long life
• Two-speed pull chain
• Ten foot, 115 volt grounded attached cord
• Mist rings available for additional cooling
• Optional wheel kit for square pedestal available by ordering FP-Wheelkit
• Two year warranty
• Made in the USA

305S34-2-115 30" Galvanized Exhaust Fan in Slant Wall Housing, 5-Wing, 3 / 4 Hp, Belt Drive, 2-Speed, 115V Only by Schaefer

Schaefer slant wall exhaust fans are the first choice of growers and other building owners looking for very low cost, high volume exhaust fans that flush-mount from inside the building and shed water and snow, once installed. Designed for high airflow and high efficiency and available in many sizes and configurations to meet application requirements. Fans ship fully assembled with aluminum inlet shutters, self-adjusting belt tensioner (on belt-drive models) and galvanized outlet guard.

Features and Benefits:

• G90 galvanized construction, for corrosion resistance
• Totally enclosed, thermally protected motors for safety and long life
• Easy belt replacement, minimal maintenance required
• Remote Lubrication System optional
• Suitable for buildings with up to 6" wall thickness using standard rough-in dimensions.
• Available in belt drive or direct drive
• Two year warranty
• Made in the USA