All Products

SPSTAXO1 Sensepoint Detector with Junction Box, 0-25%v/v Oxygen by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offers users a cost-effective solution to their gas monitoring needs, in or out of doors and even in potentially explosive atmospheres. Supplied with a pre-wired junction box, this detector can be installed using conduit or armoured cable and glands depending on the specific needs of the application.

Sensepoint flammable and toxic gas detectors are designed for use in potentially explosive atmospheres, and allow for easy access to terminals via the hinged lid of the junction box. Installation should follow national guidelines using suitably approved armoured cable and glands or conduit.

Supplied with an earth continuity plate for increased resistance to the effects of RFI, the junction box offers the installer a choice of 1/2", 3/4" and M20 connection via conduit or armoured cable and Ex e certified cable glands. Terminals are suitable for use with screened 0.5mm2 (20AWG) to 2.5mm2 (14AWG) cross sectional area cable, as needed to ensure minimum operating voltage at the detector, depending upon installed cable length.

Sensepoint flammable, toxic and Oxygen gas detectors are designed for direct connection with the Honeywell Analytics' range of Touchpoint controllers.

One-Stop Shop

• Flammable, toxic and Oxygen versions available
• Suitable for indoor or outdoor use
• IP65 as standard

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX Certified

• Complies with the latest European standards
• Hazardous area and performance approvals
• Can be used for uncertified applications

Easy to Use

• Factory set operation
• Simple sensor replacement
• Minimal training required

Friendly Installation

• Universal junction box
• One box, three entries
• Metric and NPT compatibility
• Includes earth continuity plate for enhanced protection against RFI

Range of Accessories

• Weather Housing (IP66)
• Flow adaptor
• Collecting cone

66-6204-20 T2A Sensor/Transmitter with j-box, Hydrogen Chloride (HCl), 0-20 ppm by RKI Instruments

The T2A Series toxic gas detector is a versatile assembly that uses an electrochemical sensor to detect a variety of gases. 2-Wire loop-powered to withstand extreme climatic conditions and harsh environments. Magnetic switches allow for nonintrusive calibration while in the field.

Features

• Electrochemical Sensor
• Loop-Powered (2-Wired), 4-20 mA output
• 3 Character, 7 segment display screen with backlight
• 3 Push-button interface (ADD, MENU, SUB) with corresponding magnetic, non-intrusive switches
• Operating temperature range -40°C to +55°C
• Aluminum device enclosure
• 303 Stainless-steel sensor housing
• 1-Year warranty

Industry Applications

• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Automotive
• Semiconductor plants
• Chemical plants

*Please note we can only ship RKI products to customers within the United States

MX6-L603R211 MX6 iBrid Multi-Gas Monitor, CH4,NH3,O2,PID,LE,P,E by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

VN00078 PSS 7000/7000, 45/30, QC, RW, w/BB by Draeger

Before you can protect the lives of others, you have to protect yourself. The Draeger PSS® 7000 self-contained breathing apparatus (SCBA) provides unmatched comfort, durability, and safety in the harshest environments. With unparalleled ergonomic performance, the PSS® 7000 combines trusted pneumatics, flexible fit, and cylinder Quick Connection, freeing the firefighter to concentrate on the task at hand.

Built to satisfy the most rigorous demands

Based on feedback from firefighters throughout North America, the Draeger PSS 7000 SCBA with the Sentinel 7000 monitoring system satisfies the most rigorous demands of today's complex fire grounds. first responders. Backed by a 15-year, bumper-to-bumper warranty, the Draeger PSS 7000 distinguishes itself from other SCBAs in the marketplace with ergonomic performance, clean-ability, and toughness.

Innovative harness system provides unmatched comfort and durability

The Draeger PSS 7000 SCBA is designed so the heaviest components sit at a lower center of gravity to increase stability and balance, allowing the wearer to work more effectively with less fatigue. The PSS 7000 includes an adjustable harness suspension system that provides the ultimate in comfort and extended wear. Durable webbing and advanced compression-molded comfort padding offer up to 6.5-times higher abrasion resistance than traditional padding. The material surface is easy to clean and disinfect with a highl resistance to chemical and mechanical damage.

The harness has a high-grip, anti-slip inner surface that stays securely in place without a chest strap or having to over-tighten the shoulder straps. Cooling channels in the shoulder straps and waist belt reduce the likelihood of compression burns. A stainless-steel, harness-friction buckle makes the SCBA easy to don and doff.

Ergonomic three-position backplate allows freedom of movement

The Draeger PSS 7000 is designed to move with the wearer allowing unrestricted movement while walking, crawling, or climbing. The backplate automatically lengthens and pivots to mirror wearer movements. The unique, self-adjusting and pivoting waist belt keeps the SCBA on the hips when a firefighter reaches, preventing your coat from riding up.

To reduce back strain, the SCBA's weight is designed to ride on the hips. The three-position, carbon-fiber composite backplate adjusts to comfortably fit different torso lengths.

A slide-and-lock harness mechanism allows the harness and waist belt to be connected or removed from the backplate quickly without tools. To minimize the risk of snagging or damage, supply hoses are integrated neatly into the backplate.

Rapid, secure cylinder change-outs save precious time

The PSS 7000 has a lock-and-load system that lets colleagues securely change out cylinders quickly. A proven, quarter-turn QuickConnect adapter allows quick and easy attachment of the cylinder to the reducer, saving time compared to conventional threaded reducer hand-wheel-and-cylinder CGA connections. QuickConnect features a safety interlock system that prevents disconnection at pressures above approximately 70 psi.

Draeger Sentinel 7000–Real-time monitoring

The Sentinel 7000 electronic monitoring system provides options to satisfy the needs of any fire department. Incorporating a centralized power supply and pressure sensor module within the backplate, the robust system combines maximum component protection with balanced weight distribution for reduced physical stress.

Housed in impact-resistant, water-resistant casings, the Sentinel 7000 demonstrates excellent reliability on the fire ground.

An electronic gauge provides real-time monitoring of essential information, including:

• A personal alert safety system (PASS) device
• Intuitive push-button operation for ease of use
• Configurable settings to suit individual preferences
• Data logging for improved post-incident analysis
• Accurate, continuously updated digital display of pressure and time to EOSTI activation (time based on dynamic breathing rate)
• Battery status display
• 360° visual and audible alarms triggered when the PASS is activated
• Automatic self-tests and system tests

BZ1-L357CR1111 Radius BZ1 Area Monitor, LEL (Methane), O2, SO2, Cl2, H2, PID, Pump, UL/CSA, LENS Wireless, English by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

9610C BRICK EP Explosion Proof Lighthead, 100' Cable, Explosion Proof Power Box and Explosion Proof 15AMP Plug by Western Technology

The BRICK™: 9610 LED explosion proof mountable area light is the most versatile and rugged portable explosion proof LED light on the market. Built for a variety of applications ranging from Aviation and Ship Building to Power Generation and Refineries. The BRICK™ is the perfect choice for your portable lighting needs. The BRICK™ is approved for hazardous locations. Class I, Div. 1 & 2, Groups C & D; Class II, Div. 1 & 2, Groups E, F, & G; CSA Zones 1 & 2; Zones 201, 21, 22. Kick-It Tough™ Explosion Proof Lighting

Features

• Approved for: Class 1, Div 1 & 2; Groups C & D
• Approved for: Class II, Div 1 & 2; Groups E, F, & G
• Approved for: CSA Zones 1 & 2; Zones, 20, 21, & 22
• Conforms to UL Stds 153, 781, 844;
• Certified to CSA Stds C22.2#s 12, 25, 137
• Suitable for Wet Location Use
• Certified: Portable Luminary (Portable Luminaire)
• Temperature Rating: T-Code: T5 (-20°C to +40°C); T4 (-20°C to +100°C)
• LEDs Color: ~6000K, CRI >70
• Rated with optics: 50,000 Lux at 1'
• Rated with optics: >11,500 lumens
• Reflective Optic Beam Angle: 60°
• Light Head Power: Models A and C: 36VDC, 2-3A
• Weight: 10 lbs (light head only)
• Dimensions: 10"L x 5"W x 4"H
• Protection: Polyurethane Bumper
• Multiple Mounting Options: Flexible Mechanical & Magnetic mounting (See Mounting Options)

Part Number: J1013300PA

VP5-V00Y2111101 Ventis Pro5 Personal Gas Monitor, CO2/CH4 (IR), O2 (Long-life), Li-ion Extended Run Time Battery, Desktop Charger, Pump, Orange, UL/CSA, English by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

BZ1-LJ673R0111 Radius BZ1 Area Monitor, LEL (Methane), CO/H2S, NH3, Cl2, O2, PID, No Pump, UL/CSA, LENS Wireless, English by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

VTS-L1434101709 Ventis MX4 Multi-Gas Monitor, LEL (CH4), CO, NO2, O2, Slim Extended Li-ion Battery, Desktop Charger, Without Pump, Orange, GOST-R, Russian by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field

Old Part Number: 101325N
New Part Number: J10132.5VN

90446-60 Probe Type-K 12" L Fiberglass Stainless Steel Standard Jack by Digi-Sense

Magnesium Oxide insulated thermocouples, commonly referred to as MgO thermocouples, are used in many process and laboratory applications. Many desirable characteristics make them an excellent choice for general and special purpose applications. They are available in all thermocouple element types, single or dual elements, a wide variety of sheath diameters / materials, rugged in nature, bendable, and have fairly high temperature ratings.

• 316 stainless steel sheath

BZ1-L2345Q0102 Radius BZ1 Area Monitor, LEL (Methane), H2S, O2, NO2, SO2, CO2 (IR), No Pump, UL/CSA, French by Industrial Scientific

When it comes to choosing equipment to protect your worksite from gas hazards, rely on the Radius® BZ1 Area Monitor. No other area monitor protects your workers longer in the field with less setup, user training, and time in the shop.

• Detect up to seven gases using 22 sensor options including PID
• Longest running area monitor with a typical run time of 7 days (168 hours)
• Extended Run Time Power Supply can extend battery to over 1 month
• Ultra-bright blue and red lights and attention-grabbing alarms with distinctive tones
• Audible alarms sound at 108 dB at 1 m to cut through high-noise environments
• Largest display of any area monitor on the market
• Intuitive text-based navigation and configuration
• Customizable alarm action messages such as "EVACUATE" or "VENTILATE"
• LENS™ Wireless enables communication between area monitors and Ventis® Pro5 personal monitors
• All-weather sensor deployment and 360-degree gas path for more accurate detection
• DualSense® Technology increases worker safety by using two sensors to detect the same gas

66-6305-50-R T3A Sensor/Transmitter with j-box, HCN, 0-50 ppm, with 2 relays by RKI Instruments

The T3A Series Gas Detector ambient air hazardous gas detector is a versatile assembly that uses an electrochemical, infrared, catalytic bead sensor element to detect a variety of gases. Wired power (12 to 35 VDC) with 4-20 mA analog and RS-485 Modbus outputs standard. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, catalytic bead sensor element
• Wire powered (3-Wire), 12 to 35 VDC operating voltage
• Digital Modbus output
• Operating temperature range -40°C to +54°C Graphical LCD with LED backlight
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• 2 Individually configurable alarms
• 2 Front panel LED indicators (amber and red)
• 2 Optional fully programmable alarm relays (dry contacts)
• Output options: 4-20mA (3-wire) analog, RS-485 modbus

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants

*Please note we can only ship RKI products to customers within the United States

VP5-KJYQ2111211 Ventis Pro5 Personal Gas Monitor, LEL (Pentane), CO/H2S, O2 (Long-life), CO2 (IR), Li-ion Extended Run Time Battery, Desktop Charger, Pump, Orange, ATEx/IECEx, LENS Wireless, English by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

Part Number: H197150LM40

CS22-736-D CS22 Fixed Transmitter, Ethylene (C2H4) MK 147-5, Display, 4-20 mA, 0 - 1,000 ppm by GfG

Wherever toxic or flammable gases and vapors must be monitored without requirements for explosion protection, the use of the CS22 is recommended.

Proven and cost-effective

The CS22 works on the principle of chemisorption (CS). Thanks to a wide range of monitorable gases and multiple measurement ranges, the CS22 offers a wide range of uses, from laboratories to industrial applications to refrigeration systems.

Transmitters with electrochemical sensors (EC), are also used with toxic and flammable gases. In contrast, the CS22 is a much more durable and cost-efficient solution. However, the environmental parameters must fit.

Communicates analog and digital

The measured values and status information of the CS22 can be transmitted either analog (4-20 mA or 0.2-1 mA) or digital (RS-485). This allows not only the use in combination with any GfG controller, but also the connection to programmable logic controllers (PLC).

Smart measured value processing

Industry-wide, the trend is towards smart units, such as the CS22, whose integrated electronics process the data already at the measuring point. The linearization of the measurement signal, compensation of temperature influences, detection of malfunctions and information on the next service or maintenance interval are just some of the advantages that result.

Variants for every requirement

The basic version of the CS22 is sufficient for many applications. If a measured value display on site is desired, there is also a variant with display and acoustic alarm.

CS22 Basic variant for a wide range of catalytic sensors
CS22 D with display to show the current measured value

In combination with GfG's powerful controllers, both variants are the right choice for a wide range of gases to be monitored.

GD-70DLN-OXY-EC GD-70D Smart Transmitter, O2 (oxygen), 0-25.0%, Lonworks Type by RKI Instruments

RKI Instruments has been making high quality gas detection and monitoring units for over 15 years. With an emphasis on safety and reliability, RKI Instruments excels at providing the best products in gas detection and sensor technology on the market. Every year, RKI strives to improve its product offering and scours the globe for the latest technologies and innovative designs. With the introduction of the GD-70D Series Intelligent Gas Detector, employers and workplace safety managers can feel confident that they have purchased a reliable detector that is built to last.

GD-70D Series Intelligent Gas Detector

The GD-70D Series Intelligent Gas Detector is a new smart gas detection transmitter that monitors combustibles, oxygen, and a wide range of toxic gases. The unit can be used as a standalone device, integrated with other PLC systems, or integrated with RKI's Beacon series of single and multi-channel controllers. Its common platform integrates numerous detection methods and requires very little maintenance.

Exclusive Features

The plug and play intelligent sensors make for easy setup and calibration by internally retaining calibration and sensor data. This allows workers to replace sensors while in the field without the need to reprogram the equipment. For little maintenance and optimal reliability, the internal technology automatically adjusts for long-term zero and span drift. The pump flow is also self-tuning for low maintenance functioning. In general, the smart sensors use electrochemical cell detection, semiconductor detection, pyrolysis-particle detection, galvanic cell detection, and catalytic combustion detection.

The GD-70D Series features a large LCD display that easily reads all notifications and provides a color coded graph for alarm status (first and second alarms are red, and fault alarms are yellow). The LCD screen displays the pyrolyzer connection, gas concentration, detection unit of measurement, the detected gas, the maintenance status, sensor identification, the flow rate, a graph of gas concentration, error codes, and alarm points. All operational settings are completely user adjustable from the front panel. The unit also has a self-diagnosing function which detects sensor trouble and system failure. The Intelligent Gas Detector has a convenient troubleshoot feature through its firmware. This allows users to investigate and resolve their own equipment issues while minimizing maintenance costs.

Specifications

The Intelligent Gas Detector is a convenient size for workplace and wall space efficiency with dimensions of 2.8 D x 4.7 H x 5.9 D and weighs approximately 2 pounds. It can be mounted to a wall easily with a base plate and 2 or 3 screws. Sensor replacements and pump replacements can be performed quick and easily without tools.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

VTS-L1232111217 Ventis MX4 Multi-Gas Monitor, LEL (CH4), CO, H2S, O2, Li-ion Ext Range, Desktop Charger, Pump, Orange, ATEX/IECEX, Portuguese by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field