All Products

BZ1-0600000103 Radius BZ1 Area Monitor, NH3, No Pump, UL/CSA, Spanish by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

CC22-701-M CC 22 Series Fixed Transmitter with Methane (CH₄) Sensor, 0 - 100% LEL Range, No Display / Modbus by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

18520-32 Type K Thermocouple Probe Quick DisConnector, Dual with Std-Connector, 18" L, .250 Dia, Exposed Junction by Digi-Sense

The temperature range is for the probe tip only. The handle material may be affected if the probe is rated higher than the handle depending on exposure time, application, and handle material. ABS handles are rated to 220°F (104°C); PVC handles are rated to 200°F (93°C); Stainless Steel handles are rated at 450°F (232°C); Mini Connectors are rated to 392°F (200°C)

• Ideal for continuous monitoring
• Designed with 316 stainless steel sheath
• Response Time: 1.2 - 5 seconds or greater
• Includes a stand alone female connector for instalation to a thermocouple extension cable
• Each probe comes with a color coded ANSI dual standard connector: type J-black, type K-yellow, type T-blue, and type E-purple.
• Custom designs or changes to this product are available upon request

VTS-M0032110101 Ventis MX4 Multi-Gas Monitor, CH4 (0-5%), O2, Li-ion Extended Run Time Battery, Desktop Charger, Pump, Black, UL/CSA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

R61347 FPS-COM 7000 P18 Gcai connection & cable by Draeger

The Draeger FPS®-COM 7000 provides hands-free communication for all wearers of respiratory protection devices during a mission. Excellent voice quality is achieved by removing interfering noises.

For missions under the harshest conditions

For missions requiring respiratory protection you have to expect extreme conditions: thick smoke and noiseobstacles that not only cause stress but also significantly hinder any form of communication. This is even more difficult if a chemical protective suit is required: these suits restrict movement and suppress your voice.

The Draeger FPS-COM® 7000 in connection with the proven full-face mask Draeger FPS 7000 was developed especially for these applications. Each word is transmitted clearly and intelligibly to the members of the team.

Noise suppression for optimum voice quality

The newly developed digital noise reduction automatically suppresses ambient noises and only transmits your voice. In particular, breathing noise is filtered out preventing it from being transmitted to the voice amplifier or the radio. The integrated loudspeakers, with which you can interact directly with the injured people and team members without radio equipment, also have this function.

Wireless connection to the incident commander

Each Draeger FPS-COM 7000 has an integrated PTT button (push-to-talk) to operate a radio that can be connected as an option. You can communicate using a tactical radio by pressing just one button. The tactical radio can be connected with a cable or Bluetooth. The latter means that there are no cables that could become entangled; reducing the risk of snagging.

Hands-free team communication

The Draeger FPS-COM 7000 allows fast and efficient communication within one group or among different ones. And it works without pressing a single button. This improves your safety by not distracting you from your task. The voice-activated function also provides full-duplex communication. This means that you can talk and listen at the same time – as if you were on the phone.

If there is only one radio for the entire group, the system allows the automatic transfer of the received instructions for up to ten group members via short-range radio. This means that only one member of the group needs a tactical radio while everyone is still informed immediately.

Easy operation and individual setup options

The Draeger FPS-COM 7000 was developed with a focus on ergonomic handling and intuitive operation. The set radio group is announced via the earphones. In addition, different alarm tones warn of low battery status or if you are out of range from the team communication. An optional software allows numerous setting options with which you can adapt the system to your precise operation.

You can, for example, define the number of groups. With the integrated switch you can switch between up to seven groups during the mission.

Robust and balanced

The robust communication unit adapts seamlessly to the Draeger FPS 7000. The robust design of the Draeger FPS-COM 7000 can resist even strong shocks and impacts. It is resistant to extreme temperatures and has protection class IP67. This means the Draeger FPS-COM 7000 is waterproof and can be easily cleaned after the operation. In addition, the balanced weight distribution prevents neck muscles from straining and increases wearing comfort – without restricting movement or limiting your field of view.

Flexibility before, during and after the mission

Thanks to its click connection that is easy to operate, the Draeger FPS-COM 7000 can be attached and removed in only a few steps – within seconds and without special tools. This allows greater flexibility to interchange between different face masks which can quickly be ready to operate by simply removing the protective cap.

Therefore, you do not require a separate communication unit for every face mask. The device is easy to clean and maintain due to its easy assembly and distanced position between microphone and face seal.

18526-26 Type K Economic Bolt On Thermocouple Probe #6 Screw with Mini-Connector, 24" Fiberglass Ext. Grounded by Digi-Sense

The temperature range is for the probe tip only. The handle material may be affected if the probe is rated higher than the handle depending on exposure time, application, and handle material. ABS handles are rated to 220°F (104°C); PVC handles are rated to 200°F (93°C); Stainless Steel handles are rated at 450°F (232°C); Mini Connectors are rated to 392°F (200°C).

• Available in #6 (M3.5) or #8 (M4) screw sizes and different lead lenghts
• Response Time: 2-4 seconds or greater
• Each probe comes with a color coded ANSI mini connector or stripped leads: type J-black, type K-yellow, type T-blue, and type E-purple.
• Custom designs or changes to this product are available upon request

MX6-NJ45R211 MX6 iBrid Multi-Gas Monitor, CH4 (IR), CO/H2S, NO2, SO2, PID, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, English by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

0563 4410 440 Delta P Air Flow ComboKit 2 with Bluetooth by Testo

Carry out measurements without any annoying cables: use the kit to handle all relevant measurements in ventilation ducts and at air/ceiling outlets. You will receive the testo 440 dP air velocity and IAQ measuring instrument including differential pressure sensor, two vane probe heads (Ø 100 mm and Ø 16 mm) and a humidity/temperature probe head - all three can be attached to the universal Bluetooth® handle supplied. To make measurements more convenient, both vane probe heads can be combined with the telescope included in the kit. The equipment can be transported safely and conveniently in the robust case.

• Intuitive: clearly structured measurement menu for volume flow and parallel determination of air velocity, differential pressure, humidity and temperature in ventilation ducts, at ventilation outlets and in work rooms
• Space-saving: combine the universal Bluetooth handle with the humidity/temperature probe head or extendable telescope (1.0 m). Vane probe heads (Ø 16 mm, Ø 100 mm) can simply be plugged onto the telescope
• Convenient: wireless probes, internal data storage and USB port for data export
• As multifaceted as your challenges themselves: the testo 440 dP has an integrated differential pressure sensor and can be expanded with a large portfolio of digital probes

Kit Includes:

• testo 440 dP air velocity and IAQ measuring instrument including differential pressure sensor, connection hose, 3 x AA batteries, USB cable and calibration protocol (0560 4402)
• Vane probe (Ø 100 mm) with Bluetooth® including temperature sensor (consisting of 100 mm vane probe head, handle adapter and Bluetooth® handle); bracket for testovent measurement funnel; 4 x AA batteries and calibration protocol (0635 9431)
• 16 mm vane probe head including temperature sensor and calibration protocol (0635 9570)
• Humidity/temperature probe head (Ø 12 mm) including calibration protocol (0636 9730)
• Extendable telescope (up to 1 m in length) for flow probes with a universal handle including 90° angle (0554 0960)
• Combi-case for testo 440 and multiple probes (0516 4401)

GD-K88AI-ASH3 GD-K88AI Smart Transmitter, Arsine (AsH3) 0-0.2 ppm, IS Type by RKI Instruments

The GD-K88Ai is a diffusion style toxic gas detection transmitter ideally suited to meet a variety of toxic gas detection needs. You can choose from a wide range of electrochemical toxic gas sensors to install in this model. The GD-K88Ai includes easy to read LCD display and push button controls for calibration. When it is used with optional intrinsic safety barriers the GD-K88Ai is safe for use in hazardous locations. The low profile design is only 1.9 inches thick and is easy to install. The hinged housing makes it easy to maintain. This transmitter can be installed with any RKI controller, or integrated to existing PLC or DCS system via 4-20mA output (24VDC two-wire, loop powered).

At the heart of any gas detector is the sensor. The sensors for the GD-K88Ai are aged and tested over a one to three month period, typically resulting in a three to five year life span, providing a lower cost of ownership for your gas detection system. These fast-responding sensors are robust electrochemical type that feature higher sensitivity and selectivity.

With over 75 years of sensor technology experience, RKI has the knowledge and capability to provide the most advanced detection techniques and manufacture the most stable and long lasting sensors in the world. As a result the GD-K88Ai is one of the most stable and long lasting toxic transmitters on the market.

Features

• Diffusion style head
• Digital readout of gas name and concentration
• External control buttons for easy maintenance
• Intrinsically safe design
• Quick response sensors
• Many toxic sensors to choose from
• 3 to 5 year typical sensor life
• Low cost of ownership

Applications

• Semiconductor manufacturing
• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone, & electric utilities
• Steel
• Automotive
• Refrigeration
• Food Storage
• Power plants

*Please note we can only ship RKI products to customers within the United States

CS22-729-DM CS22 Fixed Transmitter, R503B, 0(30) - 2,000 ppm, Display / Modbus by GfG

Wherever toxic or flammable gases and vapors must be monitored without requirements for explosion protection, the use of the CS22 is recommended.

Proven and cost-effective

The CS22 works on the principle of chemisorption (CS). Thanks to a wide range of monitorable gases and multiple measurement ranges, the CS22 offers a wide range of uses, from laboratories to industrial applications to refrigeration systems.

Transmitters with electrochemical sensors (EC), are also used with toxic and flammable gases. In contrast, the CS22 is a much more durable and cost-efficient solution. However, the environmental parameters must fit.

Communicates analog and digital

The measured values and status information of the CS22 can be transmitted either analog (4-20 mA or 0.2-1 mA) or digital (RS-485). This allows not only the use in combination with any GfG controller, but also the connection to programmable logic controllers (PLC).

Smart measured value processing

Industry-wide, the trend is towards smart units, such as the CS22, whose integrated electronics process the data already at the measuring point. The linearization of the measurement signal, compensation of temperature influences, detection of malfunctions and information on the next service or maintenance interval are just some of the advantages that result.

Variants for every requirement

The basic version of the CS22 is sufficient for many applications. If a measured value display on site is desired, there is also a variant with display and acoustic alarm.

CS22 Basic variant for a wide range of catalytic sensors
CS22 D with display to show the current measured value

In combination with GfG's powerful controllers, both variants are the right choice for a wide range of gases to be monitored.

08006-47 Liquid-In-Glass Oven Thermometer; 35 to 200C, Organic Liquid Fill, Total Immersion by Digi-Sense

These thermometers are designed for use in specific applications. These Durac thermometers feature markings that are permanently printed on the glass, individually serialized, and red spirit liquid that has a dark scale contrasts against a white background. Some thermometers are PTFE coated for added safety which may cause a slight change in accuracy up to 1 division.

Oven thermometers - designed for high temperature applications and feature a round glass swell to hold the thermometer in place

• Non-mercury liquid

*Please note we can only ship RKI products to customers within the United States