All Products

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

2106B1716 Sensepoint Hazardous Area Approved Gas Detector, H2 0-1000PPM 3/4NPT ATEX by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

2108N4011H Optima Plus Gas Detector, ethylene version, HART® over 4 to 20mA output, ATEX/IECEx, M25 thread spigot, electro polished 316SS, includes pre-fitted remote gassing cell, polyester mesh dust barrier, nylon weather protection housing and LNP Faradex deluge/sunshade by Honeywell Analytics

Market leading point infrared Hydrocarbon gas detector offering proven performance and sensitivity

With over 40 years experience in the design, manufacture, installation and maintenance of point infrared gas detection, Honeywell Analytics currently has a Worldwide installed base of over 100,000 infrared point Hydrocarbon gas detectors in a wide spectrum of applications from light industrial to the most demanding of offshore petrochemical environments.

Searchpoint Optima Plus is an infrared point Hydrocarbon gas detector certified for use in potentially explosive atmospheres. The unit's infrared detection principle offers the fastest speed of response and fail-to-safe operation, ensuring that your plant is compliant, your personnel are protected and your production process can deliver maximum uptime. Reduced routine maintenance, when compared with conventional electro-catalytic based gas detectors, provides low ongoing cost of ownership. The development of advanced internal fault diagnostics and false alarm rejection algorithms ensures that Searchpoint Optima Plus delivers the highest level of operational integrity.

Typical applications include environments that may suffer from the presence of catalytic bead poisons or inhibitors, or where there are harsh environmental conditions forcing increased time between routine maintenance, for example; offshore oil and gas platforms, floating production storage and offloading (FPSO) vessels, tankers, onshore oil and gas terminals, refineries, LNG / LPG bottling plants, gas compressor / metering stations, gas turbine power plants, refineries, solvent printing and coating plants.

Over 100 gas and vapour calibrations are available. For a list of detectable gases and vapours, please contact our Customer Support team or your local distributor.

Why Infrared?

• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

Why Searchpoint Optima Plus is the right choice...

• Experience gained from over 100,000 units installed worldwide
• Improved reliability
• Optional HART® over 4-20mA output
• Can detect a wide range of hydrocarbon gases including solvents
• Increased reliability with no moving parts
• Increased stability from self compensating optics
• Immune to long term component drift
• Remote functional gas test facility
• Certified for North American and European Hazardous areas
• Increased false alarm rejection
• Increased uptime with contaminated optics warning
• Dynamic Heating Control ensures condensation free optics
• No undetected failures
• Improved diagnostics
• Integral event logging
• Reduced power consumption
• Certified to many hazardous area classification schemes including: European (ATEX), UL, CSA, IECEx and more

2108N4800H Optima Plus Gas Detector, XTC HC CU HART by Honeywell Analytics

Market leading point infrared Hydrocarbon gas detector offering proven performance and sensitivity

With over 40 years experience in the design, manufacture, installation and maintenance of point infrared gas detection, Honeywell Analytics currently has a Worldwide installed base of over 100,000 infrared point Hydrocarbon gas detectors in a wide spectrum of applications from light industrial to the most demanding of offshore petrochemical environments.

Searchpoint Optima Plus is an infrared point Hydrocarbon gas detector certified for use in potentially explosive atmospheres. The unit's infrared detection principle offers the fastest speed of response and fail-to-safe operation, ensuring that your plant is compliant, your personnel are protected and your production process can deliver maximum uptime. Reduced routine maintenance, when compared with conventional electro-catalytic based gas detectors, provides low ongoing cost of ownership. The development of advanced internal fault diagnostics and false alarm rejection algorithms ensures that Searchpoint Optima Plus delivers the highest level of operational integrity.

Typical applications include environments that may suffer from the presence of catalytic bead poisons or inhibitors, or where there are harsh environmental conditions forcing increased time between routine maintenance, for example; offshore oil and gas platforms, floating production storage and offloading (FPSO) vessels, tankers, onshore oil and gas terminals, refineries, LNG / LPG bottling plants, gas compressor / metering stations, gas turbine power plants, refineries, solvent printing and coating plants.

Over 100 gas and vapour calibrations are available. For a list of detectable gases and vapours, please contact our Customer Support team or your local distributor.

Why Infrared?

• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

Why Searchpoint Optima Plus is the right choice...

• Experience gained from over 100,000 units installed worldwide
• Improved reliability
• Optional HART® over 4-20mA output
• Can detect a wide range of hydrocarbon gases including solvents
• Increased reliability with no moving parts
• Increased stability from self compensating optics
• Immune to long term component drift
• Remote functional gas test facility
• Certified for North American and European Hazardous areas
• Increased false alarm rejection
• Increased uptime with contaminated optics warning
• Dynamic Heating Control ensures condensation free optics
• No undetected failures
• Improved diagnostics
• Integral event logging
• Reduced power consumption
• Certified to many hazardous area classification schemes including: European (ATEX), UL, CSA, IECEx and more

2200-013WP GMA 200 Controller, for 13 measuring points, supply voltage 110 V AC by GfG

The GMA 200-MW is our most flexible and advanced gas detection system controller. The design of the GMA 200-MW ensures simple and clearly structured operation in industrial and commercial applications. The system can be configured for control of any combination of GfG gas transmitters for the measurement of an extremely wide range of toxic and combustible gases and vapors.

Flexible modular design

Each GMA 200-MW module can control up to 16 individual gas transmitters (sensors). The self-contained, IP-65 wall-mounted housing facilitates cost-effective and space-saving installation. GMA 200-MW systems are scalable, and easy to expand by adding additional controller and relay modules. Optional gateway modules allow control via remote or touch-screen computer interface.

Easy to configure

Easy-to-use, menu driven GMA 200-MW software allows configuration of sensor type, gas type, measuring point designations, units of measurement, calibration curves, and function of the comprehensive and fully programmable relays. Up to three individual or specified alarm thresholds can be programmed for each measuring point. The GMA 200-MW continuously evaluates the analog input signals of the connected detectors.

Integrated relays

GMA 200-MW systems include comprehensive and fully programmable relays. Each controller is equipped with 8 internal relays. Menu-driven software allows easy assignment of measuring points to relays, single or multiple alarms per point, alarm thresholds, configuration of collective or group alarms, zoning, fault messages and voting functions.

Relay modules

GMA 200-RW relay modules are housed in easy to install IP-65 wall mounted enclosures. Each relay module provides an additional 16 freely configurable relays. A total of four additional relay modules (for 64 additional relays) can be managed by the same GMA 200-MW system. Digital connection with the GMA 200-MW controller allows remote positioning of the relay module wherever it makes the most sense, substantially reducing cabling and installation costs.

Remote terminal displays

Relay modules are available with or without an integral display for readings and system information, making it easy to add a remote terminal wherever needed.

Optional Fieldbus-Gateways

Optional gateway modules allow integration of the GMA 200-MW system into existing company networks based on TCP/IP, Process Field Bus or Process Field Network protocols. Monitoring and system performance data are easily exported for viewing or analysis. A wifi interface can be added to the gateway to allow wireless connection with a touch screen Windows® computer or smart-phone to display or access system information.

GMA 200 power options

GMA 200-MW power options include traditional voltage inputs (2 x 24 V DC, 20-30 V), as well as operation via a redundant, uninterruptible power supply (UPS), ensuring continued operation of the gas warning system even during a power outage.

Integral alarms

The GMA 200-MW includes built-in bright LED strobe light and loud audible alarms.

LED indicator lights

The status of the GMA 200-MW system (including operation, fault, service, alarm and relay status) is shown via LEDs. Individual LED indicators identify the type and severity of the alarm condition, (FLT, AL1, AL2, AL3), and any relays activated by the condition, (R1 through R8).

Datalogging standard

Measured values, mean values, alarm events and faults are permanently stored on a microSD memory card.

Graphical display

Currently measured values are displayed on a backlit, graphical LCD. In the event of an alarm the display changes color from green to red, and highlights the affected channels.

Five buttons enable operation at the GMA 200-MW controller. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the controller, detector and the relays can be retrieved in the operating menu.

Operation via keypad

Operation of the GMA 200-MW is through easy-to-use menus, and a simple 5 button interface for alarm acknowledgement, and viewing information on the status of the gas warning system, detectors and relays. The intuitive push-button controls make it easy to navigate through additional screens of information. The integrated display enables the reading of alarm levels through the controller LCD for easy hazard assessment.

Configuration

A built-in USB port in the GMA 200-MW is used for connection to the configuration software. GMA 200-MW systems connected through a Fieldbus gateway can be remotely connected with a GfG factory service center for configuration, diagnostic or service evaluation.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Additional modules available in IP-65 wall-mounting housings

• External relay module: GMA 200-RW
• Independent power supply: GMA 200-UPS
• Continuous, motorized pump sampling unit: GMA 200-ASV
• Fieldbus gateway: GMA 200-GW

Features

• Advanced and flexible controller for combustible, O₂ and toxic gas
• IP-65 wall-mounting housing, with integral audible and LED alarms
• Flexible, reliable and economic
• Up to 16 transmitters per GMA 200-MW controller in any combination
• Freely programmable relays
• Clearly structured, easy-to-use push-button interface
• Backlit graphic LCD changes color to indicate alarm
• Connect to other measurement devices with 4-20 mA output

2214022 CS 21 Fixed Gas Transmitter, HFC 245 fa, 0(30) - 1,000 ppm by GfG

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants
• Long sensor life
• Fast response

2319900 Hardness Reagent Set, Calmagite Colorimetric by AquaPhoenix

For determination of Calcium and Magnesium Hardness by the Calmagite Colorimetric method. Hach Method 8030. Range: 0.05 - 4.00 mg/L as CaCO3. Reagent set contains: Alkali Solution, Calcium/Magnesium Indicator Solution, EDTA Solution and EGTA Solution for 100 tests.

2811-4501-006 EC 28 Gas Transmitter with Ammonia (NH3), 0 - 100 ppm, No Display / Modbus by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2811-716-001 EC 28 Gas Transmitter with Hydrogen (H₂) Sensor, 0- 4% vol. Range, No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2811-727-006 EC 28 Gas Transmitter with Oxygen (O2), 0 - 25.0% vol., No Display / Modbus by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2813-716-002 EC 28i Intrinsically Safe Transmitter with Hydrogen (H₂) Sensor, 0.01% LEL Resolution, 0 - 4% vol. Range, Display by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

2901-21-009 IR 29 e DB (Increased Safety) Transmitter with Pressure & Humidity Compensation, IP 67, Acetylene (C₂H₂), 0 - 100% LEL Range, Display / Modbus by GfG

Unlike traditional LEL sensors, IR 29 transmitters do not need the presence of oxygen to detect gas. Since they are not affected by sensor poisons they don't require periodic adjustment to make up for lost sensitivity. The IR 29 continuously monitors its functions for proper performance, and can even identify and communicate required service procedures.

Features

• ATEX: II II 2G Ex eb mb ib [ib] IIC T4 Gb
• Patented infrared technology (NDIR)
• Temperature, moisture and pressure compensation
• Maintenance and service-friendly
• 4-20 mA, linear or digital (Modbus interface)

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

3300-46-013 CC 33 Fixed Transmitter with Carbon Monoxide (CO), Stainless Steel Housing, 0-100% LEL (MK 208-3), RS 485 No Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.